Locators
are used to find or position.
-
product
Universal Copper Qualifier
ELQ 30A+
200 Hz to 35 MHz selective/wideband Level Meter & Generator, with Spectrum Analyser with Z/RL/LCL and Fault Locator Bridge
-
product
Electrostatic Field Meter - Hand Held Field Meter for Locating and Measuring Electrostatic Field Density
PFM-711B
- Lightweight, portable, hand-held Field Meter- Measure in 1 volt/in increments 0 to ±1,999 Volts- Measure in 10 V/in increments 0 to ±20,000 VoltsAccuracy of <±5%- LED ranging lights help position the meter at the right distance- Zero button allows the display to be adjusted to zero (0)- Hold feature freezes the measurement on the display- Use with Prostat CPM-720B Charge Plate Monitor and PCS-730B Electrostatic Charger- Use with Prostat PGA-710B AutoAnalysis System or X-Y Plotter- Analyze Footwear/Flooring Combinations- Verify Ionizer Balance and Decay Time Performance- 2-year Limited Warranty (1 year on the sensor)
-
product
Rotary Thermal Shock Chambers
TS Series
A Bemco exclusive product, the TS Series of Turboshock Rotary Thermal Shock Chambers feature an electrically driven, 180 degree reversing, rotating wall located between two chambers, one hot and one cold. Two loads can be handled simultaneously. Front loading and rear access doors allow full entry to each zone.
-
product
Mobile Cable Fault Location System
BAUR Syscompact 4000
BAUR Prüf- und Messtechnik GmbH
Fault location with Syscompact 4000. The Syscompact 4000 is a compact, fully enclosed fault location system for pre-location and pinpointing of high-resistive, low-resistive and intermittent faults on low- and medium-voltage cables. Easy operation and the use of latest fault location methods enable fast and safe fault location.* Location of low-resistive, high-resistive and intermittent cable faults* Efficient cable fault pre-location methods* Pinpointing according to the noise location method or acoustic propagation time measurement* (with Universal Locator and ground microphone)* Sheath fault location according to the step voltage method (with Universal Locator and two measurement probes)* Easy to handle
-
product
Automatic Meter Reading Unit
Signals & Systems India Private Limited
SANDS make of AMR Modem SAM-1101 is a smart electricity meter reading device that can be connected to any make of electronic energy meter by means of optical/ RS232 port, which is compliant to DLMS – IEC 62056-21 standard. The electricity meters measuring energy consumption can be located in either consumer premises or in distribution transformers. The modem draws its power from the meter terminal block and connects to the communication port of the meter. Thus this add-on energy meter reading system is non-intrusive and can be retrofitted easily to any meter. The Electricity Meter Reading device uses GSM/GPRS communication technology and has built-in intelligence to talk to the DLMS meter. AMR system is compatible with 4G network to push the power consumption-billing data, load survey data, and event data to a cloud-based server, with fallback options to 3G & 2G.
-
product
Wall Searching Metal Detector
HHB C
A Wall Searching Metal Detector, also known as a stud finder or wall scanner, is a tool used to locate hidden objects behind walls, such as metal pipes, electrical wires, and wooden studs.
-
product
Health Physics Systems
Detection and quantification of radioactive material within the body is a key factor in determining internal personnel contamination and dose assessment. These measurements can be made on body fluid samples using lab instrumentation or through direct measurement of personnel. The measurement of body fluids is generally less attractive due to the bio-hazards and lack of immediate results unless non-gamma emitting nuclide measurements are required. The direct measurement of personnel for gamma emitting radioactive material provides rapid results, can determine where the material may be located within the body, and does not require mobility of the material through body fluids for detection.
-
product
AMP HOUND 2
AMP2
*Attach adapter to fuse or touch probes to top of the fuse to measure automotive amperage instantly without removing the fuse*Audible tone lets you know when you have connection with a fuse and if there is current present in the circuit; perfect for working on under-the-dash fuse boxes*Snapshot Mode and Tracking Mode allow easy component testing and parasitic drain location
-
-
product
Tool, Locator, Micro Coax, Receiver
910101135
Included with Crimp tool kit p/n 910101132 and kit p/n 910101131.
-
product
Portable Spectrophotometers
Konica Minolta Sensing Americas, Inc
Konica Minolta’s expansive range of handheld portable spectrophotometers is compact and lightweight. They come with color LCD screens that allow accurate, portable color measurement in various locations. Their ergonomic design gives high-performance quality control while still being easy to maneuver.
