Regulators
-
Product
RCD Testers
-
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2710 is a residual current tester, which is used to determine tripping currents and the tripping times of residual current circuit breakers, which are used in every new building according to current building regulations. Residual current circuit breakers are used for personal protection and switch off a circuit when a residual current is registered which flows off via the protective earth (PE). RCD testers let a fault current flow and thus determine at which fault current the RCD triggers. The tripping time is also measured. These two parameters, tripping current and tripping time, are the safety-relevant parameters of an RCD. The various selectable test currents and characteristics that can be set with this device make the PeakTech 2710 the ideal companion for every electrician.
-
Product
Power Supply 600W
UEP10M66 / CEP10M66 -
-
The UEP10M66 series is a linear regulated plug-in power supply for use in CERN type NIM and CAMAC crates with 600W power output for applications with extreme +/-12V loads. This high precision and lowest noise power supply is designed as a very compact unit with extremely low volume to power relation.
-
Product
Compact Bump Gas Solution
Eco Bump
-
Teledyne Gas & Flame Detection
Importantly, bump testing is the only way to validate that gas detectors will respond to gas and trigger user alarms.Simplified configuration (no software).Measuring only 7.2” (180mm) in height (including the push button regulator), the pocket-sized EcoBump can easily be stored and transported with minimal shipping costs.With 5.5L of bump gas capacity, EcoBump provides approx. 250 bump tests from a single cylinder making it our most cost effective bump solution.
-
Product
High Frequency Clock Divider Board
-
Alliance Support Partners, Inc.
Clock Divider is designed to divide high frequency signals, up to 2.5GHz, from 4 to 256 times. It will accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms. The clock division is controlled by 4 shunt jumpers. The circuit can be disabled and the divide by counter reset with 2 control signals. The on board regulator will accept voltages from 4.85 to 15.0V. The output is capable of driving 700mV Peak to Peak into 50 Ohms.
-
Product
SparkFun FTDI Basic Breakout
Beefy 3
-
This is SparkFun Beefy 3 FTDI Basic Breakout for the FTDI FT231X USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. Built upon the same foundation as our 3.3V SparkFun FTDI Basic Breakout, the Beefy 3 is equipped with an AP2112K voltage regulator making this FTDI basic breakout board capable of handling a current load of up to 600 mA! With the addition of a more "Beefy" voltage regulator your will now be able to power a 3.3V project directly from the FTDI. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards.
-
Product
Rock Mechanics Testing Equipment
-
Rock mechanics is the part of geotechnical engineering that studies the behaviour of rocks under variable physical and environmental conditions. Testing is undertaken to enable the prevention of geotechnical failure such as shearing, by measuring the behaviour of rocks for compliance with regulations, design specifications and quality control standards.
-
Product
DC Electronic Load
EE15120A
-
The EE15120A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices. The electronic load can act as a Current Regulator for charging
-
Product
Linear Regulated Power Supplies (to 150 watts)
Gold Box "Infinity"
-
*Highly Configurable, with a seemingly Infinite number of Options*Any slot voltage from 1.5v to 150v is available*Remote Sensing*Open Sense protection*Isolated output*Short circuit and overload protection with enhanced surge capabilities*No minimum load required*Internal EMI Filtering*Pluggable connectors*Can be mounted on two surfaces in any orientation
-
Product
Linear Regulators
-
Renesas' single and dual low dropout regulators (LDO) offer ultra-high PSRR up to 3MHz, low input voltage range, tiny packages, and ultra-low noise and quiescent current.
-
Product
35W Low Profile Triple Output Power Supplies
CUT35
-
The triple output CUT35 and CUT75 power supplies have two independent, isolated, converters, one for the main 5V output, and one for the auxiliary outputs. This topology provides several benefits - no minimum loading, enhanced load & line regulation and the ability to connect the auxiliary outputs in series to generate either a 24V or 30V output. This flexibility makes it suitable for use in a wide range of process control, broadcast, test & measurement, medical and industrial equipment applications.
