Filter Results By:
Products
Applications
Manufacturers
Digital Power Meters
Measure the optical, microwave or electrical amounts of energy.
See Also: Power Meters, RF Power Meters, Magnetic Field Strength Meters
- Pickering Interfaces Inc.
product
Quad 4-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-001
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
product
RF Milliwatt Meters
Type NDB-2 and NDB-3
National RF’s Type NDB-2 and NDB-3 RF Milliwatt Meters are affordable pieces of test equipment for both the RF laboratory and the home experimenter. Both provide a digital reading of RF power in dB reference 1 milliwatt of power into a 50 ohm load (i.e. 0 dBm). The circuitry consists of a low noise logarithmic amplifier that drives a digital A/D converting meter circuit. The lowest power levels that can be read are about –73 dBm (approximately 40 microvolts or .00000003 milliwatts). The maximum power input should not exceed 10 milliwatts (+10 dBm or .010 watts) when inputed without attenuation. An internal attenuator is provided and described in the next section.
-
product
Live-Dead-Live Meter Verifier
LDL-1200
The Live Dead Live (LDL) Meter Verifier is a small, lightweight, robust, portable, handheld power supply. It supplies just under 150 volts, AC (rms) or DC with a maximum current of less than 5 mA at rated voltage. The LDL-1200 Meter Verifier is specifically designed to facilitate voltage verification tests on most digital multi-meters, electronic voltage detectors, voltage testers, neon test lights, tic tracers and other commonly used electrical voltage test apparatus, while keeping the user as electrically safe as possible with its extremely low “volt-amp” output.
-
product
AC/DC Single Phase Digital Power Meter 6 kHz
T3PM1006
AC/DC Single Phase Digital Power Meter 6 kHz.
-
product
Pump & Motor Testing Instruments
Aarohi Embedded Systems Pvt. Ltd
AAROHI Pump and Motor Testing Instruments - dynanometer, stator rotation direction detector, digital RPM meter, DC power analyzer, motor analyzer.
-
product
Digital Power Meter (AC & DC Model)
LS2012
• Measure Vrms, lrms, W, PF/Hz; • Measure AC, DC, AC+DC; • Automatic selecting, out of limit alarming, advance the work efficiency; • Voltage range: AC: 5-600V, DC: 1-600V. Current range: AC&DC: 0.005-20A with high measure accuracy. Auto range; • Accuracy: ± (0.4%reading + 0.1%range + 1digit).
-
product
Power Meters
Teledyne Test Tools range of digital power meters are for single-phase (1P/2W) AC power measurements with a test Bandwidth ranging from DC, 0.1 Hz to 100 kHz. The T3PM1006 model features a 4” TFT LCD screen with a five-digit measurement display. It offers 19 power measurement parameters to choose from, integration measurement function, front/rear panel input terminals, and various communication interfaces to help users to make convenient and accurate power measurement. The T3PM1100 model offers DC, 0.1 Hz ~ 100 kHz test bandwidth, 16 bits ADC, and 300 kHz sampling rate. It features a 5” TFT LCD screen with a five-digit measurement display. It also has options to display waveform (voltage/current/power), the integration measurement function, harmonic measurement and analysis of each order (meeting the IEC 61000-4-7 harmonics measurement requirements at 50/60 Hz), external sensor input terminals, and various communication interfaces to help users to make convenient and accurate power measurements.
-
product
Digital Multimeter, USB Interface, 20000 Count, True RMS, Auto Range, 4.5 Digit
72-7730A
Digital multimeter is a 20,000 counts and 4-1/2 digits with steady operation. The meter can measure AC voltage and current, DC voltage and current, resistance, capacitance, temperature frequency, diodes, continuity, 4 to 20mA loop, Max/Min, relative mode but also has data store, data recall, AC true RMS, AC+DC, low battery display, double display backlight, automatic power off and full overload protection.
-
product
Digital Power Meter, 30A
Chroma 66205
Chroma Systems Solutions, Inc.
