Line
-
-
Product
PXI-6723, 13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module
778998-01
Analog Output Module
13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module—The PXI‑6723 delivers low-cost, high-density analog outputs to meet a wide range of applications, such as stimulus-response, signal simulation, waveform generation, and actuator stimulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6723 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-02
Interface Module
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
Robotic Vehicle Gap / Flush Measurement System
Automation
-
LaserGauge® Automation is a robotic system for measuring vehicle gap/flush on a moving assembly line. It is cost-effective, fast, flexible, and delivers LaserGauge® accurate measurements. Utilizing the Cross-Vector scanning and Blue Laser Technology, the system provides more assembled-panel surface information than any other robotic laser profiler.
-
Product
Automotive Radar Test ∙ Evaluation
XRE
-
KEYCOM develops and manufactures various radar systems to measure and evaluate such functionalities of mass-produced millimeter and microwave radars including in-vehicle radars as transmission power, frequency, antenna beam alignment, distance accuracy, bearing accuracy and receiving accuracy. KEYCOM’s product line includes the Radar Test System (RTS) that measures radar distance accuracy and transmission power, and the Rader Alignment System (RAS) that assists you to adjust the mounting position of the in-vehicle radar.
-
Product
HPA General Purpose Probes
General Purpose Probe
General Purpose Spring Probe contact solutions are designed for high volume testing and feature the industry-proven Pylon line. General-purpose probes are offered in both replaceable and non-replaceable options.
-
Product
PXI BRIC8 FIBO Matrix Dual 80x4 3pin brkout
40-592A-104
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
- RS-485 DIN Rail Mounted Surge Suppressor
Model 8021NX
-
FEATURES: Fast Response; Automatic Recovery; Up To 20 MBPS Data Rate; DIN Rail Mounted; Triple Stage Protection; Two Wire. The Model 8021NX is a DIN Rail mounted surge suppressor for 2-wire RS-485 circuits used to protect factory data networks, or, any RS-485 network that wants to avail itself of the DIN Rail packaging concept. The Model 8021NX provides common-mode (line to ground) surge protection and differential mode (line to line) protection for balanced networks. All the inputs, outputs and ground connections are via screw terminals located on the top surface of the device.
-
Product
Portable Three Phase Energy Meter Test Set
SY3632
-
Hong Kong Songyang Industrial Ltd.
The SY3630 Energy Meter Testing Instrument is used to calibrate three phase, single phase, active or reactive energy meter under work, and also it can be used as voltage, current and power meter to measure AC parameter of three phase power line. Same as ZERA and MTE. Of course our price is very reasonable.
-
Product
Extractive Gas Analyzers
Advance Optima and EasyLine Series
-
ABB offers three series of extractive gas analyzers catering to a diverse range of industries and applications. Sensing technologies perfected over more than 90 years are the foundation for a modular architecture delivering market leading performance and reliability – Uras (NDIR), Limas (NDUV), Magnos (Paramagnetic), Caldos (TCD), Fidas (FID), ZO23 (Zirconia). ABB also offers tunable diode laser (TDL) analyzers that measure in situ, directly at the stack or process line. The analyzers are world renowned for ruggedness, easy installation and operation in safe and hazardous areas, simplified calibration and outstanding possibilities for integration in digital networks.
-
Product
Dual-in-Line (DIL / DIP) Reed Relays From Pickering Electronics
Reed Relay
Pickering Electronics Series 97 & 98 DIL / DIP Reed Relays feature the highest quality instrumentation grade reed switches making them suitable for the most demanding applications. They are available in two ranges featuring internal mu-metal magnetic screens.
-
Product
NIRLine Spectrometers
-
Instruments in our AvaSpec NIRLine are high-performance, near-infrared spectrometers that are optimized for the demands of measuring long wavelengths. This line provides leading-edge performance for dispersive NIR instruments with a toroidal focusing mirror and dynamic dark correction for enhanced stability.
-
Product
Battery Monitoring System
BMS-3923
-
Kongter Test & Measurement Co., Limited
This battery monitoring system is an innovative solution to measure battery condition with communication way of Power Line Carrier (PLC). With multi-frequency measurement, users can monitor and analyze battery in all aspects: internal resistance, voltage, current, capacitance, temperature and so on.Based on our years experience for battery management system, we build very mature mathematical model that precisely predicts battery capacity. This will in another hand reduce the time that we spend on capacity measurement using a battery load bank.
