Product

Tire Rolling Resistance Test System

-

Ono Sokki

Ono Sokki

This system measures the rolling resistance of each tire accurately. In addition to the simultaneous measurement of tire loss resistance and rolling resistance coefficient for each drive by mode operation (JC08, WLTC), coasting test, constant acceleration/deceleration test and transient mode test are able to be performed. Furthermore, measurement of driving noise/ vibration of the tire, effect of the tire loss due to the temperature change can be verified by adding options.Conforming the JIS D 4234: 2009 and ISO 28580: 2009.

Product

Contact Resistance Tester

-

Weshine Electric Manufacturing Co., Ltd

Weshine Electric Manufacturing Co., Ltd

The loop resistance tester is used to test the conductive loop resistance of various switchgear, and the test current shall not be less than 100A. Due to the oxidation of the contact surface, poor contact tightening and other reasons, the contact resistance increases. When a large current flows, the temperature of the contact point increases, which further accelerates the oxidation of the contact surface and further increases the contact resistance.

Product

Water Cooled Active Resistance DC Electronic Load

WRx Series

-

Magna-Power Electronics, Inc.

WRx Series - Magna-Power Electronics, Inc.

Utilizing Magna-Power’s new patent pending Active Resistance Technology in combination with the company’s internally manufactured microchannel water-cooled heatsinks, the WRx Series addresses high power DC applications where exhaust heat control is essential. The WRx Series greatly increases power density compared air-cooled alternatives. An integrated solenoid controls the flow of water to avoid condensation. Full power can be achieved using conventional water, with water inlet temperatures up to 25 °C.

Product

Three-Phase Transformer Winding Resistance Meters

TWA Advanced Series

-

IBEKO Power AB

TWA Advanced Series - IBEKO Power AB

TWA Advanced series is the latest DV Power solution for three-phase transformer winding resistance measurement and tap changer analysis. They are capable of testing six transformer windings with a single cable connection, as well as three-phase automatic transformer demagnetization. It has the option of the automated test mode, where the instrument operates the tap changer without operator input (minimizing the risk of human error) and records winding resistance results based on pre-selected stabilization criteria.The unique DVtest method of tap changer analysis enables checking the moving contacts of on-load tap changers during the transition, measuring the transition time, detecting open circuits, and many other types of faults. It is performed with 0.1 ms sampling rate, together with the measurement of tap changer motor current which detects motor and mechanical issues. A special proprietary algorithm is used for testing tap changers connected through a built-in series (booster) transformer. The DVtest can be performed either on one phase or simultaneously on three phases. It can also be performed together with the winding resistance test in all tap positions.A unique advantage of TWA Advanced instruments is the capability of simultaneously testing the winding resistance of all three phases of a three-phase transformer connected in a YN configuration. This can significantly speed up the testing– for example, it enables the operator to perform 33 measurements instead of 99 on a tap changer with 33 tap positions.TWA500 is equipped with a large 10.1” graphical touch-screen display, while TWA400 has a 7” graphical touch-screen display. Besides making the interface much more user-friendly compared to older winding ohmmeters, it also enables certain test options that were previously available only with DV-Win software. The most important among them are DVtest, tap changer motor current measurement, “Heat Run” test, test templates, and automatic test mode.

Product

Surface Resistance Meter

WL MIDGET

-

Walter G. Legge Company Inc.

WL MIDGET - Walter G. Legge Company Inc.

WL MIDGET Surface Resistance Meter is an ultra-wide range, battery operated, portable instrument for measuring Surface Resistivity and Resistance to Ground of virtually any flat surface conforming to ASTM D-257 standard method by using recommended parallel bar sensing probe. Gives simple, repeatable measurements of conductive, static dissipative, and insulative surfaces. Ranging is automatic due to the use of high-speed OP-AMP Integrated circuits being linear, with changeover points +1/2 decade on a logarithmic scale. Repeatability equals + 5%.

Product

Solvent Resistance Tester

NRJ-100

-

Shanghai Dean Electrical Co., Ltd

NRJ-100 - Shanghai Dean Electrical Co., Ltd

Executive standard: GB/T4074.4-2008/IEC60851-4; Inspection standard: JB/T4279.10-2008Used to detect the solvent resistance performance of enameled round wires and flat wires with nominal conductor diameter above 0.250mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Pencil push unit would automatically lay down pencil and move ahead, lift pencil and automatically return to initial position;Used in combination with JRK-60 solvent thermostatic controller;Automatic pencil sharper can sharpen pencil tip to be 60° symmetrical to its axis;

Product

Standard Voltage 37 Pin D-Type Connectors for Pickering

-

Pickering Interfaces Inc.