66205 is the 2nd generation of the 66200 series power meter designed specifically for single channel measurement. Its state-of-the-art design is capable of providing highly accurate power measurements to meet the requirements of IEC 62301/EN50564 standards. Functionality improvements of the 66205 increase power measurement capabilities to a wider range of applications.
-
product
High Performance Programmable AC Power Supply
IT7600 Series
IT7600series high performance programmable AC power supplies, adopt advanced digital signal processing technology, with frequency up to 10-5000 Hz, built-inall-round power meter and large-screen oscilloscope function. Power up to 54kVA and support master-slave parallel, which can provide high-capacity single-phase or three-phase AC output.
-
product
Analog Optical Power Meter - MATRIQ
1500 Series
The Power 1500 Series analog power meter brings cost-effective test and measurement. The Power 1500 provides logarithmic analog output as well as a digital optical power meter for applications that require real-time feedback.
-
product
Wideband Digital RF Watt/VSWR Meter
RF ONE 3029
The RF One Power Meter is a very versatile instrument covering both analog and digital carriers in an extremely wide frequency range from 30MHz to 6GHz. The RF One is capable of measuring forward and reflected power in the range of a few milliwatts up to 500 Watts. The internal operating system controls measurement, display and the I/Os allowing serial communication to PC, USB to memory stick and USB Serial communication. The I/O options are used to write plots to either memory sticks or to a connected PC, the I/Os can also be used to operate the instrument, giving commands and receiving data. For documentation reference the instrument has a real time clock. Multilayer menus are used to setup and control the operation of parameters. The RF One instrument is small, handy and light weight battery operated with more than 3 hours of continuous operation on the internal NiMh cells. Feature with XML data handling and application viewer is included. Accessory kit with soft carrying bag, car charger and coax adapters for standard types.
-
product
Multi-Channel Digital Power Meters
Chroma 66203/66204
Chroma Systems Solutions, Inc.
Chroma’s Digital Power Meters are designed for both single-phase and multiple phase measurements of AC power signals and related parameters common to most electronic products. Instead of traditional analog measurement circuits the 66200 Digital Power Meter uses state-of-the-art DSP digitizing technology. The internal 16 bits analog/digital converters with sampling rates of up to 200KHz provide both high speed and high accuracy measurements which is unprecedented within the industry for this class of power meters current on the market.
-
product
Electric Fence Chargers
Mark 8
Parker McCrory Manufacturing Co.
The all new Mark 8, low impedance fencer gives you the stock holding power that you have always wanted. Shocks right through wet weeds or brush and over extremely dry ground. Features Parmak`s exclusive built-in DIGITAL performance meter that tells you the exact condition of the fence. Takes the guesswork out of electric fencing. 100% solid state, with all new low impedance, uni-junction circuitry. No moving parts. Ideal for use with high tensile single or multi-wire fences. New color coded fence and ground terminals. Red to the fence and Black to ground. The Mark 8 operates for less than 7 cents a month at 7 cents per kwh. Fuse protection, with new built-in lightning arresters. Full 3 year warranty covers damage caused by lightning.
-
product
Portable Three Phase Phantom Load Power Source
SY2103
Hong Kong Songyang Industrial Ltd.
The new SY2103 series portable three phase phantom load stable power source, designed from new digital wave compound technology and according to International Standard, is newly intelligent equipment for energy meters. The equipment includes voltage/current source & standard meter, operated easily through front panel to preset directly all data of meter under test and test process.
-
product
AC and DC Voltage Divider
WAFRC
Wuhan Sangao Electrical Test Installations Limit Co.
AC and DC voltage divider, Mainly composition by the high stability of passive resistance capacitance voltage divider and high precision digital kV table. The divider is passive resistance capacitance, Connected digit kV meter by coaxial cables. Which can be directly read out the AC, DC data measured from the table. This instrument has high precision, convenient operation, can be used instead of the electrostatic voltmeter. Device and the measuring line, power line, manual loaded box in light aluminum alloy, easy to carry and use. This equipment is mainly used for AC and DC high voltage measurement, and is suitable for power system's field measured and Institutions of higher learning laboratory's AC and DC high voltage measurement.
