10 Gigabit Ethernet
Ethernet transfer rate > 1.25 gigabits per second. Also known as: 10GE, 10GbE,10 GigE
-
product
Ethernet I/O Products
Our products are designed to cover the most common industry applications. Our full selection of analog, digital, and serial I/O products with Ethernet connectivity allows for easy, simple to use data acquisition and control. Configure an IP-address and quickly acquire and output data over your network.
-
product
PXI-8232, Gigabit Ethernet, IEEE 488 PXI GPIB Instrument Control Module
781753-01
Gigabit Ethernet, IEEE 488 PXI GPIB Instrument Control Module—The PXI‑8232 combines a high-performance GPIB controller and a Gigabit Ethernet port into a single-slot module. You can use this module to integrate non-PXI instruments into a PXI system. The PXI‑8232 takes advantage of the Intel 82540EM Gigabit Ethernet controller. The 1,000 Mbit/s Gigabit Ethernet transfer rate provides a substantial performance increase over the Fast Ethernet transfer rate while remaining compatible with 10BASE‑T and 100BASE‑TX Fast Ethernet networks. You also can use the Ethernet port on the PXI‑8232 as an EtherCAT master, which is programmed with the NI‑Industrial Communications for EtherCAT software in LabVIEW. This module includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Ethernet, GPIB And USB To Modbus RTU Interface Board
ICS's Model 9009 is a multi-interface board that allows Ethernet, GPIB or USB control of Modbus RTU devices. The Ethernet port has VXI-11 protocol for easy control by the following computer systems without special drivers: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX and Windows 2K or later Windows systems. VXI-11 is one of the 9009's Ethernet protocols. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product. See our extensive Application Notes or download our VXI-11Tutorial and the VXI-11 Specification for more information about the VXI-11 Standard.
-
product
Ethernet Digital Interface OEM Board
8063
* Same Digital IO lines as standard 8063. * Same data transfer capabilities as standard 8063 * Digital I/O uses high-density DC-62 connector.* Power connections via 2 screw terminal strip or solder pads.* User configured IDN message and webserver pages makes board respond as part of your system.* Use an ICS Wiring Kit to extend the Ethernet signal to a rear panel RJ45 jack.* Runs on 9 to 32 Vdc power.
-
product
PXI Solid State MUX, 10 bank, 16 channel
40-680-002
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
Ethernet Speed Test Solution
NET-BOX™
The NET- BOX is an optimized Quality of Experience (QoE) testing platform that offers a low cost, reliable, high performance FPGA-based alternative to expensive high-end laptops often used for enterprise and speed tests. With a multi-test port architecture, with four 1GE, one 2.5GE test and 4 Gbps full line rate capability, the NET-BOX can truly test the limits to verify Quality of Service (QoS) and assure QoE for the ever growing high-speed internet service at and beyond 1 Gbps.
-
product
VME64X 7U 10 slot no P0
101V64XM10-0620R
7U VME64x Backplane 10-slot w/o P0, compliant with ANSI/VITA 1.1-1997, VME extension, and VITA 1.7 Increased Current. The extra 1U provides room for extra power bugs or busbars. Includes termination passive inboard and daisy chain automatic active.
-
product
AC/DC Power Supply 10 W
CFM12S050
AC/DC power supply with 10 W from Cincon | input ranges 90 - 264 VAC | output 5 V | operates in temperature from -40 to +75 °C | according to EN60335-1 standards
-
product
Ethernet Network Recorder
NET/REC/002
Curtiss-Wright Defense Solutions
The NET/REC/002 is a stand-alone Ethernet network recorder. Incoming Ethernet frames are written to a SATA cartridge using a FAT32 file system. The NET/REC/002 can be configured via the Ethernet port. The START/STOP switch enables the initiating and terminating of recording, while the EVENT button enables the marking of key events during the recording process.
-
product
Adapter Plate, Allows 10 Module ITA To Accept 25 Module Enclosure
410112424
The Adapter Plate allows the user to use standard 25 module enclosures with the 10 module ITA. See enclosures in the 25 Module section for more options.
-
product
Passive Probe, 10:1, 150 MHz, 1.2 M
N2841A
The Keysight N2841A low-cost passive probe provides a 10:1 attenuation and features a high input resistance of 10 MΩ. The probe can be adjusted for low-frequency compensation and high-frequency compensation.
-
product
PXI 12-Slot BRIC Matrix, 110x16 1-Pole (10 sub-cards)
40-562B-321-110X16
The 40-562B-321-110X16 is a high density BRIC12 matrix module with a size of 110x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
Noise Figure Analyzer, Multi-touch, 10 MHz to 3.6 GHz
N8973B
The N8973B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8973B.
-
product
Signal, Contact, Receiver, TriPaddle, 10 Amp, 14-18 AWG
610110177
Primary mating contact 610110113. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 10 Amps Max. Continuous (14 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
42-205-008 (PXIe) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
Ethernet Communications
Campbell Scientific offers complete Ethernet connectivity solutions for our data acquisition needs. Data loggers are available with integrated Ethernet, as well as stand-alone Ethernet modules.