-
Product
Outdoor AGC Optical Node
SR814
-
Hangzhou Softel Optic Co., Ltd.
Based on plenty of experience about CATV HFC network optical fiber transmission equipment, we developed SR802, SR802B, SR804, SR804B series field optical receiver which is two-way optical receiver; They are mainly used in long-distance optical fiber transmission of TV image signal, digital TV signal, telephone voice signal and data (or compressed data) signal. We are innovating the product technology, rebuilding the line structure and Improving the process quality since we developed the first CATV optical receiver successfully in 1995; The current WR series optical receiver are not only of the lead position in domestic level regarding line technique, but also the same as imported product regarding technological quality; We have developed a variety of different models for users to choose models.
-
Product
Power modules
-
G.R.A.S. Sound & Vibration A/S
It provides polarization voltage for the transducer, ensuring that the microphone gets the charging voltage it needs.It provides supply voltage for the microphone preamplifier. The preamplifier acts as a unity gain impedance converter. It provides a certain amount of line drive capability by providing a low output impedance and output current, making it possible to transmit the signal from the transducer to the Power Module without significant degradation.A power module can provide amplification or attenuation to the signal, thus making it possible to fine tune the measurement chain to the signals being measured and the hardware being used.Selectable filters make it possible to exclude unwanted noise from the measurement, e.g. wind induced noise from outdoor measurements.Overload detection makes it possible to validate the measurements and is a useful tool in monitoring setups.When a Power Module with gain is used, you can use longer cables because of the power module's ability to deliver current.A Power module introduces electrical isolation
-
Product
Expandable Fanless Embedded Computers
-
ADLINK's MXC product line provides fanless embedded computers for high-performance embedded solutions. Leading the field, high-performance computing power combines with PCI/PCIe high-speed expansion slots in a compact enclosure fully enabling integration of a variety of applications.
-
Product
Microwave Wideband Externally Modulated Transmitters (without RF Amp)
MT80 (30KHz~40GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MT80 series microwave optical transmitter, adopts external modulation technique, are able to transmit 40GHz microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 40Gb/s high speed communication system. MT80 adopts low noise, narrow linewidth CW DFB laser as light source; LiNbO3 external modulator as signal modulation, no laser chirp, low dispersion distortion, high extinction ratio, Full-transparency operation mode. It can be applied in long distance and extra-long distance transmission after EDFA.
-
Product
Keysight 64-bit Digital I/O with Memory and Counter for 34980A
34950A
Digital I/O Module
The Keysight 34950A module for the 34980A Multifunction Switch/Measure Unit has 64 bi-directional lines configured as eight 8-bit channels. Each 8-bit channel has programmable polarity and thresholds up to 5V. The memory is useful for simulating and capturing digital patterns up to 10 MHz. It provides configurable handshaking protocols for a wide variety of applications.
-
Product
High-Performance Gaming Platform with Backplane Architecture
ADi-SC2X
Gaming Platform
- High performance, high-end gaming platform with backplane architecture for easy maintenance- Superior, highly scalable CPU/GPU performance- Advanced security feature set and software solutions- Highly flexible system configurations that are fully in line with real project requirements- Lower costs: due to implementation of socket-type Intel® CPUs- Flexible maintenance and upgrade: slot-in machine construction, socket-type CPU support- Flexible maintenance and upgrade: slot-in machine construction, socket-type CPU support- Full-scale customization: GDDR5, V-BIOS, video ports, I/O ports, etc.- High integration: FPGA & logging controller onboard
-
Product
Adapter & DC Block
-
RF Lambda’s DC blocks are used to prevent DC signals from passing through a coaxial RF interface. They are low IL and wideband. RF Lambda’s line of adapters are used to connect RF signals using different connector options.
-
Product
Automatic Transformer Tester
SS3250 / SS3252 / SS3302
-
Automatic transformer test instrument is a precision test system, designed for transformer production line or incoming/outgoing inspection in quality control process, with high stability and high reliability. With the enhanced capability in turn ratio measurement, they can solve the measuring problems of low coupling coefficient, transformer's turn ratio and turn number with more precise measurement.
