Filter Results By:
Products
Applications
Manufacturers
Loopback Testers
-
product
Fiber Optic Loopback MTP
Anfkom International Co.,Limited
Anfkom can provide single mode and multimode MTP MPO fiber optic loopbacks. MTP/APC Singlemode loopbacks, and MTP/UPC Multimode loopbacks using high quality US Conec MTP connectors for the highest quality polish and lowest insertion loss. All fiber modes including 9/125, 50/125, 62.5/125. Our MPO MTP loopbacks in standard configurations such as for QSFP modules for a QSFP MTP loopback tester. Custom MPO MTP loopbacks are also available for any configuration. Call or e-mail us about custom MTP MPO loopbacks- we can make any custom configuration you need for your custom MTP loopback needs.
-
product
FMC Loopback Test Board
The FMC loopback tester board enables developers and assembly factories to test and characterize the FMC carrier board interfaces. The board features full differential loopbacks on all the FMC high pin count (HPC) connector interfaces including LA, HA, HB, DP and CLK. It also provides a 125MHz transceiver LVDS reference clocks on GBTCLK signals. The FMC loopback board is based on VITA 57 standard with ruggedized conduction or air cooling.
-
product
Up to 3.2GHz, DB9 Male Fibre Channel Loopback Tester
F9M-LPBK
This premium loopback tester support speed of up to 3.2GHz and certified to pass the eye-pattern test.
-
-
product
Fiber Optic Loopback Tester
N844-LOOP-12F
Tripp Lite N844-LOOP-12F MTP / MPO OM3 Fiber Optic Loopback Tester is typically used for test and measurement procedures in networking environments. The device is ideal for a multitude of applications that require signal looping in a MTP / MPO form factor. Features push-pull tab for easy disconnect. A dust cap is included for protection during storage.
-
product
Up to 3.2GHz, HSSDC 8Pin Male Fibre Channel Loopback Tester
F8M-LPBK
This premium loopback tester support speed of up to 3.2GHz and certified to pass the eye-pattern test. (Connector: HSSDC 8Pin Male).
-
product
Bit Error Rate Tester - MATRIQ
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
MTM-Bus Tester
PXIe-1149.5
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
product
KVS Rugged Igniter Tester With Current Monitor
4314
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
product
PAM4 Bit Error Rate Tester.
BERT-1102
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
product
Loopbacks
Loopbacck plugs are used for network diagnostics, system configuration testing, and device burn-in. Looping back the signal allows for testing of the optical network.
-
product
Fiber Optic Loopback MPO
Anfkom International Co.,Limited
Low insertion loss, high return lossMT based Multi-fiber Connector up to 12 fibersHigh credibility and stabilityGood in repeatability and exchangeabilityStandard: Telcordia GR-1435-CORE compliant
-
product
Automated Coherent Receiver Tester
CoRx Tester.
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
product
HD-TVI Tester, HD-CVI Tester, AHD Tester
M-IPC-300 series
Fuzhou Metricu Technology Co Ltd
4 inch IP camera tester
-
product
Torque Tester
TorqueLab® LTT-Series
The torque analyzer is designed for calibrating tools, joint testing, auditing and measuring torque. Torque tools go out of calibration with use. To maintain consistent accuracy, torque tools must be checked periodically for wear or defective parts. A power or hand torque tool is a measuring tool that must be properly calibrated and maintained.
-
product
Battery Testers
Battery testers are designed for the new measurement requirements of the battery industry. They are special for measurement use in low-resistance batteries, large-scale lithium battery packs and fast product sorting in production lines.
-
product
Environmental Testers
Axi'An Beicheng Electronics Co., LTD.
Environmental Testers by RuoShui: digital thermometers, thermal imaging analyzer, infrared thermal imager, thermo-hygrometer, nicety meters, rain gauge, coating thickness gauges, combustible gas detector and monitor, carbon monoxide monitor, digital anemometer, vibrometer meters, storboscope tachometers, digital tachometer, combustible gas detectors, 4 in 1 gas detector, digital refractometer, wood moisture meter, lux meter, sound level meter, sound meter, and more.
-
product
Tester For Maintenance
Mobile wiring testers in Multibox design or in customer specific housing for maintenance on military vehicles.
-
product
Continuiy Tester
TE6-0713
Hangzhou Tonny Electric & Tools Co., Ltd.
Designed to test circuits while power is on, Use on 6V,12V and 24V applications
-
product
Pitot-Static Tester
PS-500
The PS-500 Pitot-Static tester is a low-maintenance digital tester that is fully portable.
-
product
Hipot Testers
We've been manufacturing hipot testers for over 75 years & have supplied many of the worlds leading manufacturers instruments with features that satisfy every type of requirement
-
product
Stater/Field Tester
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
• Touch Screen Interface• Windows® 10 Pro• High Reliability with Proven Design• USB Interface – No I/O boards in Computer• Remote Control Software for Factory Diagnostics/Updates• Full Network Compatibility
-
product
Installation Tester
M74
M74 measures Overall earth resistance, tripping time of RCDs type AC, Insulation and Continuity of earth and equipotential conductors according to the laws in force in private electric installations.
-
product
Cable Testers
CableJoG 256
The CableJoG 256 can test up to 256 individual connections of all manufacturers of connectors. This simple test instrument stores up to 12 separate connection configurations. Each cable that is tested is compared with the configuration stored in its memory to produce a pass/fail indication of each pin connection
-
product
Ultra-Compact Testers
adaptronic wiring testers of the ultra-compact class are available as low voltage testers and also as high voltage testers, as KT version with display and keyboard and as NT version with the grafical user interface NT Control.
-
product
Multifunctional testers
MI 3155 EurotestXD
MI 3155 EurotestXD is the newest flagship of Metrel’s most advanced line of multi-functional measuring instruments and is designed specifically for testing in industry. What differentiates this instrument from the rest is its ergonomic design and an intuitive user interface, encompassing a memory organizer and fully programmable AUTO SEQUENCEs, managed through a large colour touch screen display.
-
product
Motor/Generator Testers
Appliance motors are always evolving and the final testing of those motors gets more complicated every year. We build fully automated testers for domestic or offshore manufacturing facilities that can perform any amount of motor testing that you require with limited interaction by the operator.
-
product
CDM Tester
Tokyo Electronics Trading Co., Ltd.
Determine what level of CDM discharge causes device damage by placing the device package on a metal plate with the pins facing up.
