CCD
Devices for recording images, typically consisting of an integrated circuit (IC) with an array of coupled capacitors.
-
-
-
Product
OEM CCD Camera
Syncerity BI-NIR Camera
-
The TE-cooled back illuminated 2048 x 70 CCD Camera combines affordability, performance and versatility for OEM applications. With peak QE of 84% @ 700nm and 20% at 1050nm, Syncerity BI-NIR offers a relatively broad response and addresses multiple applications. In the near-NIR, this detector is a much lower cost alternative to a deep depleted CCD, with no etaloning. Syncerity’s flexible design allows our OEM-dedicated team to quickly adapt the camera for industrial requirements, ranging from alternate CCD chips to electronics
-
Product
CCD Foundry Services
-
Teledyne DALSA Semiconductor’s 150mm CCD process offers surface or buried channel operation at up to 15V with two or three layers of polysilicon and one, two or three layers of metal. A modular processing approach allows our foundry customers to adjust process parameters to meet the most demanding requirements for CTE (>99.999%), charge storage capacity, and dark current (<1nA/cm2). The base process uses 1X projection lithography with 2.5µm design rules, allowing die sizes of up to 100mm X 100mm. Where required, tighter alignment tolerances and smaller feature sizes can be obtained by using 5X lithography, using a mix and match or all-stepper approach. The maximum die size attainable with the stepper is 22mm X 22mm, but larger sensors can be fabricated using stitching.
-
Product
Underwater Color Zoom CCD Camera
Surveyor-SD
-
The Teledyne Bowtech SURVEYOR-SD underwater colour zoom camera utilises CCD technology, delivering exceptional picture quality, with a 28:1 optical zoom lens and a horizontal resolution of 670 TV lines, all within a 4,000 (or 6,000) metre rated high quality titanium housing, with a 99.7% optically clear sapphire window.
-
Product
CCD Device Handlers
-
Exatron has been in a unique position to supply handling systems for the new CCD device market. Manufacturers of CCD devices came to Exatron when these devices were new, looking for custom handling applications, and Exatron responded by modifying its Model 3000B, 3000BL, 5000, 5080, and 8000 systems to accommodate CCD devices.
-
Product
Taper System, CCD Beam Imaging Camera
TaperCamD series
-
355 to 1150 nm, standard CCD detectorHyperCal Dynamic Noise and Baseline Correction software (Pat. Pending)CTE Comet Tail Elimination for > 900 nm (Pat. Pending)Port-powered USB 2.0; flexible 3 m cable, no power brick14-bit ADC, 4 MB image buffer & on-board microprocessorWindow-free sensors standard for no fringing25,000:1 electronic auto-shutter, 40 s to 1000 ms1,000:1 SNR (30/60 dB Optical/Electrical)
-
Product
Low Light Level High Res Monochrome Underwater CCD Camera
Explorer-Pro
-
The Teledyne Bowtech Explorer-Pro low light level, high resolution monochrome underwater CCD camera, is the ideal solution for extremely low light level, underwater viewing and navigation, yet still producing excellent images in high intensity illumination.
-
Product
Testing for Si Solar Cells Using High Performance CCD
EL Imaging Tester
-
EL Testing for Si Solar Cells using High Performance CCD. The determination of luminescence (photo emissions) in solar cells is an important characterization tool. Typical solar cells often have defects which limit the efficiency or lifetime of a cell. Many of these defects are visualized with Luminescence Imaging. By using this technique, the manufacturing process can be optimized to produce better cells. Luminescence Imaging takes advantage of the radiative inter-band recombination of excited charge carriers in solar cells. The emitted photons can be captured with a sensitive CCD camera to obtain an image of the distribution of the radiative recombination in the cell. This distribution is determined by the local excitation level, allowing the detection of electrical losses, thus mapping the diffusion length of minority carriers as the emitted light is low intensity and in the near infra-red range, the CCD camera has a high sensitivity wavelength from 900 to 1100 nm with little thermal noise. This CCD camera provides excellent resolution of 1024 x 1024 pixels with a large 1μm pixel size, multi-megahertz readout speed, and robust USB 2.0 connectivity. The EL CCD Camera is the ultimate high-performance CCD camera for electroluminescence and photoluminescence imaging for Photovoltaic (PV) Cells and Modules. This camera combines low noise electronics and optimal sensitivity in NIR.
-
Product
Chrysler CCD Vehicle Bus Comms PC Card
SL100
-
The SL100 uses a standard 16450 UART with baud rate settings that makes it capable of communicating with a Chrysler CCD Vehicle bus. The SL100 uses a protected interface driver chip, as prescribed by the bus specification, to connect with vehicle peripherals in a robust and highly noise immune way. The card automatically configures to become another COM port by using the built-in O.S. drivers that are tried and tested and are optimized to work in the Windows environment.
