Contacts
See Also: Modules, Wire, Connectors, Patchcords, Flying Leads
-
Product
Power and Signal Twist Capsules
-
Power and Signal Twist Capsules are used when only limited rotating is required and/or sliding contacts cannot be tolerated.
-
Product
Signal, Contact, Receiver, TriPaddle, 7 Amp, 26-28 AWG
610110167
-
Primary mating contact 610110169. (May mate with other ITA contacts, as well.)
-
Product
Infrared Thermometer Calibration
-
Nagman Instruments & Electronics Pvt. Ltd
Nagman’s Infrared thermometers Calibration Instrument can be used for hassle free temperature measurements as they work on non- contact principles. You can stay at a safe distance from the temperature source and still find accurate readings by pointing IR thermometer at the source. These also have a digital display of the temperature readings and hence, any and all manual errors can be avoided.
-
Product
20-Pin GMCT Male Connector, 10A, With Backshell
40-960-020-10A-M
-
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 16 AWG. Also included is the backshell with screwlocks and cable clamp.
-
Product
Digital Input/Output Expander (Open-Collector Outputs)
ENVIROMUX-DI16DO16
-
Adds 16 digital inputs and 16 digital open-collector outputs to the ENVIROMUX-2D/5D/16D. Interfaces with the ENVIROMUX-2D/5D/16D via the RJ45 Sensor Port. Digital inputs: 16 screw terminal pairs for connecting dry contact devices; One screw terminal pair for tachometer; 0 to 255 Hz. Accepts 26 to 16AWG wire. Potential free. Voltage range: 0 to +36VDC. Over-voltage surge protected. Digital outputs: 16 screw terminal pairs for open-collector outputs. Accepts 26 to 16AWG wire. Rated sink current: 500 mA per output. +5VDC, 22kΩ pull-ups. Voltage range: 0 to +24VDC. Over-voltage surge protected. Supports CAT5/5e/6 cable up to 500 ft. (152.4 m). Powered by ENVIROMUX-2D/5D/16D. Compatible with ENVIROMUX-2D/5D/16D. Dimensions WxDxH: 6.49x3.10x1.08 in (165x79x27 mm). Regulatory approvals: RoHS.
-
Product
Mini Coax, Module, Receiver, 90 Series, 37 Position
510104301
-
Primary mating module 510108276.*Please note: VPC receiver modules must be separated into two pieces in order to extract contacts. For detailed instructions please consult the user manual/procedure sheet for this module before extracting contacts.
-
Product
500-Pin SEARAY Connector, Male With Backshell, 2 Amp, 250 Port
C500RMR-4SB-4B
-
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This accessory is designed to allow users to directly terminate a cable via solder bucket connections to a PCB linked to a 500-Pin SEARAY connector. Pickering Interfaces recommend the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Coax, Module, Receiver, 20/26 GHz, 90 Series, 17 position, incl. strain relief plate
510104287
-
Coax, Module, Receiver, 20/26 GHz/75 Ohm HD, 90 Series, 17 position, incl. strain relief plate(For use w/ 20/26 GHz contacts & SMA adapter. Includes strain relief plate) Primary mating module 510108240.*Please note: VPC receiver modules must be separated into two pieces in order to extract contacts. For detailed instructions please consult the user manual/procedure sheet for this module before extracting contacts.
-
Product
Extender
3690-3
-
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
Product
Pod with Four Test Access Ports for 5v or 3.3V TTL Thresholds
JT 2137
-
The JT 2137 pod remains a popular choice for DataBlaster controller installations that require a compact signal conditioning pod embedded within a test fixture. The JT 2137 features four test access ports which together may be set for 5v or 3.3V TTL thresholds, although additional plug-in adapters are available that allow alternative thresholds to be set on a TAP by TAP basis (contact your local sales office for details). The 20-way 0.1″ IDC TAP headers comply with the standard JTAG Technologies 20-way pin-out and provide the additional flash programming controls Read/Busy and AutoWrite.
-
Product
Connectors
-
Through our Hypertac, IDI and Sabritec technology brands, we supply application-specific, high-reliability electrical interconnect solutions from highly integrated assemblies to microminiature connectors and spring probe contacts. The core of our advanced interconnect solutions is our contact technologies: Hyperboloid, Tortac, Spring Probe, High Speed, Edge Card, Fiber Optic, EMI/EMP, High Power and High Temperature.
