Sockets
receive conductors.
-
Product
COM-HPC Client Type Modules
-
The COM-HPC specification currently defines three client modules: Size A (95mm x 120mm), Size B (120mm x 120mm) and Size C (160mm x 120mm). The largest of the server modules, Size C (160mm x 120mm), offers up to four on-board SO-DIMM sockets. The power input is a single 12-volt supply that can deliver up to 251 watts of power, and there are 49x lanes PCIe Gen5 in total.
-
Product
Measuring Small Antennas
-
If you have a small PCB with a small antenna you can't use a thick cable and a large connector. Not only is this impractical (how to connect the connector?) but the metal bulk will also affect the antenna and grounding properties of your PCB. The measurement will be useless. MegiQ promotes the use of the small and popular UFL connector and its associated cables. The UFL socket fits on almost any PCB and it can be improvised on a board without a UFL footprint.
-
Product
3.5” Embedded SBC With Intel® Celeron® Processor J1900/J1800, DisplayPort, LVDS, VGA, 3 GbE LAN And Audio
CAPA84R
-
The CAPA84R is powered by the Intel® Celeron® processor J1900 quad-core or J1800 dual-core. The CPU is located at the rear side of the motherboard, which further aids the heat-extraction process and simplifies maintenance procedures. This fanless embedded board was designed for operational efficiency in rugged architecture with a wide operating temperature range of -20°C to +70°C. The CAPA84R supports one 204-pin DDR3L-1333 SO-DIMM socket with up to 8GB of system memory. There are also one SATA-300 port and one M.2 Key B supporting SATA for storage. The 3.5-inch embedded SBC with the Intel® integrated Gfx graphics is made to bring a true high definition visual experience with dual display configurations through the DisplayPort, 18/24-bit dual-channel LVDS and VGA.
-
Product
Socket Tester
ST120+
-
The Fluke ST120+ GFCI Socket Tester with Beeper checks that each wire in the outlet is properly connected to the building's electrical system. Via the bright LEDs and included chart, you can quickly and easily verify the wiring of an outlet. Able to identify several common wiring errors, including reversed phase and neutral wires and an open ground, the ST120+ will give you confidence on your next job.
-
Product
PXI/PXIe Power Relay Module, 16xSPDT
40-158-003-HI
Relay
The 40/42-158-003-HI is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin SGMC male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
Product
Fusion Bonded Cable Jumpers
Series 152FB
-
Fusion Bonded Cable Jumpers. Aries Series 152FB Fusion Bonded Cable Jumpers are flexible...plug them directly into PC boards or sockets. Stranded wire conductors are fusion bonded with an overcoat of tin for easy soldering or socketing. Each jumper is shipped with protective tabs on both ends for maintaining proper conductor spacing.
-
Product
PXI/PXIe Power Relay Module, 5 Amp, 50-Pin D-type Connector, With Interlock
40-158-103-HI
Relay
The 40/42-158-103-HI is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin D-type male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock.
-
Product
JTAG External Modules (JEM) DIMM/SODIMM Socket Cluster Test
-
The primary function of the JTAG External Modules (JEM) for the DIMM/SODIMM Socket Cluster Test is to provide test access to off-board signals that otherwise could not be accessed by a JTAG test system and to strengthen the memory-independent JTAG testing for the assembly correctness of the almost full spectrum of the modern socket types, particularly (according to JEDEC_Std.21-C):
-
Product
AC Line Harmonics Analyzer Including Flicker Analysis With UK, Schuko Or US Socket.
HA1600A
-
Compliance quality measurements to EN61000-3-2 and EN61000-3-3Measures peak or rms voltage or current, real or apparent power, power factor, phase etc.Tabular/histogram of 40 harmonicsVoltage/current waveforms displaysContinuous analysis with real-time graphical updateWide range of power connectors available320 x 240 pixel high-contrast displayUSB, RS232 and printer interfaces fittedPC control and documentation software supplied (HA-PC-Link+)
-
Product
Fanless Embedded System With LGA1151 Socket 7th/6th Gen Intel® Core™ & Celeron® Processor, Intel® H110, HDMI, DisplayPort, VGA, 6 USB, 4 COM, PCI Express Mini Card Slot And 10 To 30 VDC
eBOX640-500-FL
-
The eBOX640-500-FL is powered by the 7th generation Intel® Core™ i7/i5/i3 and Celeron® processor families. It features dual DDR4-2133 DIMM sockets with up to 32GB of system memory, and provides a wide choice of front-accessible I/O interfaces for easy cabling and maintenance. It supports an extended operating temperature ranging from -10°C to +55°C, a wide voltage range DC power input from 10 to 30 VDC with power protection, and up to 2G vibration endurance, enabling a reliable and stable operation in harsh environment. The superior Intel® Kaby Lake-based fanless embedded box PC can support three independent high resolution displays and 4K resolution, offering high quality imaging.
