-
Product
12-Channel VME Current Loop/Process Control I/O Module
V220
-
The V220 is ideal for driving and sensing transducers in computer or PLC-based control systems. It can also be used to simulate complex industrial processes to control systems under development and certification.
-
Product
8-Ch Isolated Digital Input And 8-Ch Relay USB 3.0 I/O Module
USB-5860
Digital Input Module
USB 3.0 SuperSpeedDaisy chainable by built in USB hub8-ch Isolated Digital Input and 8-ch Form A-type Relay OutputWide input voltage range (10 ~ 30 VDC)High-voltage isolation on input channel (2,500 VDC )Quick removable European type connectorLED indicators for I/O statusSupported operating systems: Windows 10/11
-
Product
16 Bit PXI I/O Board With 32 Or 64 Analog Outputs
CP266
-
The CP266 is a single-width, 6U, CompactPCI module with 32 or 64, 16-bit analog output channels. These independent analog channels provide ±10 V full-scale outputs. The channel update rate is 2ms, and each output is accurate to ±1mV. The power-up state of the analog outputs can be set to independent user-defined values. Paired output signals are provided to eliminate ground offset effects. The analog outputs are available at a single 68-pin SCSI II shielded connector (32-channel option) or a pair of 68-pin SCSI II shielded connectors (64-channel option).
-
Product
3U OpenVPX Ethernet Switch and Multifunction I/O Board
68G5E
Multifunction I/O
The 68G5E is a 3U OpenVPX board that is configured with an Ethernet Switch module (choose the ES1, 12-Port GbE Cu legacy unmanaged Ethernet Switch, or the ES2 16-Port Cu GbE managed Ethernet Switch with optional 4x 10GBASE-SR 850 nm multimode Fiber Optic interface) and provides additional support for one NAI smart I/O and Communications function module. Uniquely designed, the 68G5E provides ‘independent’ Ethernet Switch capabilities and can operate as a MFIO board end point with access via the 1 x1 PCIe and/or 1x 10/100 Ethernet motherboard Control Port which hosts the NAI Ethernet Protocol Server/Listener application for direct GbE MFIO control. Ideally suited for rugged Mil-Aero applications, the 68G5E delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
General Purpose I/O Modules
HY-TTC 30XH
-
The HY-TTC 30XH is a CANopen based, user-friendly and smart Input/Output module that can be utilized as flexible control system extension in mobile applications. HY-TTC 30XH is used in combination with, and controlled by a master electronic control unit, communicating with the slave module via the standardized CANopen® protocol. By mounting the master control unit centrally on the machine and the I/O modules close to the sensors or actuators, a distributed electronic architecture can be implemented in order to reduce mounting time and cost for cabling.
-
Product
16-Bit, 8-Ch Analog Output PCI Card With 16-Ch Digital I/O
PCI-1723
Analog Output Card
Auto calibration functionA 16-bit DAC is equipped for each analog output channelSynchronized output functionOutput values retained after system hot reset2-port (16-channel) user-defined digital input/outputBoardID™ switch
-
Product
Real-Time Vision I/O Card With Multifunction
AX92350
-
The AX92350 is a PCI Express x1 vision card with vision-specific I/Os and real-time controls. A machine vision system requires accurate interaction between lighting, camera, actuator and sensor devices. The AX92350 vision I/O card integrates LED lighting controller, camera trigger, encoder input, and digital I/O to connect and control all the vision devices. The encoder input function is well-suited for conveyor applications. There are 4-CH trigger input, 4-CH or 8-CH trigger output, 4-CH LED lighting control, 1-CH quadrature encoder, 8-CH isolated DI and DO, and 1-CH auto measurement function for rugged machine vision and video surveillance applications.
-
Product
Software Abstraction for Easy Control of Digital IO Devices
Konrad DigitalIO
-
It consists of three modules:- A windows driver which is responsible for the communication and device abstraction- A DLL with NI TestStand Test Steps which allows easy integration in automated production environments- A standalone executable which simplifies debugging and setup of test sequencesThis architecture allows to open a communication channel from multiple instances to the same device. This is important when for example an I/O channel should be used in two independent applications.
