Verifiers
-
product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 32.7k Ohm - SPST
50-294-132
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI High Density Resistor Card 5-Channel, 16-Bit, 0 To 65k Ohm
50-295A-021-5/16
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
DGN Advanced Reporting Feature, GTE 10.00p
K8223B
The Basic Diagnostics levels is the main troubleshooting tool used by all users to check the hardware configuration, and verify and isolate hardware failures. Some Diagnostic tests require that a Pin Verification Fixture be installed on the system.
-
product
Functional Testing
To verify the functionalities of your software, to check for the quality of your product, and to see that the applicationis working against business requirements, opt for Functional Testing.
-
product
Radar・Sensor Simulation Framework
COSMOsim
Millimeter Wave Radar simulator and LIDAR (Laser Imaging Detection And Ranging) simulator for Automotive sensor simulations, and also can provide 3DCG MAP for specific radar which has millimeter accuracy. Now we can only provide AMMWR and ALR to the following COSMOsim Framework. This simulator enables automotive manufacturers to simulate a driving situation by sensor-based modelling, check the recognition and control of autonomous driving, and verify the sensor-mounting positions on vehicles efficiently, which eliminates the need for test driving with real vehicles.
-
product
Air Data Computer (ADC) Tester
MS 1122
The ADC tester is used in 2nd line maintenance is to check the functionality of ADC. This unit is a rugged customized hardware based on full functionality test of ADC. The Air Data Computer (ADC) Tester is a fully automated GO/NOGO tester with full functional testing in 2nd line maintenance. This tester is to test ADC at unit level and identify faulty Shop Replaceable Unit (SRU). This tester is also used to carry out PI checks on ADC before clear them for installation on aircraft. ADC Interface board designed to test full functionality of ADC. The Air Data Computer (ADC) test equipment shall be used for testing ADC of Tejas Aircraft. ADC test equipment shall verify the functionality against specifications during second line maintenance and pre-installation on the aircraft.
-
product
PCI High Density Resistor Card 6-Channel, 24-Bit, 0 To 16M Ohm
50-295A-121-6/24
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Automotive Ethernet Tx Test Software 10M to 5Gbps
AE6910T
The E6960A 1000Base-T1 automotive Ethernet compliance application software for Infiniium Series oscilloscopes provides you with a fast and easy way to verify and debug your automotive technology designs.
-
product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 131k Ohm
50-294-034
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PNA-L Microwave Network Analyzer
N5235B
Perform basic analysis of passive components and simple active devices Measure S-parameters with good accuracy up to50 GHz in cost-sensitive applications Get the world's best price-to-performance ratio for microwave manufacturing Configure an economical solution for signal-integrity measurements and materials characterization Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
PCI Resistor Card 2-Channel 1.5 Ohm To 8.19k Ohm With SPDT
50-293-124
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Video and Protocol Analyzer
The Video and Protocol Analyzer (VPA) verifies compliance of designs against the ARINC 818 standard. The VPA software and interface accurately and efficiently decode and display data and flag errors. Multi Stream is a new standard feature of the VPA, empowering it to tackle ARINC 818 interfaces with multiple embedded streams of high-speed video.
-
product
Safety
Test Equipment to verify Safety, Quality and Compliance characteristics of electro-technical products as required by national and international safety regulatory agencies. These equipment are used to check Electrical Wiring Accessories, Electrical Home Appliances, Industrial Luminaires, Motors and components or parts used in such products. Several of these safety test equipment are common to many standards and are required for routine 100% test purposes to ensure product safety.
-
product
SNMP Test Suite
SilverCreek
SilverCreek is the Authoritative SNMP Test Suite -- designed to test implementations of the Simple Network Management Protocol (SNMP agents) and standard and private MIBs (Management Information Bases). SilverCreek incorporates thousands of small, single function tests written in the Tcl scripting language to exercise one or a small number of parameters. The syntactic tests verify protocol compliance, error and exception handling, and boundary condition behavior. The functionality tests (semantic tests) verify performance, trap/alert/event/notification handling, counter accuracy, security, and many other implementation specific areas.
-
product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 1.02k Ohm
40-294-021
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
MPO Visual Cable Verifier Kit
KI-TK832
Kingfisher's unique and innovate MPO Visual Cable Verifier Kit is a quick, versatile and inexpensive way to visually check MPO cable installations and patch leads for polarity and continuity, and overall end face condition. Just connect the source, and view the far end with the microscope to observe the repeating color pattern at the far end.
