Serial Data
-
Product
Digital Serial Data Audio Interface
PIO-9216
-
For accurate testing of devices that use the I2S, Left Justified, Right Justified and TDM audio data formats.
-
Product
A Serial Data Link Monitor for Windows
Listen
-
Listen is a Data Link monitor designed to assist debugging & troubleshooting serial communications links. Listen utilizes standard Windows COM port drivers to tap into RS-232 transmit signals for monitoring bi-directional communications between two devices.
-
Product
Handheld Serial Data Analyser
SDA-02
-
Non-intrusively displays, captures and analyses electrical asynchronous data. Directly accepts RS232, RS485/422 and CMOS/TTL signal levels. Modbus over Serial Line protocol capability (RTU & ASCII), automatically checks & generates CRC/LRC, can act as master or slave.
-
Product
1 Channel, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTD
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
16 GHz Differential Probe with ProLink Interface
DH16-PL
Interface
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
CompactPCI Serial Backplanes
-
CompactPCI Serial (PICMG CPCI-S.0) supports high-speed serial data transmission of up to 12 GB/s. This means excellent computing power in your applications and incredible precision for automated work processes.
-
Product
Bit Synchronizer Daughterboard Rates up to 25 Mbps
LS-40-DB
-
The Lumistar LS-40-DB Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digital design assures a high performance, consistent product, with excellent reliability and long-term stability.
-
Product
4 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTF
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
WaveMaster Oscilloscope, 4 GHz Bandwidth, 4 Input Channels, 40 GS/s Max Sample Rate
WaveMaster 804Zi-B
Oscilloscope
Up to 20 GHz bandwidth and 80 GS/s sample rate.The most advanced oscilloscope user interface.The industry’s only true hardware 14.1 Gb/s serial trigger.Low Jitter Measurement Floor and exceptional timebase stability.Comprehensive set of serial data analysis, debug, validation and compliance tools.Integrated 50 Ω and 1 MΩ inputs for true connection and probing flexibility.Integrated standard and custom measurements and math functions for unrivaled analysis capability.Multi-lane serial data eye, jitter and crosstalk analysis.Real-time de-embedding, emulation, and equalization.
-
Product
2 Channels, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTB
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
20 GHz Differential Probe with ProLink Interface
DH20-PL
Interface
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Channeling Decoder, Nav/Comm/Control Head
RCD200
-
Designed to provide the Avionics shop a simple and expeditious method for testing general aviation radio tuning. Provided are front panel mounted LED's as well as a digital display to provide the quickest code recognition while testing. With this simple method of testing you will soon find yourself testing all your radios and finding those troublesome intermittents. This unit also decodes altitude and ARC 1000 serial data. Click on picture for larger view.
-
Product
Serial I/O Boards
-
Serial Mode Protocols include Asynchronous, Bisync, SDLC, HDLC, IEEE 802.3, Synchronous Telemetry, Simple Clock/Data ("-SYNC" product line), Di-phase and SPI Interface. Transceiver support RS485, RS422 (V.10), RS232 (V.28), RS423, V.35, RS530, as well as other software selectable mixed protocol modes Up to Eight Independent Serial Channels per Board Synchronous Serial Data Rates up to 10 Mbits/sec Asynchronous Serial Data Rates up to 1 Mbits/sec PMC and cPCI rear I/O support Custom Protocols Available
-
Product
Altitude Data Simulator
ADS-100
-
The Model ADS-100 is an all solid-state device that simulates the output of altitude encoders/digitizers in both parallel and serial (RS232) data formats. Designed to substitute for an altitude encoder when testing and troubleshooting an aircraft's altitude reporting system, the ADS-100 provides two RS-232 compliant outputs in addition to the ICAO pressure altitude code.
-
Product
Android Software
SonarMite 'Plus' App
-
The SonarMite+ App is based on the free SonarMite App but offering additional features. The software is an Android App designed to work with the popular SonarMite Bluetooth Echo Sounder used in hydrographic surveying applications. With the demise of Hyperterminal as a standard terminal application the end user is left with little choice for a simple communications program with serial data devices. Connecting via Bluetooth is cleaner than USB cable, there are no wires and the connection is independent of baud rate and other serial port settings. Most terminal programs are not easily configured with commands to directly interface with instruments such as SonarMite.
-
Product
Data Analyzer, 8 GHz Bandwidth, 4 Input Channels, 32 GS/s Max Sample Rate
SDA 808Zi-B
Analyzer
8 GHz, 32 GS/s, 4ch, 32 Mpts/Ch Serial Data Analyzer with 15.3" WXGA Color Display.
-
Product
PCI Express® 5.0 Interposer
OCP NIC 3.0
Interposer
The Summit product family includes a wide variety of Interposer systems, designed to reliably capture serial data traffic while minimizing perturbations in the serial data stream. Probes include interposers, which are designed to capture data traffic crossing the PCI Express card connector interface, and MidBus probes, which are designed to capture traffic flowing within a PCB.