-
-
Product
USB 3.0 Cameras With CCD
xiD
-
*Quality components - Sony "EXview HAD CCD II" sensors delivering 2.8, 6.1, 9.1 and 12 Mpix*Fastest - Highest speed using full 4 TAP readout potential*Industry standard interface - Compliant with USB 3.0 SuperSpeed specification*Versatile mini camera - Subtle 60 x 60 x 39 mm, 320 grams (1)*Power - Lowest power consumption starting at 3 Watt, bus powered with USB3 cable*Cool - Minimal heat dissipation with passive COOLing*Compatibility - USB 3.0 support for Windows 7 and 10, macOS, Linux, ARM and 30 Libraries*Connectivity and Synchronization - Programmable opto-isolated input and output, 3 status LEDs*Bandwidth potential - 5Gb/s interface 400Mpix/s data throughput*Software interfaces - GenICam / GenTL and highly optimized xiAPI SDK for Image Processing*High grade - Quality class of sensors is combined with specially selected IR filters *Easy deployment - Range of accessories and widest hardware and software interoperability*Highly Customizable - Available in Board level and with Peltier TE Cooling
-
-
Product
CCD and Imaging Front Ends
-
Analog Devices is the premier supplier of high performance analog front-end devices in CCD/CIS imaging and time-of-flight applications. Many leading manufacturers of security cameras, machine vision cameras, high-resolution scanners, and other imaging systems depend on ADI’s products to deliver the highest performance with the lowest power dissipation in the market.
-
Product
Portable CCD Spectroradiometer
LMS-6000
-
The Portable CCD Colorimeter Spectroradiometer has the following versions which can measure different parameters: • LMS-6000: illuminance (lux), E(Fc), Ee(W/m2), Tc (K), Duv Correlated Color Temperature (CCT), Chromaticity Coordinates, CRI, Purity, Peak Wavelength, Dominant Wavelength, Half Bandwidth, Center Wavelength, Centroid Wavelength, Total Color Difference, Brightness Difference, Red-Green Degree, Yellow-Blue Degree, CCT Difference, SDCM Diagram, Spectrum Diagram • LMS-6000L: cd/m2, fL, Tc (K), Duv Correlated Color Temperature (CCT), Chromaticity Coordinates, CRI, Purity, Peak Wavelength, Dominant Wavelength, Half Bandwidth, Center Wavelength, Centroid Wavelength, Total Color Difference, Brightness Difference, Red-Green Degree, Yellow-Blue Degree, CCT Difference, SDCM Diagram, Spectrum Diagram • LMS-6000P: LMS-6000 Parameters+PAR, PPFD, YPFD, Blue-purple irradiance Eb, Yellow-green irradiance Ey, Red-orange irradiance Er, Ratio of red and blue radiation Erb_Ratio • LMS-6000S: LMS-6000 Parameters+PAR, PPFD, YPFD, Blue-purple irradiance Eb, Yellow-green irradiance Ey, Red-orange irradiance Er, Ratio of red and blue radiation Erb_Ratio, Rf and Rg according to TM-30 • LMS-6000F: LMS-6000 Parameters+Flicker test • LMS-6000B: LMS-6000 Parameters+Blue Light Hazard Weighted Irradiance according to GB/T20145, CIE S009/E:2002 • LMS-6000BF: LMS-6000 Parameters+Flicker test, Blue Light Hazard Weighted Irradiance according to GB/T20145, CIE S009/E:2002
-
Product
Miniature High Resolution Underwater Color CCD Camera
L3C/LCC-720-L
-
The Teledyne Bowtech L3C/LCC-720-L miniature high resolution underwater colour CCD camera (with six integral high intensity LEDs) provides a low cost solution to general underwater viewing and observation, down to 1,000, 4,000 or 6,000 metres in confined spaces.
-
Product
CMOS Cameras
-
A digital still or video camera that uses a CMOS-based image sensor chip rather than a CCD to record the picture.
-
Product
Light Analysis
-
Welcome to Thorlabs; below you will find links to detectors and instrumentation that measure the various properties of light, a subset of our entire line of photonics products. Thorlabs offers an extensive selection of instruments that measure the properties of light. Our versatile power and energy meters can be used with over 25 different sensors in order to make NIST-traceable power and energy measurements. If the convenience of a meter is not desired, our selection of detectors includes basic photodiodes (uncalibrated and calibrated), photodetectors (biased, amplified, and avalanche), CCD and CMOS arrays, position detectors, integrating spheres, and photomultiplier tubes. The Beam Characterization category contains beam profilers (camera and scanning slit), a wavefront sensor, spectrometers, and interferometers, while the Polarimetery link leads to a selection of instruments used to measure and control the polarization of light.
-
Product
Microscope Cameras
-
In contrast to digital cameras for normal photography, microscope cameras are built to meet the demands of high-end science- and research applications. For maximum light sensitivity they use large CCD or CMOS sensors for image acquisition. Color reproduction is often critical, why features like Microscanning or Color-Co-Site Sampling ensure optimal image quality. Due to the lack of a light absorbing color filter monochrome microscope cameras for fluorescence imaging are even more sensitive.
