Selectors
-
Product
(Automatic Redundant Battery Selector With Source Control And Monitoring)
ARBS 2600
-
La Marche Manufacturing Company
Our product is designed with high powered diodes to select the higher voltage of the two isolated DC power sources. The ARBS selects power from the best available battery while isolating the alternate battery bank. The special heat sink diode assembly is manufactured to handle high output requirements with safety margin to spare.
-
Product
MR50 THT Vertical | 12 Positions | 4 Poles | 1/4''-28 UNF
MR50-B5/6xA/B
-
Highly robust Ø 1/2" selector with 30° indexing angle, up to 6 Ncm switching torque and operating temperature from -45 to 85° C
-
Product
HDG and OBS Track Select Panel
TA-260
-
Universal Heading and Track Selector Panel This panel provides a synchro transmitter for Heading and a synchro resolver for Nav converter alignment. The synchros are mounted on industry standard 18:1 dual speed drives for maximum accuracy and repeatability. This unit can be used to calibrate both manual and automatic converters. This panel provides a rear mounted interface connector as well as front mounted tip jacks for independent breakout if so desired. The TA-260 also provides two discrete switches associated with the resolver configuration. The 30Hz/400Hz switch is provided to allow the resolver to be properly compensated for the type of Nav converter to be aligned. The second switch allows you to open or short the resolver rotor lead as may be required by some newer GPS equipment. This panel is lightweight enough for portable use or may be rack mounted.
-
Product
Installation Support
-
Schweitzer Engineering Laboratories, Inc.
Completing a substation, panel, or a control house requires more than relays. SEL provides contact arc suppressors, linear power supplies, displays, selector switches, panel-mount hardware, bezels, dust covers, cables, and other accessories essential for a successful power system project.
-
Product
16 or 32 channel Digital to Analog Converter
LS-71-P
-
The LS-71P PCI D/A Converter (DAC) board provides high speed analog outputs of PCM decommutated data allowing real time data displays using strip chart recorders or similar devices. The LS-71-P board is designed to be used in conjunction with the Lumistar LS-50-P Multifunction PCM Decommutator boards and uses an over-the-top communication bus directly from the decom to the DAC to avoid any glitches in the analog outputs due to PCI bus activity. Direct “mailbox” type access is also provided to allow the user to send information through the PCI bus to the DACs. The DAC board design allows 2 LS-50-D Multifunction decom boards to be used with a single DAC board allowing tagged data from either data stream to be directed to any DAC channel. An optional LS-71-DB Word Selector Daughterboard allows two additional data streams to be monitored with the ability to select channels from 4 data streams to be displayed on any DAC channel. The design incorporates an extremely large memory (more than 200,000 16-bit words) used as a lookup table allowing linear or non-linear EUconversions with constant delay regardless of the number of polynomial coefficients required. Standard product supports a single decom, however, dual decom support is available as an option.
-
Product
Speaker Component Checker
Cab Driver
-
Whirlwind Music Distributors, Inc.
The CAB DRIVER is a test device for checking the operation of the speaker components within enclosures. A pink noise signal source is sent through pushbutton selectors to an assortment of speaker connectors, including Speakon NL8 and NL4, 1/4" TS and banana jacks. Speaker/ Polarity/ Impedance/ Pink Noise Generator
-
Product
Oil Test System
-
The Oil Test system Model OTS 2K1 is portable transformer oil Test system. It is a specially designed for accurate measurement of Loss Factor, Permitivity & Volume Resistivity Measurement of Transformer Oils & Petroleum jellys. The test frequency is 50 Hz . The system is provided with Mode Selector Switch so that once the oil cell is connected, it can measure all Three parameters in different modes without handling the test leads.
-
Product
Probes And Accessories
-
Choose from a broad portfolio of Tektronix probes and accessories, all perfectly matched to our industry-leading oscilloscopes. With over 100 choices available, select the oscilloscope probe you need for your specific testing application. Download our Probe Selector Guide here.
