-
Product
RF Synthesizers Modules
-
Holzworth Instrumentation, Inc.
Holzworth's RF Synthesizers Modules were originally designed as the internal, tunable LO test sources for Holzworth phase noise analyzer products. Due to the need for easy integration, the HSM Series designs incorporate a long list of electrical and mechanical features to satisfy the demanding requirements of today's high performance communications systems and integrated test systems. FIELD PROVEN RELIABLITY with MTBFs exceeding 240kHrs.
-
Product
RF Communication Module
RF-200
-
The RF Communication module allows remote operation of asingle sensor or a chain of sensors. The remote single sensoror chain is connected to an RF Communication module and to aBattery Module which powers them all.
-
Product
RF Coaxial Probes & Probe Positioner
-
Fairview Microwave’s line of coaxial RF probes and RF PCB probe positioner are ideal for use with chip evaluations, signal integrity measurements, coplanar waveguide, substrate characterization, gigabit SERDES and test fixture applications. The RF coaxial probes provide return loss better than 10 dB and a maximum operating frequency of 20 GHz. The probes have a 3.5mm female interface, a pitch of 800 or 1500 micron and they can be cable-mounted. They feature gold-plated contacts and can be used by hand, with or without a probe positioner. Compliant coaxial GSG (or GS) pogo pins allow for a broad range of probing angles. The RF PCB probe positioner can hold coaxial probes, has articulated joints and delivers multi-axis positioner control. This positioner also boasts a magnetic mounting plate with on-off positioner switch.
-
Product
Microwave& RF Signal Generator
-
Berkeley Nucleonics Corporation
A low-noise, fast-switching, high power and offers wide frequency ranges.
-
Product
Low Noise Amplifiers
-
High-intercept and high-gain low noise amplifier modules. Wide supply voltage range. Custom designs available through LNA design services.
-
Product
End of Line Noise Test System
-
End of Line Noise Test Systems from VIacoustics are designed to support end of line product noise testing on factory floors and quality assurance environments. Using the Limit Analysis features of the Nelson Acoustic Trident software, users can set noise emission maximum, minimum or control range criteria based on Awtd and/or 1/N octave band criteria. Criteria can be customized for most any type of product based on the noise emissions of known good and bad units. The large front panel Pass/Fail indicator allows operators to quickly determine if units meet the criteria. Data on units that fail can be exported for further analysis.
-
Product
Phase Noise Generator / Calibrator
PNG-A
-
Noise eXtended Technologies S.A.S.
The PNG-A is a high precision generator used in Test and Measurement instruments calibration. It is a Signal Generator with precisely computed phase and amplitude noise characteristics. With its wide frequency offset range, 1Hz to 1 MHz offset, and its programmable Phase and Amplitude noise in real time, this is the ideal standard to calibrate phase noise analyzers, Signal Source Analyzers and Spectrum Analyzers.
-
Product
RF and Vector Signal Analysis Software
SignalVu-PC
-
SignalVu-PC is the foundation of RF and vector signal analysis software that helps you easily validate RF designs. Whether your design validation needs include EMI/EMC pre-compliance testing, wideband radar, wireless LAN or frequency-hopping communications, the SignalVu-PC comprehensive suite of tools and application software can speed your time-to-insight by showing you the time-variant behavior of these signals.
-
-
Product
RF Spectrum Analyzers
RF Explorer
-
RF Explorer is a new series of low-cost, portable, RF spectrum analyzers designed by Arocholl that are available in a variety of frequency ranges. Nuts About Nets has been developing diagnostic tools for troubleshooting wireless networks for a number of years and when RF Explorer was first introduced to us we were extremely impressed. The price-performance of these RF spectrum analyzers is truly remarkable and is the best, by far, on the market -- nothing else comes close. These RF analyzers operate both standalone as handheld devices, plus they interface via USB cable to a PC running more sophisticated data acquisition and analysis software. Prices for these RF spectrum analyzers (including PC software) begin at $119 USD -- which is unheard of in the test equipment industry.
-
-
Product
WiGig RF Tester
IQgig-RF Model B
-
When used in conjunction with IQgig-IF, an optimized test solution for conducted testing of WiGig chipsets and baseband modules, the IQgig family products provide a total test solution for R&D characterization and high volume manufacturing.
-
Product
RF Flexible Cable Assemblies
-
Industry leader in manufacturing excellence, tailored performance, and rapid delivery of custom cable assemblies. The Flexible version, our Mini-Flex, has an FEP jacket, round braid and inner spiral shields and is available in 2 diameters, .105" &.165". The Semi-Rigid cables are available with a copper or aluminum jacket and available with a selection of different platings and 4 different diameters (.047", .085", .141" & .250"). The Conformable®, or hand formable (BJ - Braided Jacket), has a tin filled braid with a metal foil underlay and is also available in the same diameters as the Semi-Rigid type . All 3 types (Semi-Rigid, Conformable & Mini-Flex) are manufactured using the same type dielectric core and have virtually the same electrical performance. The decision of which cable to use should be primarily based upon your application.
-
Product
Ultra-Low Noise, Precision Voltage Reference
ISL21090
-
The ISL21090 is an ultra-low noise, high DC accuracy precision voltage reference with a wide input voltage range. The ISL21090 uses Renesas' advanced bipolar technology to achieve sub 1.0µVP-P (1.25V option) 0.1Hz to 10Hz noise with an initial voltage accuracy of 0.02% (2.5V option).
