TWT Amplifiers
generate high power RF signals. Also known as: Traveling Wave Tube Amplifiers, TWTA
See Also: Microwave Amplifiers, Traveling Wave Tube Amplifiers, TWTA
-
Product
Amplified Photodetectors
-
Hinds Instruments' photodetector modules are specifically designed for use with high frequency optical signals including those generated in Photoelastic Modulator (PEM) applications.
-
Product
Full W-Band Power Amplifier
SBP-7531142515-1010-E1
-
For communication and radar applications, SAGE Millimeter has released a new full W-Band power amplifier. Model SBP-7531142515-1010-E1 is a power amplifier with a typical small signal gain of 25 dB and a nominal output power of +15 dBm across the frequency range of 75 to 110 GHz. The DC power requirement for the amplifier is +15 VDC/190 mA. The mechanical configuration offers an in-line structure with WR-10 waveguides and UG-387/U-M flanges. Other port configurations, such as with 1 mm connectors or a right angle structure with WR-10 waveguides, are also available under different model numbers. Features include: Full Band, High Gain, High Output Power.
-
Product
Variable Gain Amplifiers
-
50 dB Gain, 14 dBm P1dB, 100 MHz to 18 GHz, Rack Mount, Variable Gain Amplifier, 6.5 dB NF, SMA
-
Product
HF Amplifier
-
bsw TestSystems & Consulting AG
Whether a HF amplifier which is mounted in a 19" rack is viewed as an instrument, a system or a component largely depends on the point of view of the application developer. We list this product family here; however we would like to point out that our 19" amplifiers for rack-mount and benchtop applications, as well as modules without power supply, are listed in the "Components" section.
-
Product
Third Party RF Amplifiers
-
We work closely with major manufacturers to supply a range of oscilloscopes, function generators and power amplifiers. We are the UK agent for the leading manufacturer of RF amplifiers Electronics and Innovation.
-
Product
Ground-Based Satcom Amplifiers, Modems & More
-
Modems for Small-to-Medium Sized Networks Where Security is of Utmost Importance.
-
Product
High Voltage Op Amplifiers ≥12V
-
High supply voltage op amps are used in systems that demand the widest dynamic range with the best signal-to-noise ratio. Engineers turn to Analog Devices for high voltage amplifiers that deliver industry-leading performance. Increasingly, new high voltage amplifiers also offer features to improve system performance, cost, and robustness while easing the complexity of system design. New features include integrated input overvoltage protection (OVP), on-chip electromagnetic interference (EMI) filtering, higher electrostatic discharge (ESD) immunity, and greater resistance to latch-up in both powered and unpowered operations.
-
Product
VME PWM Servo Motor Driver / Amplifier Board
64PW2
Servo Motor Drive
NAI’s 64PW2 is a 6U VME Servo Motor Driver/Amplifier Board featuring a dual, four-quadrant, bi-directional, PWM servo amplifier. Specifically targeted for DC servo motor applications, this board has an amplified power stage that uses a Pulse Width Modulation (PWM) control signal to provide motor control for both brush and brushless motors. Each motor drive accepts a 65 VDC power input and provides a 5 Amp maximum continuous current output (8.5 Amp peak).
-
Product
Reference plus Comparator or Amplifier
-
Analog Devices reference plus comparator or amplifier products combine the excellent initial accuracy and low overtemperature drift performance of single function voltage references with comparators, buffer amplifiers, and current sense amplifiers. These products offer compact solutions for a broad range of applications such as battery monitoring, threshold detectors, window comparators, auto power-off circuits, and low dropout (LDO) regulators.
-
Product
Composite 1×24 Video Distribution Amplifier
VDA124RM-12
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Amplifiers
-
Fully automatic, legal limit plus headroom amplifierAlpha’s low-drive, tube amplifier design delivers the cleanest possible signalOperates on all Amateur Radio Bands 160M thru 10MSingle, easy to find, inexpensive 3CX1500A7 8877 type tubeInternal, automatic 4 port antenna switch capable of combining any 2 antenna portsAlpha’s Legendary service and support4 year limited warranty on hardware, 1 year on tube1500W, 100% duty cycle, no time limitation, key down foreverRugged construction built to last
-
Product
Low Noise Op Amplifiers (≤ 10nV/√Hz)
-
Analog Devices’ portfolio of low noise (≤ 10nV/√Hz) op amps includes many amps with the lowest noise performance in the industry. These high speed, low distortion (1 nV or less) op amps enable better signal fidelity in the most demanding conditions, allowing system designers to achieve the lowest total system noise performance in applications with high source impedances. We feature a considerable variety of these amps with wide supply ranges and low power.
-
Product
IRIG Amplitude Modulated Time Code Distribution Amplifier
1205A / 1205A-MC
-
Precise Time and Frequency, Inc.
The ptf 1205A is a 12-channel IRIG amplitude modulated time code distribution amplifier housed in a 1U high, 19″ rack package. The ptf 1205A uses an RF design combining the latest technology in low noise components to minimize input/output delays which are of the order of nano seconds.The unit uses two stages of input signal buffering to distribute the input signal to 12 separate outputs, and insure maximum isolation between individual output signals.
