Data Acquisition Software
Data acquisition software is designed to record, store, present and analyze data collected from sensors and other digital devices. (globalspec.com)
-
Product
USB to RS-422/RS-485 Converter
ND-6530
Data Acquisition Module
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
HDD-8261, 4 TB, 6-Drive, PXI Data Storage Module
784191-01
Data Storage
4 TB, 6-Drive, PXI Data Storage Module - The HDD‑8261 in-chassis PXI Express high-speed data storage module features an onboard PCI Express SATA controller. The module fits into a PXI Express chassis, and it occupies only three PXI slots. With the HDD‑8261, you can choose between hard-disk drives (HDDs) or solid-state drives (SSDs) for increased ruggedness. It is ideal for field testing or signal recording applications. You can use this module to not only stream high-speed data, but also to easily move data between multiple test setups or supplement the PXI system controller’s storage capacity.
-
Product
I-Pi SMARC IoT Development Kit Based On Intel® 7th Gen Atom® X7433RE Quad-Core SoC
I-Pi SMARC Amston Lake
Software Development Kit
The I-Pi SMARC Amston Lake is a SMARC-based edge solution devkit powered by power-efficient Intel Atom x7433RE quad-core SoC with integrated Intel UHD graphics with 32 EUs, deep learning inference capabilities, industrial grade durability and comprehensive high-speed interfaces.
-
Product
PXIe SSD Storage Unit
DM-4M.2-3U
Data Storage
The Big River™ DM-4M.2-3U PXI Express storage unit provides up to 3.8TB* of M.2 SSD storage capacity. With a PCIe x8 Gen3 host interface, the DM-4M.2 delivers high-speed data rates for sequential writes of 3.25GB/s** and sequential reads of 3.41GB/s** to PXI Express based systems. The single slot design of the DM-4M.2 increases the availability of valuable chassis space, allows for maximum storage flexibility. The DM-4M.2 complies with PCIe Gen3 protocol standards. The product is commonly used in the industrial control, test and measurement fields. The DM-4M.2 operates under Windows, Linux, Unix, Solaris and VxWorks.
-
Product
USRP-2954, 10 MHz to 6 GHz, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device
783153-01
Software Defined Radio Device
The USRP-2954 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and shorten time to results. You can prototype a range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding. The USRP-2954 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) reference clock. The GPS disciplining delivers improved frequency accuracy and synchronization capabilities.
-
Product
Automation Product Software Development Kit
APS SDK
Software Development Kit
APS means “Automation Product Software”. APS library provides users a uniform interface to access all of ADLINK products which support it. It can cover many automation fields especially in machine automation. The most important component in machine automation is motion control. APS library was first born with motion control which co-working components such as system platform management, field bus communication function, general digital input/output, general analog input/output and various counter/timer supports are all built-in components in APS. The APS library will be an all-in-one solution in automation field of ADLINK products.
-
Product
PXIe-8267, 4 TB, M.2, PXI Data Storage Module
785308-01
Data Storage
PXIe, 4 TB, M.2, PXI Data Storage Module - The PXIe-8267 PXI Express high-speed data storage module features large-capacity, high-throughput storage in a single PXI Express slot. With M.2 solid-state drives, the PXIe-8267 is ideal for stream-to-disk or stream-from-disk applications requiring sustained, reliable data throughput such as high-speed signal intelligence, RF record and playback, and multi-sensor data acquisitions systems.
-
Product
COM Express Type 10 Starter Kit Plus
COM Express Type 10 Starter Kit Plus
Software Development Kit
The COM Express Type 10 nanoX Starter Kit Plus consists of a COM Express Type 10 core module reference carrier board that provides two PCIe Mini Card slots, 2 RJ-45 LAN ports, 2x USB 3.0, 2x USB 2.0, 1x USB client, 2x DB-9 COM, 1x SD card socket, and Mic/Linein/ Line-out. ADLINK also provides additional development tools including a verified 10.1" LVDS panel (optional), power supply, thermal solution and cabling accessories.
-
Product
4x 3U OpenVPX MOSA Data Concentrator Unit
SIU34-DCUVARM-01
Data Concentrator Unit
SIU34-DCUVARM-01 is a Modular Open Systems Approach (MOSA) DO-178C & DO-254 Certifiable Data Concentrator Unit (DCU) with low power high performance OpenVPX Xilinx UltraScale+ SBC with Quad Core ARM Cortex -A53, 8 GB DDR4 SDRAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet, USB 3.0, FIPS-140-3 Level 3 Cyber Security, and Single Event Upset support.