-
Product
Phase Monitoring / Potential Selector Relay
-
This is a phase failure relay suitable for 3 phase supplies. The relay is designed to automatically change over from the primary supply to the secondary supply if any phase of the primary supply has faulted.
-
Product
Relay Testers
-
Outputs 100VA single-phase voltage and 180VA single-phase currentEquipped with counter function, output selector, auto sweep function, memory function, DC output for testing, master/slave function, etc.Output frequencies of 50Hz, 60Hz, and 10Hz to 200Hz, using external synchronization or line synchronization (selectable)Equipped with GPIB/RS-232C interfacesWeight: 19.5kg
-
Product
MR50 THT Vertical | 16 Positions | 2 Poles | 1/4''-28 UNF
MR50-A3/4xA/B
-
Highly robust Ø 1/2" selector with 22.5° indexing angle, up to 6 Ncm switching torque and operating temperature from -45 to 85° C
-
Product
07R THT | Horizontal Or Vertical | Threaded Or Non-Threaded
07R-Selector-Overview
-
Miniatur selector with shaft or screwdriver with bezel, PCB mounting and up to 3.5 Ncm switching torque
-
Product
Surge with 3 Phase Transfer Switch Consoles
TC Model
-
(Surge with 3 Phase Transfer Switch Consoles) Although all PJ Surge Testers are capable of testing 3 Phase Motors, this "TC" Model has the same characteristics as the "C" Model, but includes a Built-in 3 Phase Test Selector Switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
Product
04 With Soldering Eyelets | 4 Wafers | 24 Positions
04-4xx3-00/30-xx
-
Very robust, multi wafer selector with 15° detent angle, switching torque up to 20 Ncm and a rotational life up to 25'000 cycles
-
Product
Thermocouple Bench Selector Switches 6 or 12 Way IEC, ANSI
-
A 6 or 12 way selector in a moulded housing with aluminium front and rear panels. The rear inputs are switched via a front mounted rotary selector switch to the single output socket. Internally wired with thermocouple compensating cable and available with IEC or ANSI thermocouple types K, J, T, N & R/S.
-
Product
01 With Pins For PCB Or Soldering Eyelets | 6, 10, 12 Positions | M6, M8, M10
01-Selector-Overview
-
A versatile range of compact selector switches featuring flexible termination options (PCB pins or solder eyelets) and various mounting sizes. This series supports 6, 10, or 12 positions with indexing angles of 30°, 36°, or 60°. Constructed with stainless steel shafts and optional IP68 sealing, these switches are the go-to solution for rugged embedded environments.
-
Product
Versatile 5-Channel Industrial Amplifier/ Conditioner Instrument
MODEL TIO-3000
-
The TIO-3000 System was originally designed to perform precision summing on 2, 3 , or 4 load cell signals for weighing applications. Development has progressed into accessory modules with considerable versatility for user defined configurations in a compact economical five (5) slot system with built-in meter and channel selector. Please see below for more information on the four available plug in modules and for available system configurations.
-
Product
Electronic Cards
-
Our product range includes a wide range of PDBC Relay Card, Local Remote Selector Card, Monitor Card and Fuse Failure Relay Card.
