Sensor Test
-
Product
HIRF Testing
-
High Intensity Radiated Fields (HIRF) testing simulates high RF peak pulsed and average fields typical of radar environments and is integral to the certification of flight essential avionics systems. L3 Cincinnati Electronics (L3 CE) can perform HIRF testing from 400 MHz to 18 GHz (with traditional average field testing from 10 kHz to 40 GHz).
-
Product
SMD Array Type LCR Test Fixture
16034H
Test Fixture
The 16034H is designed for impedance evaluations of array-type SMD.The minimum SMD size that this fixture is adapted to evaluate is 1.6(L)x0.8(W)[mm]. Since the tip of the measurement electrodes are very thin and the device holder is extremely flat, the device can be shifted and the measurement electrodes can contact each of the elements of the array-type component.
-
Product
AC Current Sensor
RCTi and RCTi 3ph
-
The RCTi & RCTrms sensors convert ac current to an isolated 0-5V voltage or 4-20mA current loop. TA5V-5A allows compatibility with existing 1A or 5A CT metering circuits. Both offer a choice of proportional (rms) and instantaneous outputs. The available RCT current ranges are 0-100A to 0-50,000Apk. Both RCTi and RCTrms provide accurate measurement over a wide bandwidth ensuring precise measurement even with harmonically distorted wave shapes - using a flexible clip-on sensing coil. The RCTs are available as single and three phase models.
-
Product
MEMS Sensor Simulation
SimSENSOR
-
Performance testing of sensor fusion in MEMS inertial and multi-GNSS navigation systems. SimSENSOR extends the capabilities of Spirent’s multi-GNSS simulators by simulating MEMS sensor outputs on a common trajectory with the simulated GNSS RF signals. The simulated MEMSs sensor outputs include user control of representative noise and errors (bias/drift).
-
Product
Hall (Magnetic) Sensors
-
Small, compact axial and transverse Hall generators for measuring flux density. Available for use at cryogenic temperatures.
-
Product
Supercapacitor Test
-
The CT3001A/C battery test systems are upgraded from CT2001A/C with higher precision and data logging rate. The tester can be used to run precision tests for coin cells, pouch cells, prismatic cells, and especially supercapacitors (ultra-capacitors). Each tester has 8 independent channel which can be programmed to run constant current charge/discharge, constant voltage charge, constant power discharge, constant resistant discharge, and direct current internal resistance (DCIR) tests.
-
Product
IO-Link Sensors for Motion Control
-
Encoder for precise position determination and linear measurement, Defined pulse sequence for the reliable detection of rotational speeds, Inclination sensors for precise measurement of angles of inclination on X and Y axes, High measurement accuracy across the total angular range in two axes, High protection rating for the requirements of harsh industrial environments
-
-
Product
Transistor Testing
-
Radiant is introducing an I2C digital-to-analog converter product that can be attached to the Precision Premier II and is controlled from Vision. The addition of this extra voltage source makes it possible for the Premier II to measure the performance of thin-ferroelectric-film gate transistors (TFFTs and MFSFETs). This document explains the theory for such testing and gives examples of such tests using Radiant's SFRAM transistors as examples.
-
Product
Water Quality Sensors
-
Omega offers combination and differential probes for accurate measurement of pH, conductivity, ORP, and disolved oxygen. Submersible sensors for use in drums, open tanks and streams are available.
-
Product
Sensor Bodies
-
The armature - assembled sensor body - is the central component of an inline photometer. We have already designed more than 1000 different sensor bodies and more than 50 types are always on stock. All optek inline sensor bodies are made from high quality materials and are machined with extreme precision. The quality-tested manufacturing tolerances allow optical path lengths of up to 1000 mm, for which the accuracy of the incoming and outgoing light beam is ensured by testing a laser-based coaxiality tolerance test to the reference axis. To cover a wide spectrum of different process conditions, optek sensor bodies can be manufactured from various materials (also for aggressive chemicals or with NACE MR 0175) and adapted with regards to:
-
Product
Battery Testing
BTS 200
-
This testing and maintaining battery system allows to perform measurement of battery voltage, discharging current test and testing of battery capacity. BTS 200 can be connected with external load unit ELU 200.
-
Product
Ultra-slim Photoelectric Sensor
EX-10
-
Panasonic Industrial Devices Sales Company of America
With dimensions of only 14.5 x 3.5 x 10mm, the EX-10 Series Ultra-Slim Photoelectric Sensors are among the smallest and narrowest Sensors worldwide. Despite their ultra miniaturized design, the maximum range of the Thru-Beam version is 1000mm yielding an exceptionally high performance. The EX-10 Series is available in two different basic designs, with a front sensing or side sensing light source, which additionally extends the mounting options in narrow spaces.