-
Product
I-Pi SMARC Development Kit based on NXP® i.MX 8M Plus Quad Arm® Cortex-A53 Processor
I-Pi SMARC IMX8M Plus
Software Development Kit
The I-Pi SMARC IMX8M Plus is a SMARC-based smart solution development kit powered by NXP i.MX8M Plus (Quad-core Arm Cortex-A53) processor with a Neural Processing Unit (NPU) at up to 2.3 TOPS.This is the first SMARC R2.1 development kit focused on machine learning, vision, advanced multimedia, and industrial IoT with high reliability. As such, it supports dual image processors and two camera inputs for an effective Vision System, as well as applications beyond, including smart homes, building cities, and industry 4.0.
-
Product
Data Acquisition System
Pixie-16
Data Acquisition Module
The Pixie-16 is a data acquisition system for nuclear physics and other applications requiring coincident radiation detection with large number of channels.
-
Product
Spring Testers
-
Imada offers manual or motorized spring testers in vertical or horizontal configurations.Lever-operated manual systems enable rapid compression and tension spring testing.Wheel-operated manual systems enable slower, more precise movement with the hand wheel.Motorized compression testers offer the most control and highest degree of repeatability with the ability to set a constant test speed and range of movement.All spring testers can be configured with a digital force gauge with data output for analysis by data acquisition software. An optional digital distance meter to measure displacement is available.
-
Product
USRP‑2930, 20 MHz Bandwidth, 50 MHz to 2.2 GHz, Included GPS-Disciplined OCXO, USRP Software Defined Radio Device
781910-01
Software Defined Radio Device
20 MHz Bandwidth, 50 MHz to 2.2 GHz, Included GPS-Disciplined OCXO, USRP Software Defined Radio Device - The USRP‑2930 is a tunable RF transceiver with a high-speed analog‑to‑digital converter and digital‑to‑analog converter for streaming baseband I and Q signals to a host PC over 1 Gigabit Ethernet. It also features a GPS-disciplined oscillator (GPSDO) with PPS accuracy of ±50 ns. You also can use the NI USRP‑2930 for the following communications applications: white space; broadcast FM; public safety; land-mobile, low-power unlicensed devices on industrial, scientific, and medical (ISM) bands; sensor networks; cell phone; amateur radio; or GPS.
-
Product
USRP-2955, 10 MHz to 6 GHz, 80 MHz Bandwidth, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device
785264-01
Software Defined Radio Device
The USRP-2955 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless receiver systems. It is designed for over-the-air signal acquisition and analysis. It features a two-stage superheterodyne architecture with four independent receiver channels and shares local oscillators for phase-coherent operation. It also offers a Kintex-7 FPGA programmable with the LabVIEW FPGA Module. With these features, the USRP-2955 has the RF and processing performance for applications such as spectrum monitoring, direction finding, signals intelligence, wideband recording, and radar prototyping. The USRP-2955 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) Reference Clock, which improves frequency accuracy and synchronization.
-
Product
I-Pi OSM Development Kit Based On NXP® I.MX 93 Dual-Core Arm® Cortex-A55 & M33
I-Pi OSM IMX93
Software Development Kit
The I-Pi OSM IMX93 is an OSM-based smart solution development kit powered by NXP i.MX93 (dual-core Arm Cortex-A55 & Arm Cortex-M33) processor with an in-SoC Arm Ethos-U65 microNPU (Neural Processing Unit).
-
Product
8-CH Relay Output Module
ND-6063
Data Acquisition Module
- 8-CH relay outputs- Output Type: 8 Form A- Contact Rating: AC: 0.5 A / 125 V; DC: 1 A / 30 V or 0.3 A / 110 V; ON/OFF Interval Time: 3 ms- Breakdown Voltage: 500 VAC (50/60 Hz)
-
Product
16-CH 12-Bit 110 kS/s Multi-Function DAQ Card
PCI-9112
Data Acquisition Module
- Supports a 3.3 V or 5 V PCI bus- 12-bit A/D and sampling rate up to 110kS/s- 16-CH single-ended or 8-CH differential inputs- On-board A/D FIFO
-
Product
Systems And Data Acquisition
-
From sensor to software: Kistler offers complete systems for selected applications.
-
Product
Autonomous Data Acquisition
Triggering
-
Vibration Research Corporation
In VR Mobile, set up actions to occur automatically following an event; after the trigger, the ObserVR1000 will record data without intervention. This feature saves time and ensures accuracy and consistency during recording.