-
-
Product
Bi-Directional Level Translator
IFB-10001
-
Easily connect Arduino or other 5V microcontrollers to ~3.3V sensors. Based on the TI TXB0108 auto-sensing, bi-directional level translator, this module provides access to all 8 channels of the TXB0108 and has a built-in 300mA LDO with 200mV max dropout voltage at full load. Regulated 3.3V output allows this single board to both interface withandpower 3.3V sensors. An important feature of this module is the ability to operate SPI and other digital lines (not including I2C) at high-speed, whereas the 'NXP level shifter' maxes out at 400kHz and resistor dividers fail much earlier. The TXB0108, integrated with the LP3981 LDO, provide a fast, reliable solution to mismatched interface voltages that exceeds the performance of other solutions.
-
Product
Battery Cell Formation System
17000 series
System
Chroma 17000 series is specifically designed for the formation of Lithium Ion and Lithium Polymer secondary batteries. The 17000 series is a complete turn-key system, including carrier trays, robust battery probe contacts, high quality charge/discharge modules and intuitive software all under computer control. Patented Battery Voltage Tracking (BVT) DC-DC conversion power modules minimize power consumption in battery charging, and Energy Recycle Modules (ERM) recycle the discharged energy directly back to the DC power system for increased power efficiency. These power saving designs provide a planet friendly solution along with cost savings by reducing energy consumption. The intuitive software provides a flexible selection in the charge/ discharge channel, current rating, and modules under test. These features allow the Series 17000 to be used for final cell development, pilot line production, high volume production and ongoing reliability monitoring/quality control.
-
Product
Clamp Meters
-
The clamp meter is ideal for measuring AC or DC voltage. The instrument is irreplaceable for inspection work and maintenance in various industrial applications, in research and development, in residential applications and in many small businesses or households. The PCE line of clamp meter is made according to the highest industry standards and very important: PCE offers instruments that are usable in all workspaces (equipped with very small or even very large jaws), the results are reliable and the clamps are easy to use. Every clamp meter is manufacturer calibrated and can be certified to ISO or NIST - hold a PCE clamp meter in your hands and you can feel the quality immediately.PCE offers a variety of models: Voltage detector, voltage leak detector, voltage power detector, metric detector and current detector. In addition many clamp meters are able to measure other parameters, such as capacity, resistance and power - power through clamps directly or by handheld digital instruments with external clamps (with a range of one or three stages). Very often the clamp meter is a real multimeter - so it becomes a general electrical measurement tool.
-
Product
ACCUplace BullsEye /Recognition Grid
AP-B Series
-
A unique concept in imaging calibration technology, The ACCUplace Bulls Eye / Recognition Grid allows the end user to calibrate magnification at multiple power levels, as well as test the system’s ability to recognize and locate distinctive shapes within shapes by focusing on the concentric circles.Each Bulls Eye / Recognition Grid target has individual patterns consisting of 5 concentric circles with 0.50mm line width and 0.50mm spacing between circles (10mm Pitch) with a 0.100mm center dot. In addition, each row and column is labeled with X & Y coordinates. The AP-B series is offered on four standard substrates; Chrome on Glass (CG) Opal (OP) Photopaper (RM) and Film (TM).
-
Product
RF Cable Assemblies
-
Transmission lines for radio frequency (RF) signals traveling from one point in a system to another (e.g., PC board to PC board, PC board to antenna, equipment to antenna, equipment to equipment, etc.).
-
Product
DC Precision Measuring
-
Precision instruments for calibrating and monitoring. Our line of Precision Bridges, Decade Boxes, Galvanometers, Potentiometers, and standard high precision resistors, allow customers the accuracy and quality demanded in a precision device.
-
Product
Powered Crates
-
CAEN has decades of expertise in design and production of VME and NIM powered crates. The full line of crates is intended to guarantee reliability and mechanical solidity. CAN offers a selection of NIM, VME and Mixed Powered Crates with different configuration of power supplies and backplanes. Some crates can be ventilated with pluggable fan units, which also allow to have additional interfaces for remote monitoring and setting via CAN bus, Ethernet, USB and RS232.
-
Product
Line Tracer
MI-2093
-
Field proven instrument for under-wall low voltage installation tracing, fuse finding, short-circuit spot determination and metal installation tracing. Accurate fuse locating