-
Product
Plug and Switch Testing
-
Applied to test electrical accessories heating conditions when connected to load current, whether the temperature rise of electrode is compliance with standard requirement or not. And it can effectively detect whether the plug bush is slants thin and whether plug and socket cooperated with all right.
-
Product
Peripheral Port Expander
-
The Peripheral Port Expander (PPE) is a connection box with 32 banana sockets (4mm) for easy connection to the various analog and digital inputs&outputs that are available in each Ivium potentiostat. The banana sockets are colour coded for easy recognition and include a5 V, max. 100 mA power point. A DB37-data cable connects the PPE to the potentiostat.
-
Product
Open Pluggable Specification-Plus (OPS+) Digital Signage Player With LGA1151 Socket 8th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® Q370 And TPM 2.0
OPS700-520
-
The OPS700-520 is an Open Pluggable Specification Plus (OPS+) digital signage player. The high-performance signer player is powered by the high-performance LGA1151 socket 8th generation Intel® Core™ i7/i5/i3 and Celeron® processors (codename: Coffee Lake S) with the Intel® Q370 chipset. This OPS+ digital signage module supports Trusted Platform Module (TPM) 2.0, Intel® Active Management Technology (Intel® AMT) 11.0 as well as Intel Unite® solution for content sharing and collaboration. It comes with two 260-pin DDR4-2400 SO-DIMM sockets that can provide system memory of up to 32GB. The Coffee Lake S-based OPS700-520 offering future-proofed flexibility and performance is among one of the most advanced and powerful digital signage players in the market.
-
Product
Interior Temperature Transmitter
T0118
-
Temperature transmitter is specially designed for use in exacting interiors in building energy management and HVAC systems. It designed for easy installation on ordinary KU68 wiring boxes for household switches and sockets. Large dual line LCD is possible to switch off. Computerized design ensures long term stability and fail indication. Transmitter is designed for use in non-aggressive environment.
-
Product
Polarized - PZN Connectors
-
Omnetics PZN (Polarized Nano) connectors offer some of the smallest board to cable mounted connectors in the industry. Using the most rugged Nano-pin to socket systems assure high performance in low profile light weight interconnections. These ultra-miniature connectors are available in a variety of board mount options as well as wired options.
-
Product
Fibre Channel Test & Simulation Interface for PCI Express
PCIe-FC4
-
Avionics Interface Technologies
Half-size four lane PCIe board - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speedsComprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
IEC60669 Pendulum Impact Tester
CX-BC2
-
Shenzhen Chuangxin Instruments Co., Ltd.
This Pendulum Impact Test Device Conforms to the standard GB2099.1, GB16915.1 and IEC60669, IEC60670 standard. To check the impact resistance performance of plug and socket electrical accessory's enclosure.
-
Product
7 Flat (Spade) Pin Trailer Circuit Tester
PT7893
-
Easily test trailer plug circuitry on most new light trucks, SUV's and RV's. Just plug the plug tester into the trailer plug socket and activate the lights, brakes, turn signal etc.
-
Product
6U CompactPCI Intel® 6th Gen. Core™ i3/i5/i7 Processor Blade with ECC support
MIC-3399
Processor Blade
- Supports 6th Generation Intel® Core™ i3/i5/i7 processors and Intel® CM236 PCH with embedded graphic (up to 3 independent displays)- Up to 32GB (DDR4-2133) memory (max 16GB on board, socket SO-DIMM x1, max 16GB)- Optimized dual-slot SBC with 2.5" SATA-III HDD/SSD, 2240 or 2280 M.2 socket, on-board Nandflash (optional)- Two SATA ports, two USB 3.0, six USB 2.0 ports, two DP ports, two COM ports, one PS/2, one Audio, one VGA and PCIe x8 interfaces to the Rear Transition Module (RTM)- Five Gigabit Ethernet ports including two PICMG 2.16 for front and rear connectivity- PICMG 2.16 R1.0, PICMG 2.1 R2.0, PICMG 2.0 R3.0, PICMG2.9 R1.0 compliant
-
Product
Signal And Image Processing Research
-
TPAC solutions are ideal for research in signal processing applied to ultrasound. You need to be able to access to any parameter, implement a particular algorithm, and access to any data during the acquisition or postprocessing phase. TPAC provides you all of these. It can be applied to studies in signal processing, image processing, beamforming, machine learning, etc… Thanks to TPAC’s open platforms, you will be able to freely set the ultrasonic sequences, record the raw data from your experiment, and test your own algorithms or even method. In order to adapt to a wide variety of habits, TPAC proposes multiple APIs (Application Programming Interface) compatible with Matlab, C++, Python, C#, Labview and working under Windows or Linux operating systems. Through a socket, it is even possible to use any OS of your choice.