-
product
PXI 8 Slot BRIC 460x8 1-Pole Dual Analog Bus (10 sub-cards)
40-560A-121-460X8-M
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Comb Generator, 10 MHz to 67 GHz
U9391G
The Keysight Technologies, Inc. U9391G comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
AXIe High-Speed Digitizer/DAQ, 10-bit, 10 GS/s, DC to 2.5 GHz BW
M9710A
Based on the AXIe standard, the M9710A is a unique 10-bit high-speed digitizer, capturing signals from DC up to 2.5 GHz at 5 GS/s. It provides excellent measurement accuracy and high dynamic range across four phase-coherent channels within a single card. Optimized response allows few hundred picoseconds pulse analysis. Moreover, an interleaving option allows acquisition at 10 GS/s on two combined channels, keeping excellent measurement fidelity.
-
product
PXI 8-Slot BRIC Matrix, 110x16 2-Pole (10 sub-cards)
40-562B-122-110X16
The 40-562B-122-110X16 is a high density BRIC8 matrix module with a size of 110x16 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
Ethernet Switches
Choose Omega's industrial-grade Ethernet switches to facilitate reliable data transmission speeds. These switches can withstand extreme conditions.
-
product
Digitizer/Oscilloscopes for LAN Ethernet
Wuntronic Lan Ethernet Digitizers & Lan Oscilloscopes
-
product
Cable, 10 Pos Combicon to Pigtail, 2 Meters
190656-02
The SH10M-10F Cable, sometimes referred to as SH10F-P, connects C Series DAQ devices with a 10-pin screw terminal to open signal wires. The SH10M-10F Cable is offered in different lengths.
-
product
10 Internal Tooth Lock Washers for Chassis Slides
HW-55
Package of 100 No. 10 internal tooth lock washers for chassis slides and support angles.
-
product
10 PCS Deluxe Noid Light / IAC Kit
3610
Peaceful Thriving Enterprise Co Ltd
*Kit packs in a deluxe mold plastic case.*Set includes: 8 Noid lights for testing GM PFI, FORD TBI, GEO TBI, BOSCH 2, BOSCH PFI, GM TBI, GM SCPI and GM MULTEC 2.*One IAC signal test lights for GM 1982 or newer GM TBI and PFI fuel injection system, and one for GM Model 1987 or newer GM Model 700 TBI and PFI fuel injection system.
-
product
Industrial Ethernet Solutions
ADI Chronous™ is the leading portfolio of edge-to-enterprise Industrial Ethernet connectivity solutions, specifically designed to accelerate your path to Industry 4.0. ADI has leveraged its deep domain expertise and advanced technologies to connect the industrial devices and networks of the future. Our trusted solutions ensure your critical data is reliably delivered throughout your application, ensuring seamless connectivity and operational efficiency. ADI Chronous solutions stand up in the toughest, time-critical environments and opens the door to gigabit and 10BASE-T1L connectivity.
-
product
cDAQ-9189, 8-Slot, TSN-Enabled Ethernet CompactDAQ Chassis
785065-02
8-Slot, TSN-Enabled Ethernet CompactDAQ Chassis - The cDAQ-9189 is a CompactDAQ Ethernet chassis designed for distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. With this chassis, you can combine C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis provides precise, synchronized timing over the network using TSN, ideal for highly distributed measurements over long distances. The chassis has an integrated network switch for simple daisy-chaining. The chassis also has four 32-bit general-purpose counters/timers, accessible through a hardware-timed digital C Series module for applications that involve quadrature encoders, PWM, pulse train generation, and more.
-
product
Ethernet Gateway for Woodward Easygen Genset Controls and LS-5 And DTSC-200 Controls
ESENET
ESENET is an Ethernet gateway specifically designed to interfaceWoodward's Easygen series genset controls with Modbus/TCP networks. It interfaces via the load sharing CAN bus with the Woodward controls.
-
product
÷10 HiZ 500 MHz Passive Probe for WaveSufer 400 Series Oscilloscopes.
PP007-WS-1
The PP007 embodies leading technology in passive probe design. The small probe is optimized for maximum waveform fidelity, including high frequency signal components, in a rugged probe suitable for every day.The sharp probe tip* is spring loaded, allowing it to retract into the narrow probe head. The tip does not slip off the object being probed—important when probing small geometry surface-mounted components. Probing dense circuits is easier with the small 2.5 mm ground sleeve, which provides much better visibility than 5 mm and 3.5 mm probes.
-
product
cDAQ-9191, 1‑Slot, Ethernet and 802.11 Wi‑Fi CompactDAQ Chassis
781497-01
1‑Slot, Ethernet and 802.11 Wi‑Fi CompactDAQ Chassis - The cDAQ‑9191 is a Wi‑Fi chassis designed for small, remote, or distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. You can send data from the cDAQ‑9191 to a host PC over Ethernet or IEEE 802.11 Wi‑Fi. The chassis also has four 32‑bit general‑purpose counters/timers built in. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
