Laser Test
-
Product
Environmental Control System Test Platform
Test Platform
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
Product
Generator/Analyzer for NFC/EMVCo Manufacturing Test
Micropross MP500 PT1-NFC
test
Support for ISO 14443 A/B, ISO 15693, MIFARE™, FeliCa™. Measurement correlation with NFC Forum and EMVCo certification test bench. Automated test executive with ready-to-run test sequences. Reader/Writer and Card Emulation modes, resonance frequency measurements supported on same antenna. Embedded analog measurements - LMA, field strength, S11, Q factor, waveform characteristics. Physical parameter/waveshape characteristic definition
-
Product
HTOL Test Systems
Test System
Our IOL & Power-Cycling systems increase measurement quality & throughput while simultaneously reducing the Total Cost of Test (TCoT) of an open platform. We focus on complete monitoring and precise temperature control for each device under test.
-
Product
RSE Wireless EMC Spurious Emission
TS8996
Test System
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
Product
Parallel Electrode SMD Test Fixture
16192A
Test Fixture
The 16192A test fixture is designed for impedance evaluations of side electrode SMD components. The minimum SMD size that this fixture is adapted to evaluate is 1(L)[mm].
-
Product
Application Software for Electronic Test & Instrumentation
test
Application software provides configuration-based workflows for electronic test and instrumentation applications. Application software is part of the NI software portfolio.
-
Product
Interactive Benchtop Test
test
Strict time-to-market deadlines make it vital to efficiently debug and validate product designs. Virtual instrumentation provides a unified interface that gives engineers an advantage over traditional box instruments.
-
Product
6TL24 Combinational Base Test Platform
H71002400
Test Platform
The 6TL24 is the Base platform ideal for Combinational test (ICT+FCT) in low to mid volume, high-mix electronics productions. A dual-stage pushing mechanism will allow performing both, the FCT and the ICT test, without the need of changing the test platform and with a low cost fixturing technology. To do so, the exchangeable cassette fixture must be designed with two-level probes. IN the 6TL24, the second level is reached thanks to a pneumatic actuator.
-
Product
Isolated Digital I/O 60VDC, 150mA
OTP2 module no.186
Test Platform
The National Instruments PXI-6528, PCI-6528, and PXI-6529 Digital I/O Modules are isolated digital I/O interfaces for PCI and PXI. These modules can use inputs from NI 6528 and PXI 6529 devices to capture the status of sensors, actuators, and logic devices. NI 6528 devices have 24 SSR outputs for switching external devices with input currents up to 150 mA. The NI 6528 and PXI-6529 devices are suitable for a variety of applications, from automotive development and industrial factory automation to aerospace, laboratory research, and biomedical applications due to their high current handling capacity and isolation.
-
Product
NFC Conformance Test System
T3111S
Test System
The T3111S RIDER NFC Conformance Test System is the Keysight solution for RF Analog and Digital Protocol testing of NFC, EMV and ISO devices. The Test System is based on the Keysight T1141A NFC Test Set and it is complemented by the Keysight's or FIME's robots for accurate and repeatability RF testing. Selected 3rd party positioning robots can also be supported.
-
Product
Functional Test System Optimized For Real-Time Digital Bus Test
Spectrum HS
Test System
Spectrum HS is Teradyne’s fully integrated functional test system. Optimized for real-time test of low latency buses, it’s a high-performance system delivering excellent test coverage of current and future products.
-
Product
Batterie Inspektor
Battery Test Platform
By combining the most diverse hardware and software modules, Batterie Inspektor™ delivers innovative, automated, and digitalized battery testing at every stage of manufacturing. With this flexible test platform, all modules can be adapted to their respective quality requirements. Manufacturing is simplified through a scalable and standardized framework for both new projects and upgrades.
-
Product
Laser Diode Life Test
-
Life-tests consist of the highly accelerated ageing, under controlled conditions, of a group of lasers taken as a representative sample. Optical degradation of the laser diodes is observed and recorded by precisely measuring changes in the laser's operating characteristics during the test. Life-tests are used for vendor qualification of the laser diodes during product development and can be conducted throughout the production life of the laser.
-
Product
Build-to-Print for Test Systems
Test System
Built-to-print / test system replication addresses your internal capacity and capability constraints. Ball Systems has perfected quoting, procurement, planning, assembly, testing, quality, delivery and installation to ensure your testers are on-time and on-budget, and meet design and production standards while keeping open and transparent communication.
-
Product
LIV – High-power Laser Diode Testing
-
An important aspect of the development and manufacture of laser diodes is the so-called laser diode characterization, or laser IV curve. By applying increasing current to the laser diode so it that emits light, the optical output is measured together with the voltage drop across the diode element. The resulting LIV curve reveals important clues about the quality of manufacture and the performance of the laser diode, enabling a pass/fail decision to be met.
-
Product
Open Test Platform for High Performance Automotive Applications
TSVP
Test Platform
The R&S®TSVP family of products is an open test platform from Rohde & Schwarz ideal for high performance automated test equipment (ATE) applications. The chassis contains a mechanical frame, digital backplane, analog backplane, mains switching and filtering, power supply and diagnostic extensions. A highlight is the analog bus for routing measurement signals between different slots without additional external wiring.