-
product
Portable GIS Partial Discharge Detector
JHPD-10
Xiamen Jiahua Electrical Technology Co.,Ltd
JHPD-10 quickly and accurately detects various kinds of partial discharge signals that occur with insulation defects in GIS. Attached on the surface of GIS the detector collects the inside discharge signal of impure gas, suspension potential and solid insulation material. The diagnostic software analyzes the fault character and locates the fault to avoid electricity accident. The device is for daily patrol inspection with high efficiency and easy operation features. Designed with two UHF signal channels, one detects the partial discharge signal; another excludes the disturbance signal like corona discharge in the air and mobile phone communication.
-
product
Calibration Lead Precision Resistor - Single
40-975-009-SL1
The cable assembly is specifically designed to connect to the 9-Pin D-Type calibration port located on the front panel of Pickering Interfaces Module Part Numbers 40-260, 40-261, 40-262, 40-263 and 40-265.
-
product
Bond Testing
Our complete line of bond testing (BT) flaw detectors provides unmatched capabilities for the location of discontinuities and other flaws in composite structures. We offer a wide range of measurement features and application-specific options for flaw detection.
-
product
2-port Battery Portable Passive Intermodulation Analyzer - iXA Series
iXA
The Kaelus iXA Series Passive Intermodulation (PIM) analyzer is a dual-port, battery powered PIM Test Analyzer. It supports multiple test scenarios such as testing at the top of the tower, the base of the tower, rooftop, in-building for DAS systems and external PIM Finding.No other PIM tester has ever been integrated to this level! The iXA includes a network of electronic switches to change from one-port to two-port measurement seamlessly. In addition, with integrated Range-to-Fault (RTF) on each port, the user can first troubleshoot the system for internal PIM. Then, without reconnection, the user can progress with the external PIM process, making the entire process much more efficient.With integrated RTF on each port, the user can collect four times more range-to-fault data than the standard 1-port PIM Finder solution. Thus, the user can easily locate and swiftly eliminate the strongest PIM source.
-
product
Magnetic Effects Test
This test determines if an object can operate normally in strong externally generated magnetic environments. The magnetic effect test helps to assist in determining the proper location of the equipment in the installation.
-
product
Distributed I/O
Schweitzer Engineering Laboratories, Inc.
Expand the I/O of SEL relays and communications processors, reduce copper in substations by transferring I/O from remote locations over fiber, and provide electrical isolation to avoid ground paths and induced noise and interference.
-
product
PXI 8x9 RF Matrix 250MHz 75 SMB
40-725-751
The 40-725 is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz (50Ω version). The 40-725 is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connections, these disconnect the matrix from the external test fixture maximizing isolation and RF performance.
-
product
Smart Optical Time Domain Reflectometer OTDR
BD900 Series
Shanghai Baudcom Communication Device Co.,Ltd.
BD900 series of Optical Time Domain Reflectometer has excellent dead zone performance and wide dynamic range. There are four models to choose from and that can betterly meet the customer’s specific measurement requirements. Combined with the visual fault locator, it can easily find the breaks, bends, splices, faulty connectors, and other causes of signal loss.
-
product
Explosion-Proof Heaters
Explosion-Proof Heaters (ATEX certified) provide neutral convection solutions of heating for electrical equipments in hazardous industrial locations where potential for explosion exists due to the presence of flammable gases, vapors, powder-metals or dusts.
-
product
Law Enforcement/Public Safety
Vehicular and Handheld antennas are available for communication, surveillance, signal DF, network repeaters and RF Jamming applications. A single omni or high gain directional ARA antenna may cover all cellular and/or Tetra communication bands and are compatible with all network technologies (GSM, CDMA, etc.). These wideband antennas replace the need for several single band antennas and are ideal for vehicular installations as well as handheld radio mounted applications. Permanent installations, quick deploy magnetic mounts or convenient pistol grips for radio location are available.
-
product
Monics® SatID®
Kratos Defense & Security Solutions, Inc.
Kratos’ leading RF interference geolocation product, satID® provides an accurate, fast, all-in-one solution for locating and identifying sources of interference, including VSAT/TDMA terminals. With the capability to geolocate within 5 km of the interfering signal, satID is the most accurate geolocation product available today.