-
Product
CCD Camera
MicroPublisher 6
-
The MicroPublisher 6 CCD camera is a great solution for high resolution color microscopy imaging. This 6 megapixel camera delivers high quality color images with a large field of view and accurate color representation. Connects easily through high speed USB 3.0.
-
Product
Imaging Spectrograph
CP140
-
The CP-140 Imaging Spectrograph offers the OEM customer a sturdy, low-cost, f/2, modular instrument, with unsurpassed spatial resolution. High-efficiency, ion-etched, holographic gratings make the CP-140 the perfect spectrograph for use with multiple fiber inputs, linear arrays, and CCD type detectors. Selected gratings cover specific spectral regions from 190 nm to 2500 nm.
-
Product
Multichannel Grating Spectrometer
PoliSpectra® Quad
-
Horiba’s OEM Polispectra Quad spectrometer is an integration of four VS70 spectrometers built around Horiba JY Type-IV flat-field aberration-corrected holographic concave gratings. This high throughput VIS spectrometer with 4 fiber inputs provides simultaneous acquisition of 4 channels at high speed with minimal crosstalk. The main electronics board is designed to read the two CCDs on the system simultaneously and provides 1-8X binning capability. This OEM system is a unique and innovative approach to drastically reduce the cost per channel.
-
Product
Spectrometers, Vacuum
-
A compact and versatile vacuum ultraviolet monochromator. A selection of aberration-corrected diffraction gratings is available so you can tailor the instrument to your wavelength of interest and application. Connect this instrument directly to your vacuum plasma physics experiment or build an intense UV tunable source. It is available as a scanning monochromator, as a spectrometer, or as a spectrograph with microchannel plate or direct-detection CCD. The Model 234/302 is popular in systems due to its compact design, high throughput and resolution. It is also available with an additional entrance or exit port.
-
Product
High Power LED Test System
Lumere-GM
-
Evolusys Technologies Sdn. Bhd.
Lumere GM is a LED test and measurement system for various parameters of LED light. It is a high-accuracy system with a temperature-controlled CCD, its geometry conforms with CIE-Publication 127, and the test program is easy to configure and adjust. The Lumere GM is used in laboratory applications and in the production of high-power LEDs.
-
Product
Machine Vision Cameras
Manta Series
-
High-performance industrial cameras with a large choice of sensors, modular options and built-in image optimization. VGA to 12 Megapixels. CCD and CMOS (Sony, CMOSIS). Up to 125 fps. NIR versions, board level option.
-
Product
Color Measurement With Line Scan Cameras
-
The Chromasens line scan cameras offer new approaches for the color-accurate capture of objects. The chromaPIXA has an internal FPGA-based color calculator which converts the color information of the CCD sensor on-the-fly into standard output color spaces. Algorithms are used which allow a more precise transformation than the usual 3x3 matrix transformation.
-
Product
CiCi-Raman-NIR Spectrometer
-
HORIBA Scientific is the world leader in Raman spectroscopy, with a long history in the technique. HORIBA OEM has pioneered Raman systems for spectroscopy, designing and manufacturing them for over four decades. We provide miniature spectrometers and systems for industrial applications such as process control, security, pharmaceutical, medical and semiconductor. The CiCi-Raman-785 is our high performance spectrometer featuring an aberration-corrected concave holographic grating configured with Horiba Scientific's Syncerity™ TE-cooled CCD camera with a VIS-NIR 2048 x 70 detector, in a TE-cooled Head at -50° C.
-
Product
Machine Vision Camera - 1.3 MP, 60 FPS, e2v EV76C560, Color
Flea3 USB3
-
The Flea®3 line of USB3 Vision, GigE Vision and FireWire cameras offers a variety of CMOS and CCD image sensors in a compact package. The Flea3 leverages a variety of Sony, ON Semi, and e2v sensors ranging from 0.3 MP to 5.0 MP and from 8 FPS to 120 FPS. For FLIR GigE and USB3 cameras with the latest sensors and most advanced feature sets, please refer to our Blackfly S and Oryx camera families.
-
Product
Line Scan Cameras
-
JAI’s extensive product offering includes color line scan cameras featuring prism technology with multiple CCD or CMOS linear sensors delivering high performance color/NIR imaging solutions for high-speed web/continuous applications such as print verification, tile inspection, food/fruit sorting, and more. Also monochrome line scan cameras with ultra fast scan rates.
-
Product
Low-Noise DC Bias
-
Imaging devices, such as CCDs, IR FPAs, and CMOS image sensors, require DC bias with very low electrical noise to prevent contamination of the image. Image quality can also be enhanced by carefully tuning each bias voltage to extract the maximum signal/noise ratio out of an array. Pulse Instruments has decades of experience providing DC bias supplies with the flexibility required tocharacterize and test a variety of devices while maintaining the noise immunity required for satellite and astronomy applications.
