-
Product
Needle Microprobe
MT-23/5HT
-
Fast-response 23 gauge needle probe, (needle length is 5 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
NI-9403, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
780179-01
Digital Module
5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The NI‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9403 for applications such as custom, high-speed counter/timers; digital communication protocols; and pulse generation. In a CompactDAQ chassis, you can use the NI‑9403 only as a static (software-timed) digital I/O module. You cannot use these modules to route timing or triggering signals.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m HV, Exit Towards Pin 1
A050DM5-C-HA050
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
2 X 1 SCSI Switch For Rack Mount Or Tabletop
MODEL SS1
-
The SS1 SCSI Bus Switch allows two hosts to share peripherals or one host to access either of two sets of peripherals. Each port may be SE, HVD or LVD. Switching from one port to the other may be accomplished: a. locally with the front panel switch, b. remotely with a momentary dry contact closure, or c. remotely via the RS-232 port. A software template for the RS-232 port is included in the User Manual. In all cases switching does not occur until "bus free."
-
Product
Gauge Type T Thermocouple Wire
W-TW-44TEF
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Isolation Amplifiers
-
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
Product
PXI-2571, 66-Channel, 1 A, SPDT PXI Relay Module
778572-71
Relay
66-Channel, 1 A, SPDT PXI Relay Module—The PXI‑2571 is a general-purpose switch module that features independent single‑pole double‑throw (SPDT) Form C armature relays. Each relay channel has a normally closed (NC), normally open (NO), and common (COM) terminal.
-
Product
NON CONDUCT INFRARED THERMOMETER
IBL-MT4
-
International Biological Laboratories
This Digital Non Contact type Infra Red Thermometer with laser sensor uses temperature sensor of Thermopile 6 - 14 mm and measures temperature from -50 to 280 Degree C and also in Fahrenheit scale.
-
Product
Scienlab Measurement & Control Module
SL1062A
Communications Module
The Measurement & Control Module SL1062A is portable temperature measuring module for record thermocouple - temperature sensors of type K for a temperature range of -100 to +1300 °C and with 16 channels. The module can be used either as a stand-alone device or as extension for a Scienlab Battery Test System.
-
Product
FieldFox C Handheld Microwave Analyzer, 10 GHz
N9915C
-
Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth. Measure all four S-parameters simultaneously with 115 dB dynamic range. Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup. Perform over-the-air measurements for 5G NR and LTE. Use GPS/GNSS for geolocation and timestamping.
-
Product
PXI Software
-
Keysight modular products include software tools to help you quickly access your test equipment and make measurements. The Keysight IO Libraries Suite allows you to display and configure all of the modules in your system such as LXI, VXI, PXI, AXIe and USB. In addition, software drivers support the most common programming environments such as Visual Studio, C, C++, Visual Basic, MATLAB and LabVIEW.
-
Product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-01
Voltage Output Module
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
Product
DC/AC Inverter 4000 W
ODS-3000-7177-T
-
DC/AC inverter with 4000 W from Premium | input ranges 77 - 138 VDC | output 230 VAC | operates in temperatures from -25 to +70 °C | approved for EN45545-2 fire and smoke | railway version
-
Product
Air Temperature Probe
U1183A
-
Measure dryer, transport pipe, and surrounding air temperature within the range of -50°C to 800°C.
-
Product
LGA 1151 Intel® Xeon® E & 8th/9th Generation Core™ MicroATX Server Board with 4 DDR4, 4 PCIe, 6 USB 3.1, 8 SATA3, Quad/Dual LANs, IPMI
ASMB-586
-
- LGA 1151 Intel® Xeon® E and 8th/9th generation Core™ i7/i5/i3 processors with C246 chipset- DDR4 ECC/Non-ECC 2666/2400/2133 MHz UDIMM up to 128GB- One PCIe x16, two PCIe x4 and one PCIe x1 slots- Triple displays - DVI-D, VGA and HDMI 2.0 ports- Eight SATA3 ports and six USB 3.1 ports- 0 ~ 60° C ambient operating temperature range
-
Product
7.5W to 100W - Single Output
DSP Series
-
*Low Profile for Building Automation*5V to 24V Outputs*Wide Range AC Input*-25°C to +71°C Operation*Convection Cooled*UL 1310 Class 2 Compliant*Class II Double Insulation
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 0.5m, HV
40-972-037-0.5m-FU-HV
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
NI-9239 , ±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
780181-01
Voltage Input Module
±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9239 performs differential analog input. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating. Designed for both speed and accuracy, the NI‑9239 is an effective general-purpose analog module because of its resolution, sample rate, and input range.
-
Product
Oxygen Analyzer
Rapidox 2100
-
The Rapidox 2100 is a high-performance oxygen (O2) analyser fitted with a rugged long-life zirconia sensor on a remote cable, together with a type K thermocouple sensor; allowing direct in-process measurement of oxygen and temperature in the sample gas. The sensors provide fast and accurate analysis over the low ppm oxygen range in harsh environments up to 650°C.