-
Product
I/O Modules
-
esd offers a wide range of compact stand-alone I/O modules for CANopen and EtherCAT. The modules of the CAN-CBX series offer the possibility of easy mounting in the DIN rail due to the InRailBus. All CANopen modules operate according to CANopen profiles in compliance with the CiA® specification CiA 301.
-
Product
Digital I/O Board, 32 Isolated I/O Channels, 24 V.
APCI-1500
-
PCI interface to the 32-bit data busConnector compatible to PA 1500Connector and software compatible to CPCI-150016 isolated input channels, 24 V, including 14 interruptible3 software-programmable counters/ timers16 isolated output channels, 10 to 36 V, output current 500 mATimer-programmable watchdog for the reset of the outputs to ??Diagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdogInterrupt triggered through watchdog, timer, errorOne ground line for all inputs and one ground line for all outputs
-
Product
PCI Multi-function I/O Module
APC730
-
APC730 I/O boards provide a variety of I/O functions on a single card. These high-density boards perform both high-speed and high-resolution A/D and D/A conversion and also handle digital I/O plus counter/timer functions.
-
Product
EtherCAT Coupler With ID Switch Slice I/O Module
AMAX-5074
EtherCAT Slice IO Module
Function : Coupling EtherCAT IO modules to 100BASETX EtherCAT networkCable : Ethernet/EtherCAT cable (min. Cat. 5), shieldedDistance between stations : Max. 100 m (100BASETX)Number of configurable IDs : 256 (2 x 16-bit ID switch)Bus Interface : 2 x RJ45 (1 x Input, 1 x Output)
-
Product
I2C Interface for Digital I/O Control
EE301-I2C
-
Cable can be used with EE301-I2C or EE301-DCMI Model Numbers only. Cable + Power for Loads & Control Modules / Connects to a PC Parallel Port / Supports (2) Electronics Loads & Control Modules / 6' Power cable & 5' Data cable
-
Product
PCIe/104 OneBank FPGA I/O Board
EMC²-7A100
-
Sundance Multiprocessor Technology Ltd.
The EMC2-7A100 can use commercial, industrial or automotive graded Artix-7 FPGAs and is complimented with 1Gbyte of DDR3 local storage, 32Mbytes of Flash memory for storage/configurations and has 68x free differential I/O pins which are routed to a VITA57.1 FMC-LPC high-speed connector for bespoke interfaces.
-
Product
REM-11100, 2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O
784748-01
Voltage Input Module
2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O - The REM‑11100 is a voltage input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11100 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. This module features 2‑, 3‑, and 4‑wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling.
-
Product
Regular Flex I/O For Remote Switch
98R17500401
Expansion Module
Flex I/O expansion on the front panel for same-side cablingCompatible with MIC-7500, MIC-7700, MIC-770, MIC-7900
-
Product
16-bit, 100KHz, 16SE/8DIFF A/D Inputs; 4 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, All Isolated
APCI-3120-16-4
-
*Optical isolation 500 V*16 SE or 8 diff. inputs*Data transfer rate: 100 kHz*16-bit resolution*4 analog output channels*Data transfer rate:30 kHz*14-bit resolution*Output voltage: 0-10 V, ±10 V, (set through software)*Each output has its own ground line*Driver capacity: 5 mA/500 pF*Short-circuit protection: EMI filters*Data exchange through 16-bit I/O digital*4 digital inputs*and 4 digital outputs, 24 V , opto-isolated
-
Product
SCB-68A, Noise Rejecting, Shielded I/O Connector Block
782536-01
Terminal Block
68-Pin Female Screw Terminal to 68-Pin Female D-SUB, DIN-Rail, Shielded I/O Connector Terminal Block - The SCB-68A provides a shielded I/O connection for interfacing I/O signals to plug-in data acquisition devices with 68-pin connectors. This Terminal Block combines with shield cables to provide low-noise signal termination. The SCB-68A incorporates a completely redesigned mechanical enclosure with a magnetic removable lid, DIN-rail mount compatibility, and a resettable fuse. It is compatible with single- and dual-connector Multifunction I/O with 68-pin connectors. The SCB-68A also includes two general-purpose breadboard areas and an onboard cold-junction compensation sensor.