-
Product
Fixed Aperture RF Current Monitoring Probe
TBCP1-200
-
The TBCP1-200 is a fixed aperture RF current monitoring probe.The probe has a 3dB bandwidth of approximately 200 MHz. The aperture of the RF current monitoring probe is 25 mm. Its transfer impedance is > 14 dB Ohm in the range from 40 kHz to 200 MHz.
-
Product
RF Power Meters
-
Peak Power Analyzer has been totally redesigned from the inside out. This meter is taking performance to a new peak and changing the way the industry views and analyzes RF data.
-
Product
RF Down-Converter
CDC100A
-
Systems Engineering & Management Company
The CDC100A Series Down-Converter is a 1U rack-mount device designed for use with antennas that have a Tri-Band Feed. The CDCMA100 Series Down-Converter is a synthesized down-converter supporting 1415-1585 MHz, 1650-1850 MHz, 2185-2485 MHz and 4400-5250 MHz, down-converting 4400-5250 MHz to 1415-2485 MHz. The CDC100A is provided as a 1U Expansion Chassis that communicates with any SEMCO receiver via an RS-485 protocol. The communications I/O is via RJ45 and the operator interface is via the receiver RCMS GUI.
-
Product
Low Noise Amplifiers
-
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a wide range of applications but are primarily suited to communication systems including both Data-Link and Satellite Communications (Satcom) systems. Our new K-Band LNA operates over a 19.2 - 21.2 GHz with 1.3 dB Noise Figure at 25°C. It is configured with a waveguide input and 2.92 output connector all in a hermetic package.
-
Product
RF Filters
-
Raymond RF offers a complete line of RF filters ranging from 0.4A to 600A in both stand-alone and cabinet-mounted configurations for our QuietBoxes and Anechoic Chambers. Both styles of filters can be supplied with NPT pipe nipples and flange nuts for mounting directly on a QuietBox or Anechoic Chamber. Alternately, both styles of filters can be remotely mounted with shielded conduit running between the clean end of the filter and the QuietBox or Anechoic Chamber.
-
Product
RF Antennas
-
These antennas are specially designed for IoT devices, are easy to implement, and provide high efficiency and performance. RF antennas are available in several configurations, with options for the number and range of frequency bands, antenna construction, and RF connector mating interfaces.
-
-
Product
RF & ECM Test Set
MS 1109
-
The RF Tester is a computer-controlled system used to test the RF Unit, Logic Unit (ECM) and its modules.
-
Product
Low Noise Test Cables For N1413 With B2980 Series, 3m
N1427B
Coaxial Cable
The N1427B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It comes with a separate triaxial (special screw-type) female connector and a High Voltage BNC (special type) female connector. This allows terminal configuration to be converted to any other configuration. Therefore, custom test fixture can easily be constructed. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1427B to the B2985B/87B.
-
Product
RF Amplifiers Bias Controllers
-
RF amplifier bias controllers generate a regulated drain voltage and actively adjusts the gate voltage of an external amplifier to achieve constant bias current. It can be used to bias any enhancement and depletion type amplifier operating in Class-A regime with drain voltages (VDRAIN) as specified. These devices achieve excellent bias stability over supply, temperature and process variations, and eliminates the required calibration procedures used to prevent RF performance degradation due to such variations.
-
Product
"Standard" RF Low Pass Filters
-
Coaxial Dynamics "Standard" line of RF Low Pass Filters offers several models to choose from at CW power ratings of 100 watts and 200 watts. These filters cover operating frequencies from 88 MHz to 400 MHz with less than 0.5 dB insertion loss and attenuation levels of 40, 50 and 60 dB.
-
Product
75 Ohm BNC to BNC Cable Assembly
40-977-701-0.5m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
Particle Impact Noise Detector
BW-LPD-D4000
-
FREQUENCY: SINE WAVE 27Hz TO 265HzACCELERATION: 0 TO 20G PEAKSHAKER: 100 FORCE LBS 3/4" IN STROKE 75 IN PER/SEC VELOCITYAMPLIFIER: 250 WATTS MINIMUMD.U.T. WEIGHT: 300 GRAMS PRACTICAL LIMIT @ 20G
-
Product
RF Shielded Box
LTL A6001
-
LTL A6001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL A6001 RF shielded test enclosure can comfortably house the intermediate device on test.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
PC USB Noise & Vibration Measurement Systems
-
IEPE Sensor Based Measurement Systems, Charge Amplifier Based Measurement Systems, All-in-One Integrated Vibration Measurement Systems
-
Product
Pulse Function Arbitrary Noise Generator
81160A
Arbitrary Waveform Generator
Generation of 330-MHz pulses and 500-MHz function/arbitrary waveforms with a 2.5-GSa/s sample rate and 14-bit vertical resolution; Selectable crest factors for white Gaussian noise lets engineers determine how much distortion to apply to a device during stress testing to meet various serial bus standards; Glitch-free timing parameter changes allow engineers to change the frequency without drop-outs or glitches and enable continuous operation without rebooting or resetting the device under test; and Arbitrary bit patterns show capacitive load of the channels using simple pattern settings. Complex measurement setups are no longer necessary to test designs to their limits. Pulses 330 MHz, 500 MHz sine waves, 660 Mbit pattern