-
Product
VLSI Test System
3380
Test System
The 3380 VSLI test system equipped with a maximum of 1280 I/O channels, 256 VI sources, flexable architecture and comprehensive optional function boards (ADDA/Hi-voltage DPS) can meet the high parallel multi-test tendency.
-
Product
Modular Functional Test Platform
LX-OTP2
Test Platform
The OTP² system platform has recently been available in both the PXI and LXI versions. The OTP2 system platform enables the cost-effective and fast implementation of function test systems based on defined modules and function blocks. Thanks to the open system interfaces, customer-specific adjustments can be made at any time without any problems. When considering options for your next generation functional test system, it is important to assess the entire life cycle of the system and the associated costs and efforts. Use OTP² to accelerate development cycles and reduce the development effort for new functional test systems.
-
Product
Test Fixture, Axial And Radial
16047A
Test Fixture
The 16047A is designed for impedance evaluation of axial/radial lead type devices of up to 13MHz. The 16047A employs Kelvin contacts which realize a wide impedance measurement range. The contact tip can be changed according to the device shape.
-
Product
PCI Express 5.0 Test Platform
Test Platform
Teledyne LeCroy’s PCI Express 5.0 Test Platform is part of a suite of tools that facilitates complete protocol testing of PCI Express devices up to and including version 5.0. The latest feature of the Teledyne LeCroy Test Platform is the addition of an integrated interposer, which eliminates the need for an external interposer. This innovation simplifies setup with fewer connection points and outboard devices, making analysis easier and more reliable than ever. In addition to using the Test Platform with the Exerciser, the user can connect two of their own devices and use the Test Platform as a PCIe 5.0 backplane and as an interposer to capture protocol traffic between the systems.
-
Product
Laser Source
TW3111
-
Techwin(China) Industry Co., Ltd
Laser Source TW3111 is a handheld optical light source, newly released in 2007. It can provide 1 to 6 wavelengths output to satisfy specific requirements including the 650nm visible light source and the 1310/1550nm wavelengths for single mode fiber or the 850/1300nm wavelengths for multimode fiber, as well as other wavelengths according to customer's needs. Together with the TW3211 optical power meter, it is a perfect solution for fiber optic network applications.
-
Product
Laser Diode Characterization Testing
-
The Yelo Laser Diode Characterization system performs automated characterization of a laser device. The system will allow the operator to load a single packaged Laser device into a TEC controlled fixture mount. Each test station (LIV, Spectrum, Far Field/Beam Divergence) will then automatically align with the Laser Device in a sequential order and perform the automated tests required of each station.
-
Product
In-line High-Density ICT System Series 7i
E9988GL
In-Circuit Test System
The E9988GL Keysight i3070 Series 7i Inline High-Density In-Circuit Test (ICT) system brings industry-leading ICT technologies into your automated manufacturing line, saving resources and optimizing your automated test strategy.
-
Product
Laser Photometer
8587A
-
The photometer owners asked TSI to develop a modern version of the Laser Photometer 8587 that retains data continuity with the original version. Without data continuity, vast amounts of legacy research would not be directly comparable to new research. The result was the Laser Photometer 8587A.
-
Product
Laser Head
5517D
-
The Keysight 5517D is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Please contact Keysight for custom requirements.
-
Product
Laser Trackers
Radian Series
-
The smallest, lightest, most accurate laser measurement tool. API’s compact and rigid UNIBODY tracker design allows for shaft mounted motors, encoders and laser. The UNIBODY shaft mounted laser innovation minimizes Abbe offset errors, while also housing laser source, optics, camera and major head electronics in the center of the tracker body.
-
Product
Laser Diode Burn-in Reliability Test System
58604
Test System
The Chroma 58604 is a high density, multi-function, and temperature controlled module for laser diode burn-in and lifetime tests. Each module has up to 256 SMU channels which can source current and measure voltage in various control modes as described below.
-
Product
Picosecond Laser
PIXEA
-
The PIXEA is a high-quality laser system for OEM and R&D applications generating ultra-short optical pulses by using gain-switched laser diode technologies. The laser features high-quality picosecond laser pulses with no satellite pulses and minimize pulse tail. The PIXEA series offer a large variety of centered wavelengths between 375 nm and 2 um. The pulse duration down to 20 ps is optimized for each wavelength. The system is based in two modules or one module, the laser head and the dedicated Control Unit including the GUI software. Different optical output options are available, including free space collimating optics and fiber coupled.
-
Product
Laser Optics
-
A substrate is developed into a laser optic when it is refined with a dielectric coating. Due to the wide range of possible combinations between the substrate and the coating, one optic seldom resembles another. Contact us directly and together we can design a product to adequately suit your needs.
-
Product
3-Axis Non-Robotic Automated Testing System
AT3
Test Instrument
The Instron AT3 is a space-efficient, highly adaptable 3-axis mechanical testing platform designed for automated execution of tensile, compression, flexural, and lap shear tests. Built to comply with a broad spectrum of ASTM and ISO standards, it’s well-suited for evaluating materials such as plastics, elastomers, thin films, foils, and metals. The system streamlines the entire testing workflow from specimen measurement and handling to strain measurement and specimen disposal—enabling users to load up to 160 samples and let the AT3 take care of the rest. Boost productivity, reduce manual intervention, and achieve consistent, dependable results with every test cycle.