-
Product
PC/104 OneBank I/O Board
EMC²-KU40
-
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-KU40 to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-KU40 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
Product
3U cPCI I/O & Comm Board
75C3
Multifunction I/O
NAI’s 75C3 is a 3U cPCI multifunction I/O and communication board with three independent function module slots. Two of the slots can be configured with a variety of I/O and communication functions; the third, with either a combination module featuring four multiplexed A/D channels and 28 Discrete I/O programmable channels, or with a reference supply. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
I/O Extension Stack Board For DP, USB, And Audio Extension
PCE-SA01
-
I/O extension stack board1 DP, 2 USB 3.0, MIC-in, LINE-outDimensions (L x H) : 68 x 125 mm (2.67" x 4.92")Supports Model: PCE-3029, PCE-4128, PCE-4129Support Model: PCE-5029/5031/5032/ 5033/5129/5131/5132/5133/7129/ 7131/7132/7133; PCE-3029/3032/ 4129/4132
-
Product
Analog Output Module For Remote I/O
Analog Output Module
The Analog Output Module for Remote I/O features a 2-wire spring terminal connection, selectable output ranges (0 V to 10 V, ±10 V, 0 V to 5 V, ±5 V, 0 mA to 20 mA, 4 mA to 20 mA, and ±20 mA) output ranges, and short circuit proof outputs. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Analog Output Module for Remote I/O from a real‐time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
-
Product
24-Channel Digital I/O With Digital Integration Features On PCI Express Mini Card
mPCIe-DIO-24A
-
The mPCIe-DIO-24A is a type F1 PCI Express Mini Card (mPCIe) and optional cable assembly (D-Sub 37-pin Male connector) designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program. This also allows for simple and trouble-free migration from other ACCES PCI and PCI Express digital I/O cards, but also provides for advanced features enabled by the onboard FPGA logic.
-
Product
General Purpose I/O Modules
HY-TTC 36X
-
HY-TTC 36X is a CANopen-based, cost effective, modular and user-friendly solution for extending the number of I/Os in mobile applications. This controller is best suited for different kinds of control tasks in a vehicle and acts as slave unit in a CAN-based network architecture.
-
Product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 5V
APCIE-1564-5V
-
32 digital inputs, 5 V, isolated16 interruptible inputs32 digital outputs, 5 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
LVDS Digital I/O with Kintex UltraScale FPGA - 3U VPX
Model 54810
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure
-
Product
Rugged Analog I/O Modules
-
Our extensive line of analog I/O modules currently includes PC/104, PCIe MiniCard and FeaturePak form-factor products, providing both A/D and D/A functions. Most of these products also include digital I/O and counter/timer features. A unique feature of Diamond analog I/O modules is our patented autocalibration technology, which can reduce analog measurement errors by up to 10 times relative to conventional designs.
-
Product
Digital I/O
-
With digital I/O cards, static or dynamic bit patterns can be generated or recorded. Each bit is assigned a control signal for an output and a sensor signal for an input. The usual voltage range for the inputs and outputs is between 2 V (TTL) and 24 V (automation).
-
Product
24-Channel Digital I/O With Digital Integration Features On M.2
M.2-DIO-24A
-
The M.2-DIO-24A is an M.2 card, and optional cable assembly (D-Sub 37-pin Male connector) designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program. This also allows for simple and trouble-free migration from other ACCES PCI and PCI Express digital I/O cards, but also provides for advanced features enabled by the onboard FPGA logic.
-
Product
32-Ch Isolated Digital Input And 16-Ch PhotoMOS Relay USB 3.0 I/O Module
USB-5855
Digital I/O Module
USB 3.0 SuperSpeedDaisy chainable by built in USB hub32-ch digital input and 16-ch PhotoMOS Relay output (Form A) isolationWide input voltage range (10 ~ 30 VDC)1500 VDC optical isolation for relay outputsQuick removable European type connectorLED indicators for I/O statusSupported operating systems: Windows 10/11