-
Product
PC COM Port Adapters
-
These adapters allow PCs with one or more standard serial COM ports to monitor serial data. For adapters for PCs with only USB ports.
-
Product
PXI 36 Channel Data Comms MUX, 96-pin SCSI
40-735-912
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. This 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
PC based Serial Data Analyser
FSA32
-
This PC application is a tool to monitor and display asynchronous serial data. It can also transmit messages and monitor and set control lines. It has comprehensive triggering facilities, and runs on Windows 95 or later.
-
Product
PXI Dual 18 Channel MUX, 96-Pin SCSI Connector
40-735-912-S1
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
Datum Universal Interface
DUI
-
Datum Electronics specifically designed the Universal Torque Sensor Interface which accepts serial data, displaying the output data and a wide range of additional analogue and digital outputs, s 4-20mA, +/-5Vdc, 0-5Vdc, +/-10Vdc, 0-10Vdc as well as RS232/485 serial data.The Datum Universal Interface (DUI) interfaces with all our rotary, static, reaction, digital torque sensors and torque transducers, as well as shaft power measurement solutions.
-
Product
RS232 / RS485 / RS422 / TTL Serial Repeaters & Hubs
-
CommFront offers a range of rugged, industrial-grade RS232 / RS485 / RS422 / TTL repeaters and hubs to meet serial communications' data distance needs by converting unbalanced signals to balanced ones, deploying repeaters to boost signal strength, and implementing hubs for star-configured connections, while still taking full advantage of cost-effective and readily-available copper wire.
-
Product
DH Series QuickLink Adapter, 8 GHz BW
DH-QL
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
PMC Compatible Bi-Directional Serial Data Interface
PMC-BiSerial III
-
The PMC BiSerial family has been updated to include a Spartan III [Xilinx] based card with expanded capabilities.. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PMC-BiSerial-III. The BiSerial III features completely isolated FIFOs with 32 bit ports for increased adaptability and performance.
-
Product
WaveMaster Oscilloscope, 6 GHz Bandwidth, 4 Input Channels, 40 GS/s Max Sample Rate
WaveMaster 806Zi-B
Oscilloscope
Up to 20 GHz bandwidth and 80 GS/s sample rate.The most advanced oscilloscope user interface.The industry’s only true hardware 14.1 Gb/s serial trigger.Low Jitter Measurement Floor and exceptional timebase stability.Comprehensive set of serial data analysis, debug, validation and compliance tools.Integrated 50 Ω and 1 MΩ inputs for true connection and probing flexibility.Integrated standard and custom measurements and math functions for unrivaled analysis capability.Multi-lane serial data eye, jitter and crosstalk analysis.Real-time de-embedding, emulation, and equalization.
-
Product
Quad Serial FPDP Interface with Virtex-6 FPGA - PCIe
Model 78611
-
Model 78611 is a member of the Cobalt® family of high performance PCIe boards based on the Xilinx Virtex-6 FPGA. A multichannel, gigabit serial interface, it is idealfor interfacing to Serial FPDP data converter boards or as a chassis-to-chassis data link. The 78611 is fully compatible with the VITA 17.1 Serial FPDP specification. Its built-in data transfer features make it a complete turnkey solution. For users who require application-specific functions, the 78611 serves as a flexible platform for developing and deploying custom FPGAprocessing IP
-
Product
Interposers and Probes
-
The Summit product family includes a wide variety of Interposer systems, designed to reliably capture serial data traffic while minimizing perturbations in the serial data stream. Probes include interposers, which are designed to capture data traffic crossing the PCI Express card connector interface, and MidBus probes, which are designed to capture traffic flowing within a PCB.
-
Product
Small Form Factor Recorder
Talon RTR 255x series
-
The Talon RTR 255x series implements Pentek's extensive line of digital serial modules including 40Gb Ethernet, serial Front Panel Data Port (sFPDP) and LVDS. All are capable of both receiving and transmitting data for recording and playback of data streams. The digital serial interfaces provide popular options for remote connection of the recorder to data sources. RTR 2555 - Ethernet: 1-, 10-, and 40-Gigabit Ethernet supporting both TCP and UDP protocols, with copper or optical interfaces.
-
Product
Dataloggers
-
Data loggers with one or more signal channels for DC and AC voltages and currents, thermocouples, Pt thermometers, process signals and serial data interfaces RS232 / RS485 are designed for industrial use. They can also be used as monitors or process controllers with additional data and signal outputs for control purposes. The devices are designed for panel construction and have communication software for Windows applications.