-
product
Cable Locator (LCD type)
5501 CB
Standard Electric Works Co., Ltd
● The 5501 CB transmitter is a great tool for locating and identifying cables and individual conductors● Locates both powered and unpowered cables ● Voltage measurement for cables: ACV 12V~450V DCV 12V~450V● Signal transmission • Transmission power level selection (includes 1, 2, 3) • Transmission signal code selection (includes F, E, H, d, L, C, O, A)● Flashlight & backlight function● Silent mode (disable button beep)● Level bar display on LCD screen (transmission power level indication)● Action wave display on LCD screen (when signal is transmitted)● Auto power-off function
-
product
Signal Acquisition and Filtering Technology
SNAPTrack®
Built on a proven design, and with Pathfinder SAF Technology™ at its core, the SnapTRACK® offers RYCOM’s most advanced signal acquisition and filtering technology. The SnapTRACK® cable & pipe locator offers utility locators FrequencyFlex™ allowing users to adapt the system to their specific needs. Multiple active frequencies allow the user to accurately locate with a minimum of interference while maintaining the ability continue locating past faults and around conduit bends. Passive frequencies identify "live" and charged lines by their naturally occurring electromagnetic fields. The SnapTRACK® offers multiple passive frequencies -- 50Hz, 60Hz, Radio Frequency, Cathodic Protection Rectifier & CATV -- allowing line locating without the use of a transmitter.
-
product
Partial Discharge Detection and Localization System for Power Transformers
AE-150™
The AE-150™ is designed to detect and localize Partial Discharge activity by correlating acoustic and electric sensors’ data. The AE-150™ has many acquisition modes, each used for detecting and locating Partial Discharge activity in a transformer. The AE-150™ unit is mounted on the transformer tank using its powerful magnets that also hold four acoustic sensors. Acquired data is sent to Mirador-Tx software where all advanced positioning functions are implemented. This cutting-edge software allows easy data interpretation, reporting and monitoring.
-
product
Mobil Cable Test and Fault Location System
SWG-12 (SWG-32)
• testing cable insulation with DC (rectified) voltage up to 32 kV;• conditioning faults by burning faulty cable insulation with current up to 100 mA;• pre-locating cable faults with the reflectometer RIF-9 based on the pulse reflection method (TDR), voltage wave oscillation method (DECAY), impulse current envelope (ICE) method and arc reflection method (ARC / ARC multi-shot);• pinpointing cable faults with the acoustic method with up to 2000 J surge wave generator and a suitable signal receiver.
-
product
High-Temperature Extensometers < 1000°C Capacitive
2632 Series
Is typically used in hot tensile applications with tube type furnaces and consist of a separate measuring unit and suspension arm assembly. The measuring unit uses an LVDT with a fixed travel that remains outside of the furnace, the arms are located mostly inside of the heating system and attach the specimen to the measuring unit.
-
product
Test Sockets
Yamaichi Electronics Co., Ltd.
A test socket is the ideal point to test your home’s internal phone wiring for faults. You can also use it to identify any potential faults with the phone line outside. Your test socket is located in your master socket. It is the point between the internal phone wiring in your house and the phone line outside. That means by plugging into your test socket you can bypass all the internal wiring and test your device directly on the phone line.
-
product
Fiber Splice Closures
Wuhan Sunma Technology Co., Ltd.
Fiber Optic Splice Closure is a fiber management product typically used with outdoor fiber optical cables. It provides space and protection for the fiber optic cable splicing and joint. Fiber splice closure is used for aerial, strand-mount FTTH "tap" locations where drop cables are spliced to distribution cables. SunmaFiber supplies two types of fiber splice closures which are the horizontal (inline) type and the vertical (dome) type. Both are made of excellent engineering plastics to be waterproof and dust proof. And with various ports types, they can fit different fiber optic core numbers. More details about splice closure.
-
product
In-Sight Vision Systems
9000 Series
The In-Sight 9000 is a rugged, ultra-high-resolution line of standalone vision systems. With its ability to acquire and process exceptionally detailed images, the In-Sight 9000 delivers high accuracy part location, measurement, and inspection over a large area—even when mounted at longer distances. Line scan and area scan image acquisition options are available for imaging continuously moving or stationary objects. Plus, a full suite of vision tools configurable through the In-Sight EasyBuilder interface solves a wide range of applications across industries.
