AAA Battery
See Also: Battery, Lead Acid Battery, AA Battery, 1.5V Battery, 9V Battery, Button Battery, C Battery, Coin Battery, D Battery, NIckel Cadmium Battery, Lithium ion Battery, SLA Battery, VRLA Battery, NICAD
-
Product
PXI Battery Simulator Modules
-
These PXI battery simulators are designed to simulate the power supplies of portable battery powered equipment and the single cell (model 41-753) is particularly suitable for cell phone testing. These modules can source current to simulate a battery supply or sink current to simulate a battery under charge.
-
Product
Battery Voltage Relay
BVR
-
Battery Voltage Relays supply alarm indications at precise voltages for undervoltage and overvoltage conditions. The BVR is designed to prevent damage and incorrect operation during anticipation transient conditions.
-
Product
Test Device for Bicycle Batteries
ATGF 1500/PBG
-
The ATGF 1500 is a multifunctional testing instrument for bicycle batteries and accompanying battery chargers. The easy to use ATGF 1500 is suitable for battery systems of Derby Cycle, Gazelle, Simplon and ZEG. est programs: Quick Test, Capacity Test, Recalibration.
-
Product
Battery Backup IC
-
Analog Devices offers a range of supervisory circuits that offer a complete single chip solution for power supply monitoring and battery control functions in microprocessor systems. Functions include microprocessor reset, backup battery switchover, watchdog timers, CMOS RAM write protection, and power failure warning.
-
Product
Advanced Battery Conductance/Electrical System Tester
PBT Series
-
Building upon the success of the PBT-100, the first battery conductance tester built for the professional technician's toolbox, the PBT-200 offers these additional capabilities: Shows available power in CCA in addition to condition and voltage. Bad Cell Detection. Advanced Starter Testing: Down arrow displays the captured low voltage from cranking the engine for simple starter analysis.
-
Product
Battery Cell Surge Tester
19311
-
The Chroma 19311 series battery cell surge tester is designed for testing the insulation quality between the positive and negative plates of the lead-acid battery cell. This is done by applying a high voltage surge/impulse before the electrolyte injection. Its output voltage can reach up to 6kV. It also has four terminal measurement and 200MHz sampling rate. The Chroma 19311 series has single channel (19311) and multi-channel (19311-10) tester.
-
Product
Hand-Held Battery Load Tester, Alternator and Starter Tester
6026
-
135 Amp Fix Load Cables. Recessed meter helps protect this hand-held tester from damage and ensures more accurate and reliable outputs. Features easy to use clamps with 300 Amp jaws. Lightweight and easy to use. Imported.
-
Product
Hand‐held Digital Battery Tester w/ Thermo Printer, USB port
12-1015
-
• Tests 12V Flooded, AGM, Gel Cell, Enhanced Flooded (Start/Stop Batteries)• 10 Line LCD display• Performs ground test• Checks diode ripple• Stores last 250 test series with or without power• Carrying case, printing software and USB cables included• Built-in thermal printer with thermal paper (611305)
-
Product
Scienlab Combined Battery Test Solution
SL1133A
test
Solution for testing battery cells with an output power up to ±3 kW and a voltage range up to 6 V.
-
Product
Battery Cell Insulation Tester
Chroma 11210
-
Chroma Systems Solutions, Inc.
Chroma 11210 battery cell insulation tester is an instrument used for accurately measuring leakage current (LC) and insulation resistance(IR) of battery jelly-roll/dry-cell as well as other insulation materials. In addition to standard LC/IR measurement, the 11210 has a unique function that detects partial discharge (PD) or flashover that may have occurred inside the insulation material during the high voltage insulation testing process.
-
Product
Beam Directional Power Supply Battery 40 to 120 kV
CP120B
-
This ultra-light, compact and battery operated constant potential portable X-Ray generator is the perfect tool for specific NDT applications that require repetitive short exposures. Its versatility also makes it the ideal piece of equipment for security applications. In fact, in combination with the FLATSCAN15, the FLATSCAN30 and other digital X-Ray detectors, the CP120B will – thanks to its small focal spot and constant potential X-Ray output – enhance image quality and definitely contribute to a reduced exposure time.
-
Product
Battery Load Tester
BT-100
-
Schumacher Electric Corporation
FOR EVERYDAY DIY USEEasy to operateTest load, battery condition, starter motor draw and complete charging system diagnosis.Works on 6 and 12 volt batteries50 amp load test for 6 volt batteries100 amp load test for 12 volt batteries Tests 6 and 12 volt batteries ─ up to 1000 CCATop-mounted rocker switch for easier operationSuper-grip, heavy-duty color-coded battery clampsEasy-to-read meter ─ accurate and shock resistantBaked enamel, steel case ─ ventilated to keep coolRubber insulated carrying handle ─ for comfort and safety
-
Product
EV/HEV Battery Pack Environmental Exerciser/Monitor System
-
DMC designed, built, and programmed a set of automated test stands for charging and discharging electric vehicle battery packs. The test stands also monitor the performance of these battery packs while exposed to harsh environmental...
