Debug
See Also: Debuggers
-
Product
Simulator for Test Driving of Drones & Robots
Aerial Informatics & Robotics Platform
-
The Aerial Informatics and Robotics platform solves for these two problems: the large data needs for training, and the ability to debug in a simulator. It will provide realistic simulation tools for designers and developers to seamlessly generate the copious amounts of training data they need. In addition, the platform leverages recent advances in physics and perception computation to create accurate, real-world simulations. Together, this realism, based on efficiently generated ground truth data, enables the study and execution of complex missions that might be time-consuming and/or risky in the real-world. For example, collisions in a simulator cost virtually nothing, yet provide actionable information for improving the design.
-
Product
On-Chip Debugging Emulator
E2 Emulator
-
The new E2 emulator is an advanced on-chip debugging emulator and flash programmer developed based on a concept of "improvement of development efficiency". The download speed is up to twice as fast as the E1 emulator. Moreover, new solutions contributing to reduction in development time will be available.
-
Product
Resistive & Capacitive AC Load Bank
RCD
-
RCD AC load banks are used to test the REAL working condition of UPS, rectifier, inverter and etc who are loaded by non-linear or electronic load with non-constant resistance such as computer, networking equipments and etc. Through the accurate detection of its output and power quality, users could avoid the inadequate loading capacity or cause pollution to power grid, so as to guarantee supply security. JUNXY RCD load banks leading power factor loads are created to debug power supply system parameters such as its crest factor test.
-
Product
LabVIEW Professional Development System
-
ntegrate hardware from a variety of measurement instruments and devicesIntuitive graphical programming syntax to simplify automationBuild custom user interfaces for engineering applicationsBuilt-in algorithms for signal processing, analysis, math, and PID controlSoftware engineering tools to debug, validate, and deploy codeOne-year SSP membership for technical support, online training, and software upgrades
-
Product
A Serial Data Link Monitor for Windows
Listen
-
Listen is a Data Link monitor designed to assist debugging & troubleshooting serial communications links. Listen utilizes standard Windows COM port drivers to tap into RS-232 transmit signals for monitoring bi-directional communications between two devices.
-
Product
PXI & LXI Simulation Tools
-
Would you like to do code development with minimal hardware or see real-time switching and debug information? The LXI Simulation Tool can do that for you. This tool supports the simulation of all our PXI and LXI switching products, and most of the PXI simulation products in one highly portable package. The tool provides you with a simple and highly portable platform for application development.
-
Product
CPCI Test Extender 6Ux400mm
117EXT6116-0XXX
-
The cPCI extender boards are designed to bring a circuit card completely out of a card cage or enclosure so that it can be tested or debugged on each 2mm HM connector in P1-P5. Each line in rows A-E can be isolated with the DIP switches.
-
Product
SPICE circuits & model Debugger / Analyzer
SpiceVision PRO
-
SpiceVision PRO takes the complex SPICE descriptions produced by many EDA tools and generates clean, easy-to-read transistorlevel schematics and circuit fragments, and design documentation to speed up debugging and project development.
-
Product
Logic Analyzer Probes
FS2354 & FS2355
-
The FS2354 and FS2355 are logic analyzer probes used to test DDR3 SO-DIMM memory modules. When used with the triggering and analysis capabilities of Keysight’s Logic Analyzer modules, it gives the user an extremely effective tool for debugging, testing and verifying DDR3 SO-DIMM systems.
-
Product
Evaluation Board
emPower
-
SEGGER Microcontroller GmbH & Co. KG
The emPower eval board provides a comprehensive set of SEGGER's middleware products, accelerating the start of any embedded project. SEGGER's embOS real-time operating system is at the heart of the evaluation. Furthermore, evaluation versions of the file system emFile, graphics library emWin, emUSB Host & Device, and TCP/IP stack embOS/IP (including web server demo) enable full use of the available emPower peripherals. emPower also features a J-Link OB, an on-board version of SEGGER's market-leading debug probe J-Link, which includes drag & drop programming and COM-Port support. There are three expansion interfaces to easily connect additional modules. Each connector provides I2C, SPI, UART, GPIO/timer, analog input and power. A display adapter connector enables the connection of small TFT displays. The emPower board is powered by USB only. Current consumption drawn strongly depends on the application and connected peripherals. Idle consumption is approx. 85 mA.
-
Product
Text-Based Way to Connect & Disconnect Relays on ABex Modules
ABex Switching
-
The ABex Switching features a text-based way to connect and disconnect relays on ABex modules. Alias names for channels could be defined in a DUT specific topology file and then be used for text-based switching. These alias names are also shown in the Konrad System Manager allowing easy debugging of test sequences. The ABex Switching functionality could be either used out of NI Teststand with the provided test steps or via API from other programming languages.- Text-based switch routes- XML based topology for Alias mapping- Switch routes with support for Alias names- Seamless integration into Konrad System Manager
-
Product
USB Type-C Interconnects Compliance Test Software
S94USBCB
-
Use the S94USBCB software to test, debug and characterize your USB Type-C cable and connector designs. The PathWave TAP based test sequencer automates the network analyzer (VNA) for each test and generates a comprehensive HTML report. When run with L8990M switch matrix, it enables 20-ports fully automated test without port re-connection.