-
Product
Bench DC Power Supply - Mixed-mode Regulation With Analogue Controls. Single, Dual Or Triple Outputs, 175 To 420 Watts
EX-R Series
-
Single outputs, 35V/5A, 18V/10A, 42V/10A, 20V/20ADual or triple outputs, 35V/4AIndependent digital voltage and current meters for each output with 4 digit resolutionSwitchable local or remote sensingConstant voltage or constant current operationVariable 1.5 - 5.0V auxiliary output at 5A (EX354RT)Compact design uses less bench spaceSilent fan-free cooling (not EX202R/EX4210R)DC output switches, automatic mode indicationRS232 or USB controlled models available (35V/5A single)Multi-mode dual model 2x(75V/2A) or 75V/4A or 150V/2A
-
Product
BiGEN Power Supplies
-
BiRa Systems and TDK-Lambda collaborated to develop and support an accelerator laboratory family of programmable DC power supplies. The BiGEN family of power supplies provides many features including EPICS compatibility, interlock monitoring, precision current regulation, and air filter kits to fit the harsh accelerator environment. The BiGEN family of power supplies was based on the TDK-Lambda Genesys™ power supplies which can be configured in parallel and series for additional output power.
-
Product
GPON ONT
ONT-2GE-DW
-
Hangzhou Softel Optic Co., Ltd.
ONT-2GE-V-DW (Optional)+WiFi GPON/EPON HGU terminal devices are designed for fulfilling FTTH and triple play service demand of fixed network operators. These boxes are based on the mature Chipset (Realtek) technology, which have high ratio of performance to price, and the technology of IEEE802.11b/g/n/ac WiFi, Layer 2/3, and high quality VoIP as well. Support full management of HGU devices through SOFTEL OLT. They are highly reliable and easy to maintain, with guaranteed QoS for different service. And they are fully compliant with technical regulations such as IEEE802.3ah、ITU-T G.984.x and technical requirement of GPON Equipment (V2.0 and above version) from China Telecom.
-
Product
CO2 Concentration Transmitter
H5424
-
The regulators are designed for online measurement of temperature (C or F), relative humidity and carbon dioxide concentration of air without aggressive ingredients. Measured temperature and relative humidity are recomputed to following humidity expression: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Dual Output Digital Lab Series Regulated DC Power Supply – Upto 1280W
-
- 300W to 1280W different combination- High current density.- 19″ rack adaptable -3U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation- Optional, at extra cost- Over voltage protection- 19″ rack mounting- Analogue programming and monitoring for V&I
-
Product
Quasi Square Wave Constant Voltage Transformers
-
Osborne Quasi Square Wave Constant Voltage Transformers are used to regulate output voltages for applications that have varying input voltages. When used with a rectifier conversion circuit, these units provide an elegant design approach to voltage regulation. Osborne achieves this innovative approach by partnering the constant voltage transformer with an auxiliary resonant capacitor winding. The result is a unique (though time honored) technology that offers reliability, performance, and cost advantages over other styles of voltage regulation.
-
Product
Regulated Power Supply
PA-B Series
-
* A wide range of series and lineup, the experimental course, available use in a system and production and a wide range of scenes.10V,18V,36V,80V,120V,160V,250V,350V,600V* External remote control equipped with a terminal on the back, enables ON / OFF and output ON fixed output by the contact signal from the external.*In addition, external voltage, an external resistor, can be the output voltage and output current to the remote control.*In addition equipped with the adjustment for the volume at the time of external control on the front panel, you can adjust the offset and full-scale.
-
Product
Titration
Titrando
-
Titrando titrators have been developed to meet exacting titration demands. These titrators come with a wide range of security and traceability options, making them particularly suitable for use in regulated industries. Titrandos are capable of performing all common titration types and offer a host of automation and control options.
-
Product
Power Discrete Tester
Mostrak-2
-
M2 test system has multiple test generators which cover static and dynamic test procedures. It is our first truly modular tester which allows for the system to be upgraded and expanded when needed. M2 are designed to get the tester as close as possible to the handler interface and operator at the highest possible speeds. M2 is capable of HV (3 kV) and LV (600A) testing and has dynamic switching capabilities up to 1200V. MOSTRAK systems can test the following device types: MOSFET, IGBT, Bipolar transistor, Diode - rectifiers, Thyristor (SCR) - Triac, Linear voltage regulator (VReg), Transient voltage suppressor (TVS).
-
Product
Field Current Regulator
-
We are counted amongst the leading names in the industry, offering wide range of Field Current Regulator. Our entire product line ensures easy operations and is performance based. Field Current Regulator are quality tested and are delivered in standard configurations. Our entire product range has high strength and is delivered at most affordable rates.