-
Product
CMOS Image Sensor
CIS
-
CMOS Image Sensors (CIS) allow multiple camera functions in mobile devices, automobiles and security systems. Nidec SV Probe provides both standard and advanced versions of our CIS cards employing a wide variety of materials ensuring a durable cost-saving solution that can meet the fine pitch and multi-dut challenges of these devices. Other features and benefits include: • Proprietary AC™ Alloy Probes • Reduced Damage Under the Pad • High Frequency Capability • Better Alignment StabilityOur advanced CIS card, the Multiplexer™, is offered specifically for high density and high parallel applications. The Multiplexer™ is built with cantilever needles held into place on one side and shorter AC™ probes on the other which leads to a more stable electrical characterization over other CIS probe card options.Contact your Nidec SV Probe Representative so we can help you find the right CIS product for your testing needs.
-
Product
DDoS Testing
-
DDoS testing missions enable enterprises, operators and governments to test their resilience against DDoS and evaluate their DDoS mitigation infrastructure.
-
Product
Temperature Test
-
Function and safety under extreme conditions. In the field of environmental simulation, ENGMATEC offers a wide range of efficient systems for quality assurance, development and production.
-
Product
Transparent Object Photoelectric Sensors
-
Contrinex Transparent Object Photoelectric Sensors
-
Product
Environmental Testing
-
DATASYST Engineering & Testing Services, Inc.
Simulate real-world environmental conditions to know how your product or component measures up. DATASYST evaluates how your product responds to environmental stressors, including temperature, thermal shock, humidity and altitude.
-
Product
Microwave Testing
170
-
The PICOPROBE® MODEL 170, a high performance microwave probe which incorporates a WR-6 waveguide with our patented coaxial design techniques, has inherent low loss and low dispersion characteristics.
-
Product
Industrial Temperature Sensors
-
AMETEK Sensors, Test & Calibration
Temperature measurement and calibration is our specialty, allowing us to provide much more than just standard sensors and assemblies. Our long experience, developing and producing industrial temperature sensors, provides us with a wide knowledge about applications and customer needs. This enables us to build and deliver quick and custom-designed quality temperature sensors for almost any kind of solutions and applications, no matter what industry. We offer a complete range of thermocouple assemblies and resistance thermometers, as well as thermocouple wire, extension wire, temperature transmitters and accessories.
-
Product
Sensors
3D Fiber Probe
-
Ultra high precision 3D measurements2D image processing combined with a laser distance sensorSelf illumination modeLowest contact force of 1 µNProbe sphere diameters from 0.040 mm to 0.250 mmControl and evaluation software for fully automatic measurements
-
Product
Power Sensors
-
Measure CW power from 10 MHz to 50 GHz. Modulated Average Power Measurement. Peak Power Measurement.
-
Product
Analog Temperature Sensors
-
Analog Devices analog temperature sensors provide current or voltage output proportional to the absolute temperature with accuracies of up to ±1°C. Our diverse range of analog output temperatures sensors can be used in a broad range of applications with no need for external calibration, and with minimal signal conditioning/conversion circuitry. To better suit your varied design needs, our portfolio of temperature sensors are available in multiple package options.
-
Product
Loss Testing
-
Count on Tempo Communications Optical Power Meters to test and maintain your fiber optic networks. Use to accurately ensure that signals are being transmitted at the correct power levels in your fiber network.
-
-
Product
Pressure Sensors
ESPP-MIT1 Sensor
-
ES Systems has developed a series of strain gauge pressure transmitters featuring very good accuracy at a low cost. Each module is based on an all-welded hermetically sealed structure in a single stainless-steel piece. The ESPP-MIT1 is a medium isolated pressure sensor suitable for gas or fluid pressure measurements in harsh industrial or HVAC environments.
-
-
Product
Insulation Testing
-
Measures the total resistance between any two points separated by electrical insulation.
-
Product
Gas Flow Sensors
ESRF-HF Transmitter
-
The ESRF-HF is a family of mass flow transmitters which enable fast and accurate measurements of gas flow over a wide dynamic range. Each transmitter integrates a MEMS flow sensor and readout electronics inside a housing with very small form factor made from stainless steel. The duty pressure of the flow transmitter is 11bar. All measurement data are fully calibrated, and temperature compensated on board, leading to a reduced temperature coefficient and high measurement accuracy.
-
Product
Digital Fiber Sensor
FX-550L
-
Panasonic Industrial Devices Sales Company of America
Panasonic IO-Link technology makes it possible to continuously collect and process data and to control the sensor. This allows users to implement predictive maintenance and to monitor operation in machines and assembly lines. Processing the multitude of data requires users to invest in know-how and time. Panasonic has developed a self-diagnosis function for each sensor type. This function sends sensor data via IO-Link to a higher-level fieldbus, thus informing about the state of the sensor directly. This way, the amount of production data and the work needed to analyze the data is reduced.