-
Product
160 Pin Female LFH to QuadraPaddle Flying Lead Cable, 60", 780009-02
VFL159124-060
-
Vendor Flying Lead (VFL) Cable, 160 Pin Female LFH to QuadraPaddle Leads, 28AWG Twisted Pair, 160 T/P's, SHARED GROUNDS 80 T/Ps, 168 connection points, CONN: 780009-02, VPC Contact 610138216 - QP RCV (22AWG-28AWG) (5 AMP/25 mΩ MAX), 60" length.
-
Product
Network OTDR
NFO series
-
The NFO OTDR unit injects the laser pulse into the fiber under test and picks up scattered and reflected optical signals by an avalanche photodiode (APD). The unit accepts remote commands from Internet to control all related timing and data acquisition processes. Maximal three wavelengths are available at the NFO with options on 1310, 1490, 1550, and 1625 nm. NFO also has options on dynamic ranges so users can select the most cost effective units for their demands. Radiantech provides an easy use API (Application Program Interface) for NFO so users can design and build their own AP for NFO. Standard NFO API package is for Windows XP or higher. Please contact Radiantech’s sales person to inquire API for another OS.
-
Product
Coaxlink Duo PCIe/104-MIL
-
Ruggedized COTS board for military applicationsSale subject to approval and export license. Please contact us for more informationSmall stackable PCIe/104 form factorExtended temperature range: -40 to +85°C / -40 to +185°FMIL-STD-810G method 514.6 (vibration) and method 516.6 (shock)Optional conformal coatingTwo CoaXPress CXP-6 connections: 1,250 MB/s camera bandwidthPCIe 2.0 (Gen 2) x4 bus: 1,700 MB/s delivery bandwidth
-
Product
Contacting Single-turn
-
A rotary position sensor translates angular mechanical position to an electrical signal. Rotary position sensors are designed for applications that typically require frequent adjustments. Shaftless designs allow for different engagement mechanisms, such as a customized shaft, a motor control, a human interface adjustment or a mechanical arm position locator.
-
Product
IULTCS Rubbing Fastness Tester
TF414
-
TESTEX Testing Equipment Systems Ltd.
Rubbing Fastness Tester, to determine the color fastness to rubbing. IULTCS Rubbing fastness Tester complies with ISO11640, EN 344, SATRA PM 173, etc. You can contact us if you have any problems when you do rubbing fastness test.
-
Product
Three-Phase Transformer Winding Resistance Meters
TWA Advanced Series
-
TWA Advanced series is the latest DV Power solution for three-phase transformer winding resistance measurement and tap changer analysis. They are capable of testing six transformer windings with a single cable connection, as well as three-phase automatic transformer demagnetization. It has the option of the automated test mode, where the instrument operates the tap changer without operator input (minimizing the risk of human error) and records winding resistance results based on pre-selected stabilization criteria.The unique DVtest method of tap changer analysis enables checking the moving contacts of on-load tap changers during the transition, measuring the transition time, detecting open circuits, and many other types of faults. It is performed with 0.1 ms sampling rate, together with the measurement of tap changer motor current which detects motor and mechanical issues. A special proprietary algorithm is used for testing tap changers connected through a built-in series (booster) transformer. The DVtest can be performed either on one phase or simultaneously on three phases. It can also be performed together with the winding resistance test in all tap positions.A unique advantage of TWA Advanced instruments is the capability of simultaneously testing the winding resistance of all three phases of a three-phase transformer connected in a YN configuration. This can significantly speed up the testing– for example, it enables the operator to perform 33 measurements instead of 99 on a tap changer with 33 tap positions.TWA500 is equipped with a large 10.1” graphical touch-screen display, while TWA400 has a 7” graphical touch-screen display. Besides making the interface much more user-friendly compared to older winding ohmmeters, it also enables certain test options that were previously available only with DV-Win software. The most important among them are DVtest, tap changer motor current measurement, “Heat Run” test, test templates, and automatic test mode.
-
Product
Signal, Module, ITA, TriPaddle, 90 Series, 64 Position, with Right Angle Contacts
510108112
-
Primary mating module 510104134. (May mate with other Receiver modules, as well.)
