PCMCIA Adapters
Adapters that fit in the PCMCIA slot in notebook computers. Different adapters have different functions but they all add connectivity possibilities. (beststuff.co.uk)
-
Product
I2C Adapter
RS485
-
*RS485 address adjustable via DIP switch*I2C frequency adjustable up to 400kHz*I2C level shifter, I2C level from 2V to 15V*Interrupt input for external events*Simple software interface (ASCII commands)
-
Product
SIMRC - SMB RF Adapter PCB
1092-001
-
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
Adapter, APC-7 to SMA (f)
11534A
Contact Adapter (Receiver)
The Keysight 11534A is a general purpose grade, APC-7 to SMA female adapter.
-
Product
Power Line EMI Adapters
-
How much EMI noise is on your power lines indeed? How to assess the levels of noise and its properties when it is obviously a bad idea to connect your oscilloscope or a spectrum analyzer directly to your power lines?Our EMI interface adapters provide a barrier for high mains voltages but a straight passage for high-frequency signals so that you can connect your sensitive instrument to power lines for analysis and quantification. We offer plug-in and hand-held adapters which can measure both differential ("normal") and common-mode noise.
-
Product
PCIe Adapter for XMC
PCIe8LXMCX1
-
Simple and easy to use. Install PCIe8LXMCX1 into your PCIe system to adapt an XMC card. The XMC can have bezel and or rear IO. Pn4 and/or Pn6 are supported with PCIe8LXMCX1. 8 lanes are routed from the PCIe gold fingers to the XMC position.
-
Product
Multi Interface USB Adapter
SUB-20
-
SUB-20 is a versatile and efficient bridge device providing simple interconnect between PC (USB host) and different HW devices and systems via popular interfaces such as I2C, SPI, MDIO, RS232, RS485, SMBus, ModBus, IR and others. It is also a full "any to any" converter between all supported interfaces and I/O features. SUB-20 is a powerful I/O controller with 32 GPIO, 8 Analog Inputs, PWM Outputs, Edge DEtectors, LCD, Leds and push buttons.SUB-20 system includes SW package containing driver, API Library, GUI and Command Line based applications, C,C++,C#,VB.net, MATLAB, LabView sample code and documentation. SUB-20 can be used with PC 64/32 bit running Windows 2000/XP/Vista/Win7/Win8, MacOS, Unix/Linux and DOS.Working with SUB-20 does not require deep knowledge of low layers of the specific interface. All you need to do is to call right API function at the right place. And this is really very easy as API functions are well documented and "exampled". API set is relatively small but comprehensive.SUB-20 is equipped with status Leds, optional LCD and buttons. All this guarantee fast and comfortable development, field debugging and maintenance of applications including option of standalone operation.
-
-
Product
NI-6585B , 200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO
784060-01
Digital I/O Adapter
200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO—The NI-6585B is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a digital instrument for interfacing with 32 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6585 can operate at up to 200 MHz clock rates and includes support for common LVDS voltages.
-
Product
Off-Card Adapter,
3910-FOFE
-
As the physical size of Fibre Optic Front End (FOFE) transceivers prohibits their use on PCI, CompactPCI, PMC and ISA (PC/AT) cards, Western Avionics provides an off-card Adapter, that contains all components to support the 3910 Optical implementation of STANAG 3910. The 3910-FOFE Adapter provides a complete dual redundant optical interface, together with dual redundant 3838 connections, and Trigger-in and Trigger-out in a minimal sized package, to allow convenient cabling connections to the 3910 / 3838 system or unit-under-test.
-
Product
Chip Test Adapter
RAMCHECK Sync
-
The RAMCHECK Sync Chip Adapter tests popular TSOP SDRAM memory chips in sizes of 16Mx16, 4Mx16, 32Mx8, 8Mx8, 64Mx4, 16Mx4 and more. Picture above shows the adapter with all optional sockets for 54, 50 and 44-pin.
-
Product
cPCI and PMC Compatible Adapter Carrier
cPCIBPMC3U64ET
-
By customer request Dynamic Engineering has developed two extended temperature versions of the popular cPCIBPMC design. The design effort included switching to a new bridge to meet the temperature and timing requirements. The new bridge brings new features including the ability to operate the PMC side at a higher clock rate than the cPCI side. The new bridge also has built in features for local address spaces, using the PMC clock in monarch mode for the secondary side, and operating in transparent or non-transparent modes
-
Product
X.25 Adapters & XOT
FarSync X25 T2Ue
-
The FarSync X25 T2Ue PCIe card provides 2 high performance X.25 communications lines for Linux and Windows systems. A PCI version is also available.
-
Product
XMC-PCIeStor, High Speed PCIe Quad M.2 SSD Adapter
9303
-
The 9303 is an air or conduction cooled, extended temperature XMC card with 4 M.2 SSD sites for multi-terabyte storage. Onboard Gen2 PCI Express (PCIe) switch connects one 4-lane upstream PCIe port to four 1-lane downstream ports.