-
Product
04 With Pins For PCB | 4 Wafers | 12 Positions
04-4xx4-20/70-xx
-
Very robust, multi wafer selector with 30° detent angle, switching torque up to 20 Ncm and a rotational life up to 25'000 cycles
-
Product
Torsion Testing Machine
-
Unique ‘TALCON-CLAW’ Grips for Round and Flat SpecimensTorsional Speed of 0.1/0.2 RPMTorque Compensated MotorsMaintenance Free Gear Box Auto Range Selection with Range Selector Wheel (Optional)3 or 4 Torque Ranges for Higher Accuracy (Optional)Load-unload Capability Variable Speed Drive (Optional)
-
Product
MR50 THT Vertical | 16 Positions | 4 Poles | 1/4''-28 UNF
MR50-A5/6xA/B
-
Highly robust Ø 1/2" selector with 22.5° indexing angle, up to 6 Ncm switching torque and operating temperature from -45 to 85° C
-
Product
Low Selector Isolating Transmitter
Model TWL
-
Kusam Electrical Industries Limited
• Aux. Power AC 85 ~ 265V or DC 85 ~ 300V• High Accuracy 0.1% RO at 23 °C ± 5 °C• Input / Output User Selectable• PC Plastic Case, DIN Rail or Wall Mounting• High Dielectric Strength (AC 1.5KV/Min, between Input / Output / Power)
-
Product
HIPOT Insulation Testers
-
Crown high voltage, transformer type hipot insulation testers are safe, easy to use for quick, positive determination of grounds, shorts, and broken wires in motors, transformers and other low voltage equipment or wiring systems. A turn of the selector switch gives a selection of seven voltages;500, 1080, 1250, 1500, 1750, 2000 or 2500 volts calibrated to +/- 5% accuracy; NEMA recommendation for insulation test is twice normal voltage plus 1000 volts. Since this instrument has a capacity of 2500 volts, it readily accommodates all normal requirements.
-
Product
RS-232 to RS-422 Interface Converter
Model 63-2SA
-
FEATURES: Full Duplex Signals; DTE/DCE Switch; TD and RD Indicators; DC to 115.2 KBPS. The Model 63-2SA provides a hardware conversion for full duplex signals between RS-232 and RS-422 I/O ports. Since the RS-232 port may look like a computer or a modem, the converter is equipped with a DTE/DCE selector switch.
-
Product
Current Probe
PA-699
-
*High sensitivity: 1mA, High frequency: 1.5MHz. They are all 10 multiple calculation. Calculation is not making mistakes.*Max measuring current: +/- 40A DC / 80 Ap-p*Max sensitivity: ≧1mA*Bandwidth: DC ~ 1.5 MHz*Rising Time: 0.23 uS*Overload indicator*1V/A, 0.1V/A 2 ranges selectors*Input power switching (priority circuit) and battery available*Dispatching design, high durability
-
Product
Serializer/Deserializers & Selector Muxes
-
Serializer/Deserializer muxes use both rising and falling edges of the clock to serialize the data from parallel inputs to serial output while demuxes deserialize the data from its serial input to parallel outputs. Selector muxes routes the differential inputs to either one or more of the desired outputs upon assertion of the appropriately selected port. Muxes can be used in various applications including High Data Rate Ethernet, Fiber Communication, Signal Routing and Broadband Test & Measurement Equipment.
-
Product
Track Select Panel
TA-6
-
A universal master HDG/OBS selector panel with heading synchro transmitter, To/From meter and precision track selector. This panel requires a customer supplied RMI. Panel test jacks allow for external use of both the Hdg transmitter and precision resolver. This standard panel will allow by the book testing and mates directly with TA-5. Click on picture for larger view.
-
Product
High Power LED Photo-color-semi Automatic Selector
-
Shenzhen Chuangxin Instruments Co., Ltd.
Can divide LED in to several groups by chromatic coordinates, correlated color temperature, dominant wavelength or luminous flux.
-
Product
Key Selector Switch
SG-D1
-
Panasonic Industrial Devices Sales Company of America
Key Selector Switch with direct open operation function and pin tumbler design for high security.
-
Product
Autopilot Directional Gyroscopes
4000C/D-series
-
The 4000C/D is an air-driven directional gyro with A.C. autopilot pickoffs. Left turns produce clockwise dial rotation and right turns produce counter-clockwise rotation. Two knobs control the gyro. The left knob is used to cage the unit, and the right knob is used to select the instrument’s heading. To change course, the right selector knob is pressed and turned to disengage the dial shaft and set the pointer to a new heading. Releasing the selector knob re-engages the pointer with the dial shaft. As the aircraft turns onto a new course, the pointer returns to its original position. The on-course position of the pointer is always at the top of the azimuth circle (0° on the dial with the aircraft headed north).