-
product
Ammeters
*Measures AC current from 1 to 2000 Amps on system voltages up to 500kV line-to-ground*Stores the last 4 readings*Dual measurement modes, peak hold and real time*Takes spot-load checks with ease*Verifies phases are balanced*Versatile for overhead and underground applications*Compact, lightweight design
-
product
Calibrator for Battery Charger-Analyzers
VCM-100
The VCM 100 is an instrument designed to verify the performance and to calibrate Battery Charger-Analyzers used on Nickel-Cadmium, Lead-Acid and other types of batteries.
-
product
High Accuracy In-Situ Mass Flow Verifier
HA-MFV
The HA-MFV, High Accuracy Mass Flow Verifier is designed for use on process tools to verify mass flow control flow rates in-situ. Available with EtherCAT® or DeviceNet™ communications and measurement accuracy of 1.0% of reading, the HA-MFV can verify MFC flow with the actual process gas significantly better than older rate-of-rise devices or process chamber rate-of rise methods.
-
product
Mobile App Penetration Testing
To verify the functionalities of your software, to check for the quality of your product, and to see that the applicationis working against business requirements, opt for Functional Testing.
-
product
900 Hz to 120 GHz PNA MM-Wave System
N5291A
Single-sweep solution with compact frequency extenders Purchase as a single product solution Accurate leveled power can be applied to the device, providing the ability to sweep power Available various software application for detail analysis Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
Real-Time Spectrum Analysis up to 160 MHz, Optimum Detection
N9030A-RT2
Capture elusive signals as short as 3.57 with 100% POI and a complete set of advanced triggers View signal dynamics with displays: digital and swept density, spectrum, spectrogram, power vs. time, gap-free real-time analysis, and more Maximize your investment by adding RTSA to your PXA at a fraction of the cost of a dedicated solution Easily integrate the 89600 software and thoroughly analyze complex signals Extend RTSA measurements to millimeter-wave range with external mixers Industry-leading 3 year warranty Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
MCB Thermal Verification Test Bench
The test system is a special version of the thermal test test system in the sense that the test jig is primarily designed to hold and connect multi pole MCBs for thermal verification so that each pole can be verified to trip within the IEC time band after the MCB has been riveted. This test ensures the trip verification of MCB so as to trip all the 4 poles at once when overload is detected in one single pole. In short, this is a verification-only bench.
-
product
ESS Fixture
ESS - Environmental Stress Screening - is not a test. It is a product level screening process. ESS is part of manufacturing process, that verifies the operational parameters and guard bands of a product from an environmental - temperature, shock, vibration - point of view.
-
product
Structural Testing
Structural testing is used to verify the static strength, or fatigue strength, of a component by applying measured loads. Testing can be done to failure, to contractual requirements, or to validate finite element model predictions.
-
product
High Voltage Breakdown Test Sets
HT-Series
Dielectric Voltage Withstand Test or High Potential Test (HIPOT test) is a 100% production line test to verify the quality & electrical safety characteristics of products.
-
product
PXI Resistor Module 4-Channel 1R to 255R
40-293-013
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Trace-Level Dilution Calibrator
Model T700U
Teledyne Advanced Pollution Instrumentation
The Model T700U is a microprocessor based calibrator for precision, trace-level gas analyzers. Using highly accurate mass flow controllers combined with compressed sources of standard gases, calibration standards are provided for multipoint span and zero checks using up to 4 gas sources.In addition to the features of the Model T700, the Model T700U is designed for the demanding requirements of trace-level measurements. The ability to calibrate and verify linearity for NO2 at levels below 50 ppb is difficult with standard calibrators. To overcome this limitation, the Model T700U ozone generator operates in two modes; a high range with similar performance to the Model T700 ozone generator, and a low range, or "fractional" mode, for producing accurate ozone levels down to 3 ppb. To ensure the highest accuracy of NO2 output, the calibrator measures the ozone concentration prior to performing a GPT, and the range is selected automatically by the Model T700U based on ozone concentration and flow specified by the user.
-
product
Proving Unit& Calibrators
Shanghai Beha Electronics Co., Ltd.
Calibration box is used to verify and proof any High Voltage Insulation Testers. It can be utilized to calibrate all High Voltage Insulation Testers very accurately Analogs or Digitals.
-
product
Fiber Optic Visual Fault Finder
VFF5
Used to verify continuity, test and find breaks in fibre links, locate pinched fibre strands in termination cabinets, or anywhere fibre optic cables are terminated and subject to mechanical damage.