-
Product
5V1mA Button Battery Tester
TOB-BST8-5V1mA
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channel Battery Analyzer (0.002-1mA, up to 5V) with Laptop & Software for R&D Battery Materials. TOB-5V1mA Button Battery Tester is an eight-channel battery analyzer to analyze small coin cells with a range current 0-50mah, voltage 0-5v. Each channel of the analyzer has independent constant-current and constant-voltage source, which can be programmed and controlled by computer software.
-
Product
Battery Resistance Tester
FBR-6100NT
-
Fuzhou Fuguang Electronics Co., Ltd.
FBR-6100NT Battery Resistance Tester is a new generation handheld battery tester of FUGUANG™, which can quickly,intuitively and conveniently judge the deterioration of batteries (lead-acid batteries, lithium iron phosphate batteries and nickel-cadmium batteries, etc.). It has the characteristics of high accuracy, repeat consistency and anti-interference. It is an ideal tool for rapid battery daily check.
-
Product
Battery Fault Insertion Unit
Fault Insertion Unit
The Battery Fault Insertion Unit (FIU) provides intelligent switching of cell-simulation channels for the Battery Simulator 1200. The switching capability enables simulation of open-circuit and short-to-rail fault conditions on any cell channel for the purposes of battery management system (BMS) testing. Additionally, a four-wire auxiliary input allows you to connect an external digital multimeter (DMM) instrument to any cell channel for very high-accuracy bypass current and cell voltage measurements. Each FIU provides 24 independently-programmable cell-switching channels for one or two 12-cell Battery Simulator 1200 units. Additional Battery Simulator 1200 and FIU instruments can extend functionality up to 120 series-connected cell channels.
-
Product
Battery Test Chamber
-
Thermotron Battery Test Chambers are manufactured to thoroughly test battery cells and lithium-ion battery packs. Diverse chamber sizes and types allow for a variety of battery types to be tested. Thermotron offers a variety of features to ensure the safety of the battery test chamber users while testing batteries. These features reduce the chance of an explosion and minimize the damaging effects of a spark-induced explosion.
-
Product
Battery Testing
-
Electric vehicles (EVs) rely on batteries as their primary source of energy storage. As battery packs require battery management systems (BMS) to operate safely and reliably, it is vital to test control algorithms for state of charge (SoC) estimation or cell balancing at an early stage.
-
Product
Battery Chargers
-
Xantrex battery chargers are micro-processor controlled for fast, accurate charging of vehicle or boat batteries in deep cycle or maintenance applications. Xantrex battery chargers are compact, light weight and easy to install.
-
Product
VoLTE Battery Test, Reference Solution
-
The VoLTE Battery Test, Reference Solution is a fully automated test solution for chipset vendors and device makers who need to follow operators’ VoLTE battery acceptance test plans.
-
Product
Battery Management Systems
-
A BMS is the intelligent component monitoring and managing any lithium-ion battery pack. It is the brain behind the battery and has a key role in its levels of safety, performance, charge rates, and longevity.
-
Product
MINI Battery Discharger & Capacity Tester
IDCE-4815CT
-
Fuzhou Fuguang Electronics Co., Ltd.
IDCE-4815CT can provide 0-150A (steps:1A) adjustable current for different test requests
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
-
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Automatic Batteries with Filters with Thyristors
BATLVFS600
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
Product
High Voltage Benchtop Battery Tester 1000V Max input
BT3564
-
Hioki benchtop battery testers support simultaneous high-speed measurement of the internal resistance and battery voltage of EV and PHEV battery packs. The BT3564 Battery HiTester can measure pack voltage and total resistance, as well as bus bar resistance up to 1000V.
-
Product
Battery Probes
-
C.C.P. Contact Probes Co., LTD.
CCP offers a variety of different high current battery testing probes.
-
Product
Temperature & Battery Testing
-
Conducted to determine how a battery performs under different temperature ranges.
-
Product
Extended Battery Banks
-
Falcon Electric’s extended battery banks provide extra battery runtimes from minutes to hours with our SSG and SSG-RP online industrial UPS systems. The rackmount banks are easily daisy-chained with DC plug-and-play connectors. Simply determine your application requirements and select one of these battery bank options.
-
Product
Battery and DC System Testing
-
HAOMAI Electric Test Equipment Co., Ltd.
Testing for battery and DC power systems.
-
Product
HEV Battery Reconditioner
-
Battery reconditioning and cell balancing is a well understood process for NiMH batteries. The procedure was initially developed for NiCad batteries decades ago. NuVant Systems has simplified the process to bring electrochemistry to the streets. The EVc unit is a push-one-button-after-wire-up system for small shops to large vehicle operators.