-
product
Power Meters
Chroma Systems Solutions, Inc.
Chroma’s Digital Power Meters are designed for both single-phase and multiple phase measurements of AC power signals and related parameters common to most electronic products. Instead of traditional analog measurement circuits the 66200 Digital Power Meter uses state-of-the-art DSP digitizing technology. The internal 16 bits analog/digital converters with sampling rates of up to 200KHz provide both high speed and high accuracy measurements which is unprecedented within the industry for this class of power meters current on the market.
-
product
DIGITAL PHASE ANGLE METER
GF211B
Beijing GFUVE Electronics Co.,Ltd.
GF211B onsite handheld digital phase angle meter can measure alternating voltage, alternating current, frequency, phase angle, active/reactive power, power factor and so on.
-
product
Digital Power Meter (Harmonic Analyzer Model)
LS2010
• Measure Vrms, lrms, W, PF, Hz; • Harmonic distortion analysis for voltage & current, display total harmonic and 0-50 times; • Component harmonic, selectable for absolutely or relatively harmonic display; • Voltage range: 10.0-600.0V, Current range: 0.010-20.00A, Auto range; • Accuracy: ± (0.4%reading + 0.1%range + 1digit); • Simultaneously display Vrms, lrms, W, PF value on 4 windows, suitable for production line; • Can test every kinds of curve; Print both data & curve; • Communication port for PC, run under WinXP or Win7.
-
product
Digiair PRO
Frequency range of 45-860MHz.• The meter to use for easy Digital terrestial installations.• Very sensitive, easy to maximize weak and strong signals.• Signal level reads out in dBuV.• Presents one channel readout with high resolution or six channels.simultaneously or the complete spectrum.• Built in beeper (pitch tone) and maxhold function.• Aerial power output, 0, 5 and 12V.• Built in, rechargeable battery.• Power supply and car-charger enclosed.• Carrying-case enclosed.• Small and handy design.• Made in Sweden.
-
product
Compact Ultrafast 50-50,000 sccm Mass Flow Controller/Meter
C-Series
The C-Series Mass Flow Controller (MFC) is a compact, fast-response model using a Micro-Electro-Mechanical Systems (MEMS) based flow sensor for non-corrosive gas applications. It is available in Full Scale flow rates from 50 sccm to 50 slm (N2 equivalent) with a control range from as low as 0.1% of Full Scale up to 100% of Full Scale and is also available as a flow meter. Analog (0 to 5 VDC) or digital (RS485 or Modbus TCP/IP) communications interfaces are available. Required power supply voltage is 24 VDC nominal.
-
product
IC & Transformer
Mornsun Guangzhou Science & Technology
MORNSUN launched the self-designed electronic integrated circuits according to the different product lines, types of the integrated circuit include AC/DC power supply control ICs, DC/DC power supply control ICs, interface ICs, start-up ICs, contactor power saving controller ICs and digital isolator ICs. MORNSUN IC chip can be widely used in industrial equipment, process control, data acquisition system, building automation, smart meter, etc. Adopting MORNSUN's AC/DC transformers and DC/DC transformers, with the use of its control ICs, can achieve wide voltage input flyback power supply design with multiple protection functions and superior EMI performance. We hope that those power transformers along with the integrated circuits & chips electronics can be an ideal fit for your application needs.
-
product
Field Test Kit
621
TESCO’s light-weight, 50 Amp Field Meter Test Kit (Catalog No. 621) with Power Factor, has been designed to reduce the weight of field test equipment to the lowest possible limit. The carrying case is fabricated from durable powder coated aluminum. The total weight of the meter test kit including leads, and digital reference standard is only 25 lbs! The test kit also incorporates ample storage space for the cable set.