-
Product
Readout passive probe
-
Rngs around the BNC input sockets that allow the attenuation factor of attached probes to be detected by the scope.
-
Product
Decades
-
PeakTech Prüf- und Messtechnik GmbH
For production testing, teaching aids, research and development. You can set all resistance values between 1Ω to 11.111 MΩ with high precision in 1Ω steps to get the desired value quickly and user-friendly. The angled plastic housing ensures a clear arrangement of the rotary switches, whereby the test leads are connected via 4mm safety sockets.
-
Product
Small outline PCB with 72 Pin Socket
1091-001
-
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
Non-Contact Voltage Testers
-
PeakTech Prüf- und Messtechnik GmbH
User-friendly tester for non-contact voltage testing from 50 V to 1000 V AC. Suitable for outlets, lamp sockets or against wire insulation testing. If AC voltage is present at the relevant measuring point, this is indicated visually by a flashing red LED and the integrated buzzer sounds. If the measuring point is voltage-free, the test probe lights up permanently green.
-
Product
Pico-ITX SBC With 7th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, HDMI/LVDS And LAN
PICO512
-
The PICO512 is designed to support the latest 7th generation Intel® Core™ processor or Celeron® processor 3965U. Coming with one 260-pin DDR4-2133 SO-DIMM socket supporting system memory up to 16 GB, the Pico-ITX motherboard also features a PCI Express Mini Card slot in support of mSATA and a pair of expansion connectors for an additional I/O board/signals. It supports a 4K visual experience with dual display outputs through HDMI and LVDS. Pico-ITX SBC can withstand a wide operating temperature range from -20°C to +70°C.
-
Product
JEDEC TO Collet Socket
Series 514
-
TO Collet Sockets. Aries TO sockets feature molded chamfer lead-ins for easy device insertion. High stand-off design for heat dissipation and easy cleaning. External polarization for positive location.
-
Product
InfiniiMax Differential/Single-ended Connectivity Kit
E2669B
-
Includes a differential browser, four solder-in differential probe heads, and two socketed differential probe heads.
-
Product
1U Rackmount Network Appliance Platform
NA580
-
The NA580 offers high reliability and performance through the LGA1151 socket Intel® Xeon® E3 and 7th/6th generation Intel® Core™ processors (codename: Skylake) with Intel® C236 chipset. The powerful network appliance supports up to 18 Gigabit LAN ports and allows system developers to configure their network solutions based on different performance requirements. Through the PCIe 3.0, the Axiomtek NA580 can integrate up to 18 Gigabit Ethernet ports. The standard configuration comes with 8 Gigabit Ethernet ports using Intel® i210 controller and supports 2 pairs of LAN bypass segments. Four DDR4 2133 MHz UDIMM sockets can provide storage of up to 32 GB and support both ECC and non-ECC memory types. To enhance reliability, this SMB network appliance platform supports data protection via 2 pairs of latch-type LAN bypass functions for fail-over option and features BIOS console redirection.
-
Product
Safety Critical Miniature Relays
CU-V Series
-
The CU-V is a so called safety relay which is used in places where a safe separation between coil and contact circuit is required. The relay is, with the corresponding screw socket V12, according to CEE 15/2e edition, approved by KEMA, for application in gas fired installations.
-
Product
Near Zero Footprint SMT Spring Pin Sockets
-
Ironwood Electronics socket is a device size or near device size footprint test socket incorporating industry standard high performance spring pins. Ironwood can design a socket to work with any type IC packages- BGA, LGA, QFN, DFN and even leaded devices where you need to fit a socket in place of your device to allow fast, easy testing and development.