-
Product
Test Finger Probe
-
Shenzhen Bonad Instrument Co., Ltd.
BONAD’s test fingers, test probes and test needles comply with IEC 60065, IEC 60238, IEC 60335, IEC 60529 and IEC 61032 standards and are essential instruments for the protection against electric shock of household and similar electrical appliances. For more information, please contact us and BONAD will provide you with professional technical advice and high-quality testing equipment.
-
Product
Certified Sanitary Inline Refractometer | 2″ Tri-Clamp
VIP2-3A
-
3-A Sanitary Refractometer for Food & Product Safety: Driven by concerns over food and product safety in the dairy, food, beverage, and bio-pharmaceutical industries, 3-A certified sanitary refractometers must meet exacting hygienic standards before they are awarded certification, one of the top honors attainable in the field of refractometry. Needless to say, refractometers carrying the 3-A seal meet the highest level of professional standards for the protection of public health by offering the maximum degree of protection against food or product contamination, resulting in product contact surfaces that can be easily cleaned and sanitized.
-
Product
Microscopes
-
A digital or traditional optical microscope can help engineers check on their high-speed probing activities much more easily. It will assure the probe tips will touch on the right contact(s), with correct contact angle and right amount of force. We use both digital and optical microscopes in our own lab. The information in this page is to help you choose a microscope best suits you.
-
Product
Circuit Breaker Testing Equipment (SCOT Series)
SCOT M3K
-
SCOT M3K measures and displays CLOSE, OPEN and CLOSE-OPEN time of main contacts of 3 poles connected end to end, simultaneously.
-
Product
Combinated Thermometers
-
PeakTech Prüf- und Messtechnik GmbH
Professional "5 in 1" environmental video measuring device with a dual laser for exact target area determination for fast, accurate and non-contact surface temperature measurements. An additional type K measurement input is available on the device for direct contact measurements or differential measurements of surfaces. The integrated photo function displays the measured object with the temperature displayed and other measurement data such as air humidity and dew point temperature and can be saved in the internal memory or on a microSD card. The integrated data logger saves all measured values which can be evaluated and processed on the PC. Ideal for documenting important measurements in the industrial sector, electrical engineering, maintenance and service work, quality assurance, construction and energy consulting.
-
Product
Relays
-
Mitsubishi Electric Automation, Inc
Mitsubishi Electric offers AC and DC controlled Contactor Relays with multiple open and closed contacts configurations that can be used in a variety of applications; alarms and sensors, signal switching, detecting and controlling faults that occur in electrical circuits.
-
Product
48-Channel VME Isolated Digital Input Module
V280
-
The V280 is a single-wide, 6U VME module that includes 48 isolated logic inputs. It is available in versions for nominal 5 volt or 24 volt input levels. The V280 has independently programmable rising and falling edge response times to support contact debounce, glitch catching, and DC or AC inputs.
-
Product
Elevator Strip-Line™ Socket with Bifurcated Contacts
Series 700
-
Elevator Strip-Line Sockets with Bifurcated Contacts. Features: For elevated mounting of LCDs and other odd-centered or high pin count components. Any height from .360 to 2.000 [9.14 to 50.80]. ?Optional spacer available for mounting on .300 [7.62], .600 [15.24], .900 [22.86], 1.100 [27.94], and 1.300 [33.02] centers. Consult factory for other sizes.
-
Product
6-24V Car Circuit Tester
1952
-
Peaceful Thriving Enterprise Co Ltd
Check on 6-24V system. The alligator (earth) clip is suitable for earth and the tip of the contact probe is placed onto the part to be used. If current is present the test light will glow.
-
Product
Protective Cover, G6, Receiver
310113158
-
The Receiver Protective Cover is optional to keep your modules and contacts enclosed when the Receiver is not in use.
-
Product
Cantilever Probe Cards
-
Cantilever Probe Cards are based on the approved epoxy ring design. The probe-needles are precisely arranged the required pattern to ensure proper contact on the pads.
-
Product
Ground Fault Protection Monitors
-
The Earth Fault Resistance Monitor (EFREM) and the Rotor Health Monitor (RHM) provide wireless rotor ground fault and temperature monitoring for generators and motors. The systems replace older slip ring contact ground fault detectors on any synchronous generator or motor.