-
product
Digital Power Meter
It is a power meterwith superior performance an powerful functions. In addition, it has simple structure and operation.
-
product
Regenerative AC Load
61800
Chroma Power Electronics Test Solutions not only apply in the industries of Information Technology, Communication, Aerospace and National Defense, but also in energy efficient products such as Hybrid Automobiles, LED luminance devices, solar and fuel cells that are developed aggressively under the pressure of natural resource constraints. Chroma has a wide variety of instrumentation including AC Power Sources, DC Power Supplies, DC Electronic Loads, AC Electronic Loads, Digital Power Meters, and Automatic Test Systems that are ideal for power input/output terminal tests and dynamic simulation.
-
product
Linear Bench Power Supplies Local Control, Ultra Low Ripple/Noise
Series MSK
Kepco's MSK linear power supplies provide a selection of five models, offering 100 Watts of stable benchtop power. They use a high gain linear (series pass) stabilizer circuit for ultra low noise and low ripple output, good stability, and accurate resettability, and they are MIL-STD-461 compliant.MSK's "Preview" switch (d-c on-off) allows voltage and current to be pre-set with the digital meters displaying the set values. At "d-c off," no voltage is applied to the output terminals and no load current needs to be drawn to set the current limit. At "d-c on," the set voltage is applied to the output terminals, the appropriate mode indicator illuminates and the meters indicate actual voltage and current.
-
product
Digital Ethernet Power Meters
FU2200A
Beijing GFUVE Electronics Co.,Ltd.
Digital Ethernet power meter with data logger is a three-phase multifunction power and energy meter manufactured by GFUVE. It provides excellent value for monitoring power and energy management systems. It may be used as data gathering devices for intelligent power distribution or plant automation systems. All monitored data is available via a standard digital RS485 communication port, which is based on the Modbus RTU protocol.
-
product
Touch Screen Mini OTDR, 1310/1550nm
TR1200 Series
Shenzhen Sharingtek Communication Co., LTD
1. 4.3-inch multi-touch capacitive screen support zoom function screenshot2. Intelligent multi-function 12-in-one functional module: automatic OTDR expert OTDR event map optical power meter visible fault locator adjustable light source optical loss test RJ45 sequence test RJ45 length test RJ45 digital tracker flashlight end face detection (optional)3. Automatic OTDR no complicated settings one-key test4. Expert OTDR professional measurement mode simultaneous display of curve list and MAP view5. Event blind zone 2.5m attenuation blind zone 8m measuring range up to 100KM6. Support optical test with optical signal less than -5dBM high isolation bilateral filter technology7. Support automatic saving SOR file format 8G storage capacity 200000 records can be stored8. Support Type-C charging interface 4000mAh polymer battery battery life is more than 12 hours
-
product
Dual Source Energy Meter
Directly replaces 2 energy meters Sensing dual source through 240V connection Dual row display switches based on the source Displays basic and most of the power parameters Optional digital output separately for EB or DG parameters
-
product
Clamp Meters
The clamp meter is ideal for measuring AC or DC voltage. The instrument is irreplaceable for inspection work and maintenance in various industrial applications, in research and development, in residential applications and in many small businesses or households. The PCE line of clamp meter is made according to the highest industry standards and very important: PCE offers instruments that are usable in all workspaces (equipped with very small or even very large jaws), the results are reliable and the clamps are easy to use. Every clamp meter is manufacturer calibrated and can be certified to ISO or NIST - hold a PCE clamp meter in your hands and you can feel the quality immediately.PCE offers a variety of models: Voltage detector, voltage leak detector, voltage power detector, metric detector and current detector. In addition many clamp meters are able to measure other parameters, such as capacity, resistance and power - power through clamps directly or by handheld digital instruments with external clamps (with a range of one or three stages). Very often the clamp meter is a real multimeter - so it becomes a general electrical measurement tool.
-
product
Multifunction Electrical Installations Meter
MPI-520S
The MPI-520S multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520S is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.