-
Product
Low Cost Emulator
EB-C251
-
# Real-Time and Transparent C251 Emulation# supports Intel MCS?251 and Atmel/W&M/Temic C251# Uses Bond-Out Technology# Maximum Frequency Support up to 24MHz# Source-Level Debugger for C, PLM and Assembler# MS-Windows Software# Support for ROMless and ROMed Microcontrollers# 256K Internal Memory# Memory Mapping Capabilities# Real-Time Trace
-
Product
3U CompactPCI Serial M.2/U.2/SATA Storage Carrier
cPCI-A3H20
Carrier Board
- 1x NVMe M.2 and 1x NVMe U.2 drive slot- 1x optional SATA 6Gb/s M.2 drive slot shared space with NVMe U.2- Status LEDs on faceplate: drive activity, hot-swap status, user-configurable- Operating temperature: -40°C to +85°C with qualified modules- EN50155 compliant
-
Product
NI-9860, 2-Port, C Series Vehicle Multiprotocol Interface Module
783703-01
Interface Module
2-Port, C Series Vehicle Multiprotocol Interface Module—The NI‑9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI‑XNET platform, the NI‑9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while taking other data acquisition measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO chassis.
-
Product
Flash In Card
FIC Series
-
Axiomtek's FIC (Flash in Card) series complies with CompactFlash™ specification and provides complete PCMCIA-ATA functionality and compatibility. This CF card is available in memory capacities ranging from 128MB up to 32GB in standard & industrial temperature to meet the demand of critical application. The operating temperature supports standard temperature grade (0°C ~+70°C) and industrial temperature grade (-40°C ~+85°C). The FIC series is an ideal solution for industrial storage application requiring reliability, high performance, and low power consumption.
-
Product
MIL-STD-1553 A / B Test And Simulation PC / 104+ Module
PC104p-1553
-
*Dual redundant*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems*Supports ARINC429 and ARINC 664 operations
-
Product
Fanless Edge AI System With NVIDIA® JETSON™ Nano SoM, 1 HDMI, 1 GbE LAN, 1 GbE PoE And 2 USB
AIE100-903-FL
-
*NVIDIA® Jetson™ Nano with Maxwell™ architecture with 128 NVIDIA CUDA® cores*High AI computing performance for GPU-accelerated processing*Ideal for edge AI smart city applications*Optional IP42 cover kit for semi-outdoor applications*Supports one 15W GbE PoE for camera*Wide operating temperature from -30°C to +60°C*JetPack supported
-
Product
2MP Wide Temperature Range Industrial Grade HDR Camera
e-CAM20_CU0230_MOD
-
e-CAM20_CU0230_MOD is a 2MP high performance, HDR Camera Module with excellent low light performance. It is based on AR0230AT CMOS Image sensor from ON Semiconductor®. It has an ability to stream seamlessly at wide temperature range (-40 to 105°C) which is suitable for Automotive application. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement. e-CAM20_CU0230_MOD has a dedicated, high-performance Image Signal Processor chip (ISP) that performs the entire Auto functions (Auto White Balance, Auto Exposure control).
-
Product
Mechanical Replacement Oscillator
MRO Series 3.05” x 2.02” x 1.62”
-
*Connectorized Package *Replaces Oscillators in Microwave Radios *Serially-Programmable *Manually Fine-Tuned *High Stability, <±1ppm (-10°C to +70°C) *Non-Volatile Memory
-
Product
Cable Assembly, 50-Pin D-Type, Male to Male, 2m HV, Exit Towards Pin 1
A050DM5-050DM5-HA200
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Voltage Controlled Oscillator Assembly With Heater
-
Teledyne RF & Microwave has designed a Voltage Controlled Oscillator to replace an existing application. The oscillator covers the 520 to 560 MHz frequency range. The oscillator provides +10 to +13 dBm output power. The oscillator has internal heaters designed to maintain the oscillator assembly at constant temperature. The unit operates over the 0° to 60° C temperature range with ~200 KHz frequency variation due to temperature variation.
-
Product
3.5" Embedded SBC With Intel® Pentium® Processor N4200 & Celeron® Processor N3350, VGA/LVDS, Dual LANs And Audio
CAPA318
-
The CAPA318 features the Intel® Pentium® processor N4200 or Celeron® processor N3350 (codename: Apollo Lake) with low power consumption. The integrated 3.5-inch embedded board is highly expandable and customizable. It comes with RS-232 ports, USB 3.0 ports, USB 2.0 ports, IN/OUT digital I/O ports, VGA port, LVDS port, and Gigabit Ethernet ports with Intel® i211AT Ethernet controller. For storage needs, the CAPA318 provides one SATA-600 socket and one mSATA interface. Additionally, Its compact and fanless design makes it perfect for use in space constricting environments. Additionally, the 3.5” single board computer can handle a wide operating temperature range from -20°C to +70°C (-4°F to +158°F) and requires +12V DC power input to ensure operational stability in a variety of harsh environments. This cost-effective 3.5” embedded motherboard is suitable for IoT/M2M related applications, industrial control, self-service terminals, digital signage, POS/kiosk displays, just name a few.