-
Product
Type 2, PCMCIA Dual Redundant MIL-STD-1553 serial bus Simulator Analyzer Tester
PC401
-
MIL-STD-1553 A, B, & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester type 2 PCMCIA BUS Interface Card - The PC401 can be used for Validation Testing, ProductionTesting, full bus simulation and monitoring, as a generalpurpose 1553 interface or a stand alone bus Analyzer. Forprecise message scheduling and measurements, the Majorand minor frame times are independent of messagesequences or retransmissions on errors and the start of allcommand messages are independent of message length,response time or length of response. Message timing iscalibrated and RT responses have low jitter.
-
-
Product
Adapters & Converters
-
Using our prebuilt, off-the-shelf standard adapters, custom converters, or custom adapters, incorporate performance and process data from across your enterprise, without having to disrupt your manufacturing line or change the outputs or your manufacturing process.
-
Product
Self Test Application Adapter and Software
OTP2-Modul-Nr210
-
In order for the system to carry out a self-test, it requires a suitable adapter and software that is tailored to the test system. A self-test is often very helpful and recommended if a system has not been used for a long time or also to see whether the test system is working properly with the specified parameters.
-
Product
Adapter Kit, Type-N and Type-F, 75 ohm, DC to 2 GHz
86211A
Accessory Kit
The Keysight 86211A adapter kit contains three Type-N to Type-F 75 ohm instrument-grade adapters, necessary when measuring Type-F devices on network analyzer with Type-N ports.
-
Product
Interface Adapter. USB Solution
U2C-11
-
Dimax USB to I2C Bridge device - U2C-11 converts USB transactions to I2C Master transactions. U2C-11 turns your PC running Windows or Linux OS into comprehensive I2C Bus master.
-
Product
EBIRST 104-pin D-type To 96-pin SCSI Adapter Cable
93-022-226
-
The 93-002-226 104-pin to 96-pin eBIRST adapter cable is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
PMC to PCI Express Adapter w/ TSI384
6083
-
The Technobox, Inc 6083 4-lane and 8638 1-lane carrier card allows use of a PMC in a PCI Express edge card slot. The product features an IDT TSI384 bridge IC used in transparent mode with a PCI express primary side and a PCI/PCI-X secondary side.
-
Product
Adapters
-
They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
Product
X.25 Adapters & XOT
-
FarSite supply the world’s largest range of X.25 adapters for PCs, Servers and Laptops a USB adapter, 2 and 4-port PCI Express adapters. 2 and 4-port Universal PCI adapters. 2 port PMC adapters and XOT software for Linux.
-
Product
USB CAN Interface Adapter
COMMDongle
-
Designed for use with VISUALCONNX and other third-party software, COMMDongle products initially support one or more CAN communications buses.
-
Product
Pulse Adapter
CV30 P300
-
Frothingham Electronics Corporation
The CV30 P300 test station is the highest current 30KW pulser in a series of exponential pulse generators that can be connected to our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of high power exponential pulses. For exponential pulses up to the 10/1000, the station can produce 30KW, 1000A, or 300V whichever is the most limiting. The station can also include all of the usual FEC200 tests in the same test program.
-
Product
Pulse Adapter
CV5P350
-
Frothingham Electronics Corporation
The CV5 P350 station is the first mid power pulser in a series of exponential pulse generators that can be connected to an FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of high power exponential pulses. For exponential pulses up to the 10/1000, the CV5 P350 can produce up to 5KW, 500A, or 350V whichever is most limiting. It can also test all of the usual FEC200 tests in the same test program.
-
Product
Adapter, 2.4 mm (m) to Type-N (m), DC to 18 GHz
11903A
-
The Keysight 11903A is a metrology-grade, 2.4 mm male to type-N male adapter with dc to 18 GHz operation.
-
Product
Current Loop Adapter
OP-1C
-
This adapter supports current loop communications.The kit incorporates a communications circuit with photo-coupler isolation and constant-current power supply of insulated type, thus realizing not only monitoring but also easy communications testing with passive or active current loop devices.
-
Product
Digitizer Adapter Module For FlexRIO
Digitizer
Digitizer Adapter Modules for FlexRIO can be used with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO to create a high‐performance instrument with customizable firmware. With sampling rates from 40 MS/s to 3 GS/s and up to 32 channels, these modules cover a wide range of requirements for both time- and frequency‐domain applications. Digitizer adapter modules also provide digital I/O capability for interfacing with external hardware.
-
Product
PCI bus Test Adapter
pcibus1b
-
All important PCI bus signals routed to pin headers for easy connection of logic analyzer. Filter assistance for logic analyzer: D-FF to delay FRAME# by one cycle. To see actual PCI data transfers, filter for FRAME2# high + FRAME# low (address phase), or IRDY# low and TRDY# low (data phase). Business card size. Notched for 5V PCI bus (can be used on 3.3V bus with mechanical modification).