-
Product
Data Acquisition
-
We offer a full range of high quality data acquisition systems, starting from small, single or double channel systems, up to big multichannel systems. The smaller systems can identify themselves to the operating system as soundcards, for the bigger systems we deliver MatLab and DasyLab application drivers.
-
Product
Data Acquisition
-
Sound, vibration, status and reference variables, voice, audio data and more: HEAD acoustics is setting the standard in data acquisition. We offer flexible systems for mobile applications and operation in the laboratory. Our data acquisition systems can also be expanded flexibly using various software and hardware modules.
-
Product
16-Ch, 24-Bit Thermocouple Input IDAQ Module
iDAQ-868
Data Acquisition Module
Hot-swappable in iDAQ system16-channel thermocouple sampling24-bit resolution50/60Hz rejection filter availableWide range of thermocouples supportedIsolation protection up to 600VRMS
-
Product
FR-Net Data Acquisition
-
FRnet Protocol developed by ICP DAS is an easy to use industrial field bus offering high-speed deterministic I/O control, real I/O synchronization capabilities, and non-protocol communication. We provide FRnet remote I/O modules and high speed controllers.
-
Product
16/32 -CH 16-Bit 250/500 KS/s Multi-Function DAQ Cards with Encoder Input
PCI-9222/9223
Data Acquisition Module
The ADLINK PCI-9222/PCI-9223 is a 16-bit, 16/32-CH, 250/500 KS/s high performance DAQ card with 8 different input ranges. It also features 2-CH 16-bit analog outputs capable of a 1 MS/s update rate, 2-CH encoder inputs, and programmable function I/O. The software-programmable function I/O supports a variety of applications, including TTL digital I/O, high-speed DIO, general-purpose timer/counter, pulse generation, and PWM output. Analog input, analog output, and function I/O at full speed simultaneously, and multiple cards can be synchronized through the SSI (System Synchronization Interface) bus if users need more channels than a single board can provide. Ideal for mixed-signal tests, laboratory research, and factory automation, PCI-9222/PCI-9223 is the best single-board solution on the market providing the best integration capability of multiple tasks with high performance and an affordable price.
-
Product
16-CH 12/16-Bit 100 kS/s Low-Cost Multi-Function DAQ Cards
PCI-9111 Series
Data Acquisition Module
ADLINK PCI-9111 series are 16-CH, 100 kS/s low cost multi-function DAQ card. The PCI-9111 series feature flexible configurations on analog inputs. A RC filter is implemented on each A/D input channel for user to attenuate or filter input signal. The PCI-9111 series provide analog inputs with 5 programmable input ranges for bipolar inputs. The PCI-9111 series also support automatic analog input scanning. PCI-9111DG provides 12-bit A/D resolution while PCI-9111HR provides 16-bit A/D resolution. The PCI-9111 series also feature 1-CH 12-bit analog output, 16-CH TTL digital inputs and 16-CH TTL digital outputs. ADLINK PCI-9111 series deliver cost-effective and reliable data acquisition capabilities, and is ideal for a broad variety of applications.
-
Product
MQTT Data Acquisition
-
MQTT is a method of Machine to Machine (M2M) communication by writing and retrieving application-specific data (messages) to and from queues, without having a private, dedicated connection to link them. It simplifies and accelerates the cloud-based integration of diverse applications data between IIoT devices under assured, secure and reliable exchange of information circumstance. Using MQTT in IIoT devices not only dramatically simplifies the creation and maintenance of Industrial application but also makes connectivity for the “internet of things” and mobile devices easily, and achieve the smart automation based on industry 4.0.
-
Product
64-Channel 1MSa/s USB Modular Multifunction Data Acquisition
U2331A
Data Acquisition Module
The U2331A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2331A to simulate simultaneous analog input acquisition.
-
Product
Network-Ready Data Acquisition System
DAPserver 500
-
The DAPserver 500 and DAPserver 502 – and the DAPserver 500R and 502R, the latter "R" models for rugged environments – serve as fully integrated test, measurement, and control products. Built with experience gained over many years of integrating third-party hardware, these high-performance combined systems are now available as standard products,
-
Product
3 Function Slot MOSA Nano Data Concentrator Unit (DCU)
NIU3A-DCU-01
Data Concentrator Unit
NIU3A-RDC-01 is a Modular Open Systems Approach (MOSA) Data Concentrator with low power high performance ARM Cortex -A53 processing. 8 GB RAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet.
-