-
Product
20GHz 30dBm RF Signal Amplifier
A10200
-
Model A10200 is an ultra-small footprint, ultra wideband, high power amplifier designed for high frequency, high power, signal amplification. With an ultra high bandwidth of almost 20GHz and up to +28dBm power into 50 ohms, the A10200 is the ideal complimentary amplifier to any signal source that needs an extended power boost for demanding applications.
-
Product
Power Amplifiers
Immunity
-
The RF power amplifier range from Laplace is specifically designed for EMC Immunity testing according to IEC61000-4-3 and IEC61000-4-6. These are compact units with characteristics matched to the requirements of IEC standards. These RF amplifiers utilize fully isolated linear MOSFET or advanced GaAs FET devices, which provide high gain, wide dynamic range and excellent third order intercepts. High efficiency and reliable operation are achieved by employing unique RF combining circuits, RF microstrip networks, sophisticated thermal design, custom machined housing and heavy duty components. The high power RF amplifiers undergo extensive burn-in prior to final test and inspection.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
-
Product
DSP And Power Amplifier
DMPA12
-
The DMPA12 is a powerful digital audio processor and multi-channel power amplifier combined into a single rack space component designed to work with DM Series processors. The design represents a milestone in DSP technology in its basic architecture and in its processing speed and efficiency. The primary applications are sound reinforcement and teleconferencing in boardrooms, courtrooms, worship centers, distance learning systems, hotels and other applications with multiple microphones and loudspeakers. The design is ideally suited to mix-minus sound reinforcement systems.
-
Product
High Power RF Amplifiers
-
Corry Micronics' line of high power RF amplifiers feature up to 40% efficiency. an extended temperature range of -30 degC to 55 degC for MIL-STD applications, and status monitoring signals that provide diagnostic information.
-
Product
High-Voltage Amplifiers
-
Power amplifiers are a must in applications requiring both complex signals as well as high voltage throughput. However, this is uncommon in high performance instrumentation, therefore an external amplification device must be used. In these cases, a high voltage amplifier is used to increase the size of a signal by some factor.
-
Product
DIO-AIO Conversion Set For Conventional Power Amplifier
PAD64
-
PAD64 DIO(digital input/output)-AIO(analog input/output) Converter is the equipment which could be used for DI/DO (Digital input/Digital output) conversion and galvanic isolation between Real-time simulation system and protection equipment, and any other equipment which need AIO (analog binary input/ output, dry contacts).
-
Product
HDMI Audio Extractor with Audio Amplifier, RS-232 and IP Control
EMX-I-AMP
-
The EMX-AMP is a 4K HDMI Audio Extractor with built-in 50 watt audio amplifier for direct connection of 8 ohm speakers. The device also provides line-level stereo Aux audio input and allows audio mixing of HDMI audio with the Aux input. Volume can be controlled from the front panel, RS-232, or external digital rotary pot (encoder) that can be mounted on a wall-plate.
-
Product
Broadband Power Amplifier
PAS-00023-25
-
* Solid State Power Amplifier* Gain : 46 dB typ.* High IP3, 48.0 dBm typ.* Bench Top Case* Internal Cooling Fans* Over Temperature Protection* Type N Connectors
-
Product
Ka Band Power Amplifier
-
The ERZ-HPA-2000-4500-24 is a Ka Band Amplifier providing an output power of 24 and a gain of 22 dB. The compact size and modularity makes it ideal for a wide range of applications. Frequency Range (GHz): 20,00 to 45,00.
-
Product
Low Noise High Precision High Voltage Amplifier
WMA-280
-
The WMA-280 is a high voltage, low noise precision amplifier. Its specifications have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-280 can be used for MEMS actuation, EO-modulators, as high voltage driver for PZT (piezo) positioners, ultrasonics, and many other applications. Its output noise is only 300 microVolt rms.
-
Product
Composite 1×24 Video Distribution Amplifier Board
BL-VDA124-01
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Amplifiers - Solid State
-
PMI offers a full line of RF and Microwave Amplifiers that range from 250 kHz up to 50.0 GHz. Many options are available. If you do not see exactly what you require on this website, please contact sales@pmi-rf.com because we offer amplifiers designed and built to your specifications at catalog prices.
-
Product
Instrumentation Amplifiers
-
Analog Devices instrumentation amplifiers (in-amps) are precision gain blocks that have a differential input and an output that may be differential or single-ended with respect to a reference terminal. These devices amplify the difference between two input signal voltages while rejecting any signals that are common to both inputs. The in-amps are widely used in many industrial, measurement, data acquisition, and medical applications where dc precision and gain accuracy must be maintained within a noisy environment, and where large common-mode signals (usually at the ac power line frequency) are present.
-
Product
WaveLink ProBus2 Platform/Cable Assembly for 4-8 GHz WaveLink Amplifiers.
WL-PBUS2
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Power Amplifier
MS 2011
-
Power Amplifier is used to amplify the RF signals from low power to 100 Watts of RF carrier power to 400 Watts Peak envelop power (single side band operation). Outputs are filtered. This system is controlled through microprocessor and it has RS485 interface.