-
Product
DIMM Interposer Probe
FS2361
-
The FS2361 is a logic analyzer probe used to test DDR3 DIMM memory. When used with the triggering and analysis capabilities of Keysight’s U4154/64 Logic Analyzer modules, it gives the user an extremely effective tool for debugging, testing and verifying DDR3 DIMMs.
-
Product
MIPI M-PHY V5.0 Receiver Test Software (Frame Generator)
N5991MM5E
-
Generate MIPI M-PHY 5.0 sequences and signaling at HS-GEAR5 and lower speeds, for debugging, troubleshooting, and conformance test purposes, using the N5991MM5E Frame Generator software, for the M8040A BERT platform.
-
Product
Universal, Production In-System Programmer
FlashRunner Series
-
FlashRunner is a universal, production In-System Programmer.It is the result of many years of experience in developing programmingand debugging solutions for microcontrollers.
-
Product
RF Test Spectrum Measurements over CPRI
Integris 3000
-
Most modern cell tower network configurations place the Remote Radio Head (RRH) at the top of the tower and the baseband unit(BBU) at the bottom of the tower. While this configuration is advantageous for both computational efficiency and mitigation of RF loss across the cable, it means the only place along RF can be accessed is at the top of the tower. This forces field technicians to have to climb the tower to measure and debug RF noise problems.
-
Product
PCI To PC104 Extender Board
MS 1717
-
PCI to PC104/EPIC Extender card is used for extending the standard desktop PCI bus to compatible PC104 or EPIC bus. This will help to test all the PC104 cards through standard PC without any embedded processors. This card is very low cost board and very use to interface with standard board. This board also facilitates to debug the PC104 or EPIC boards.
-
Product
DH Series Tip - CrossSync PHY PCIe5 CEM x16
DH-CSPHY-PCIE5-CEMX16
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Embedded Analysis Software for the 2000 X-Series
D2000GENB
-
Test and debug I²C, SPI, RS232/422/485/UART designs with triggering, decoding, and pass / fail mask limit testing.
-
Product
USB-8486, USB, 1-Port, Fieldbus Interface Device
781160-02
-
The USB‑8486 is a FOUNDATION fieldbus device for developing applications with the NI‑FBUS driver, NI‑FBUS Configurator, and NI‑FBUS Monitor. FOUNDATION fieldbus is a popular industrial communication standard for process control applications. The NI‑FBUS Configurator features user-friendly multi-window interfaces to provide tools for the complete configuration, programming, and execution schedules of FOUNDATION fieldbus segments. The NI‑FBUS Monitor is a stand-alone application used to monitor, debug, and analyze fieldbus data packets.
-
Product
cRIO-9043, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 4-Slot CompactRIO Controller
785620-02
-
1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 4-Slot CompactRIO Controller - The cRIO-9043 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 160T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
In-Circuit Debugger for Power Architecture 55xx/56xx (Nexus)
ICDPPCNEXUS
-
P&E's ICDPPCNEXUS for Windows is a powerful tool for debugging code on a Freescale MPC55xx/56xx processor. The debugger comes with P&E's PROGPPCNEXUS flash programmer.
-
Product
Protocol Analyzer
RapidIO
-
Sanifferr' s RapidIO architecture incorporates its protocol analyzer and traffic generator into the same hardware, making it an elegant and complete solution for debugging devices within a Serial RapidIO environment.
-
Product
Logic Analyzer
GoLogicXL-36
-
Logic analyzers and oscilloscopes offering fast sample rates and large memory depths are required to debug and test modern electronics. The GoLogicXL captures a very large window of bus activity using sample depths up to 1 billion samples. 4 GHz sampling rates expose the finest details in your signals. 1 GHz Transitional sampling provides the optimum method to capture fast data bursts separated by seconds, minutes, or even hours of bus inactivity. The GoLogicXL State analysis can also synchronize with single-data-rate 300 MHz SDR clocks, and double-date-rate 250 MHz DDR clocks (500 MHz effective).
-
Product
Debug Adapters
-
One thing is sure in the life of an embedded developer - your next microcontroller development board will be fitted with a different debug connector to the one used in your previous design.
-
Product
NetFlow Tester
-
NetFlow Tester simply dumps the data of all NetFlow packets that a computer receives from a Cisco router –useful when debugging bandwidth monitoring configurations based on the NetFlow protocol.Available for NetFlow v5, v9, and IPFIX.
-
Product
Azure Functions
-
Develop more efficiently with Functions, an event-driven serverless compute platform that can also solve complex orchestration problems. Build and debug locally without additional setup, deploy and operate at scale in the cloud, and integrate services using triggers and bindings.
-
Product
Test & Programming Software
ScanExpress
-
The ScanExpress Family of boundary-scan software offers a fully integrated development environment that includes boundary-scan and at-speed functional test program generation, test program execution with advanced pin level diagnostics, interactive boundary-scan debugging, and in-System Programming (ISP) of devices such as Flash memory, serial EEPROMs, CPLDd, and FPGAs.
-
Product
PC Analyzer / Debugger
RapidDriver Explorer
-
RapidDriver Explorer is an intelligent tool for PC hardware analysis and debugging. RapidDriver Explorer allows you to start working with your hardware device with just a few clicks of the mouse. Simply install your new hardware, create a new RapidDriver project, and then select your device from the list of PnP devices auto-detected by RapidDriver.
-
Product
PCI Smart Bus Extenders
PCIEXT-64U - Live Insertion PCI Bus Extender
-
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment.