-
Product
Bench/System Precision Linear Regulated DC Power Supply With Digital Control, Single Or Triple Outputs, 105 To 242 Watts, With/without Remote Interfaces
QL Series II
-
Advanced dc power supplies, single or triple outputUp to 112 watts per outputVery high precision, very low noise, excellent dynamicsAdvanced user interface with numeric and rotary controlMultiple voltage/current ranges for increased flexibilityMultiple non-volatile memories for power supply set-upsSwitchable remote sense provides perfect load regulationComprehensive protection including OVP and OCP tripsCompact bench footprint; modular width for rack mountingAuxiliary output fully variable 1.00V to 6.00V at 3A with selectable voltage and current metering (T models)Bus programmable via USB, RS232, GPIB or LAN (P models)LAN interface is LXI compliantDuplicate power and sense terminals at rear (P models)
-
Product
CO2 Concentration Transmitter
H5324
-
The regulators are designed for online measurement of temperature (C or F), relative humidity and carbon dioxide concentration of air without aggressive ingredients. Measured temperature and relative humidity are recomputed to following humidity expression: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Battery Resistance Tester
BT-3915
-
Kongter Test & Measurement Co., Limited
Regular test of battery internal resistance or battery conductance is essential for stationary batteries. It is also recommended by latest regulation of IEEE 450, IEEE 1188 and IEEE 1106. The excellent performance of BT-3915 for testing battery internal resistance and voltage will help you pick out the weak batteries and ensure their performance in short time measurement.
-
Product
AC Power Supply and Frequency Converter
P Series
-
The P Series AC Power Supply and Frequency Converter for your test bench or test rack delivers clean regulated AC power in a (2U) 3.5" high and (3U) 5.25” high bench top unit that easily converts to rack mount, for far less cost than competitive models.
-
Product
PCI Carrier Board
MS 1714
-
*64 bit PCI edge connector*64 bit PMC connectors*Operated frequency up to 66MHz*Regulated 3.3v supply to module
-
Product
Programmable Linear Dc Power Supply
DP700 Series
-
DP700 is a basic power supply product designed for users with lower cost and smaller size and high reliability. It has low ripple noise, fast transient response, excellent power supply and load regulation rate, powerful timing output function and complete protection function.
-
Product
Ethernet-GPIB-USB to Modbus RTU Interface
Model 9009
-
* All interfaces provide full control of the Modbus RTU slave devices.* Ethernet port supports VXI-11, raw socket and Modbus TCP/IP to Modbus RTU conversion. * GPIB port works with any IEEE-488.2 compatible GPIB controller.* USB port uses Microsoft supplied driver to prevent operating system change problems.* The 9009 uses a simple command set that is accessible from any port.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls. Works with Agilent, NI and Kikisui VISA libraries* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Ethernet interface protocol is fully VXI-11 compliant and does not require special PC drivers.* Internal webserver with sample Modbus device control pages for Watlow F4, F4T and EZ-Zone Controllers.* OEM oriented board designed for integration inside the user's system with only one cable. On board regulator works with 5 to 15 Vdc power.* Support programs Include ICS's VXI-11 and VISA keyboard control programs and a NTML page utility for uploading your customer webpages.
-
Product
Digital Lab 30W – 300W Regulated DC Power Supplies
-
- 19” Rack Adaptable – 3U High Digital Output Metering 3 Digit DPM- Constant Voltage/Constant Current Operation- High Stability and Close Regulation ±0.01%- Proven Reliability and Endurance- 3U High- Remote Sensing Facility for 5A & Above Rating Models
-
Product
Powered NIM Crate
NIM CERN-CE 600W
-
The CERN spec./CE NIM crate series represents modular designed NIM crates with linear regulated power supplies in excellent and proven W-IE-NE-R quality, conforming to EUR4100 and CERN specifications. These NIM crates are outfitted with 600W linear regulated, low noise plug-in power supplies for demanding applications.
-
Product
DC Electronic Load
Model - KM-mPD-501
-
Kusam Electrical Industries Limited
KM-mPD-501 DC electronic load mainly focuses on the testing of power circuit on PCB. KM-mPD-501 offers a solution for function test of Switch step up, Stepdown, Regulators and Driver IC . Engineer puts components, such as CPU, DSP, FPGA; etc on a PCB after the power circuit has been tested. It’s not complete to use a meter to measure the voltage. KM-mPD-501 offers engineer OVP, OCP and OPP functions that help engineer know the value of overload current . On the other hand, engineer can use a programmable DC power supply (mPP series) to offer external power and connect PCB’s output to KM-mPD-501. Then engineer can easily get output watt, figure out the efficiency of power circuit and check if inductances, capacitances and resistances perfectly work with the power circuit. KM-mPD-501 not only offers loading emulation of current but also provides OVP and OPP. User can use these functions to test solar power battery, rechargeable battery and motor driver. In school laboratory, KM-mPD-501 helps students do experiment on power circuit, linear circuit and driver circuit.