Pickering Interfaces Inc.

The connectors below are suitable to use with Pickering cards and modules that utilize a standard voltage 37-pin D-type connector.

Product

Frequency Standards

-

Precision Test Systems Ltd.

Precision Test Systems Ltd.

Precision Test manufacturers a complete range of frequency standards.  This includes rubidium and OXCO models either free running or controlled by an external reference (GPS, GLONASS, Galileo, 1pps, 5 MHz, 10 MHz, IRIG-B etc).  Output frequencies typically 1 MHz, 5 MHz, 10 MHz, 10.23 MHz, 13 MHz, 100 MHz or bespoke frequency.

Product

Transformer Winding Resistance Meters

TWA Advanced Series

-

Amperis sl

TWA Advanced Series - Amperis sl

The TWA advanced series instruments are designed for six-winding resistance measurement and simultaneous three phase on-load tap changer analysis of both the primary and the secondary transformer windings. This is performed with a one singlestep cable setup, with test currents of up to 40A. Each transformer configuration has a special measurement algorithm which is optimized for the fast stabilization of test results. The TWA instruments generate a true DC ripple-free current. Both the injection of the current and the discharge of energy from the magnetic circuit are automatically regulated.

Product

Concrete Bulk Resistivity

RCON

-

Giatec Scientific Inc.

RCON - Giatec Scientific Inc.

Giatec RCON™ is a non-destructive device for measuring the electrical resistivity of concrete specimens in the laboratory without any additional sample preparation requirements. This measurement can easily be made on the same concrete samples that are currently used for the compressive strength testing of concrete.

Product

Skid (Portable Skid Resistance Tester)

-

MRC ltd.

MRC ltd.

(also known as the British Pendulum Tester) is an essential tool for anyone with a duty to minimize the risk of accidents arising as a result of slippery roads and floor surfaces. This device is also used to investigate the cause of accidents after they have taken place.

Product

Battery Resistance Tester

FBR-6100NT

-

Fuzhou Fuguang Electronics Co., Ltd.

FBR-6100NT - Fuzhou Fuguang Electronics Co., Ltd.

FBR-6100NT Battery Resistance Tester is a new generation handheld battery tester of FUGUANG™, which can quickly,intuitively and conveniently judge the deterioration of batteries (lead-acid batteries, lithium iron phosphate batteries and nickel-cadmium batteries, etc.). It has the characteristics of high accuracy, repeat consistency and anti-interference. It is an ideal tool for rapid battery daily check.

Product

Non-Contact (Pulse-Voltage Excitation Method) Ultra-Low Sheet Resistance Measurement System

PVE-80

-

NAPSON Corp.

PVE-80 - NAPSON Corp.

*No damage measurement by non-contact Pulse-Voltage excitation method*Easy to measure & carry around, Removable stage plate*Easy operation and data processing by PC with Software*Measurement result can shown by 3 types of measurement unit (Sheet resistance[Ohm/Sq], Electric conductivity[S/cm], Electrical conduction[S])*Pulse-Voltage excitation method : Pat. No.5386394 Joint development with Chiba Univ.

Product

Resistance Meter

MT16-4L

-

Holding Informtest

MT16-4L - Holding Informtest

М-module МТ16-4Л is a mezzanine module (hereinafter referred to as a mezzanine), designed to measure the resistance of resistive sensors using a four-wire measurement circuit in sixteen channels (sixteen-channel digitizer). М-module МТ16-4Л is installed on the mezzanine carrier - module НМ-М and is connected to it via a local information highway. Up to four mezzanines of various types can be installed on the NM-M module. The NM-M module, together with the mezzanines installed on it, forms a VXI module of the C-1 size and is used to create information measuring VXI systems.

Product

Earth Resistance Meter

-

Scope T&M Pvt, Ltd.

Scope T&M Pvt, Ltd.

Earth Resistance Meter

Product

Contact Resistance Meter

CRM 100B+

-

Scope T&M Pvt, Ltd.

CRM 100B+ - Scope T&M Pvt, Ltd.

SCOPE introduces its next generation of hugely popular CRM series contact resistance meter, CRM100B+ in all new super light avatar, based on cutting edge ultra capacitor technology. CRM incorporates some state of the art hardware & smart software features making it a must have tool for testing & maintenance engineers.

Product

Multi-Test Resistivity Measurement System

-

Signatone Corp.

Signatone Corp.

Sheet resistance mapping of thin films with a collinear 4-point probe, Temperature co-efficient of resistance (TCR) of thin films with collinear 4-point probe, Precision temperature co-efficient of resistance (TCR) with 2-point Kelvin probes and precision surface temperature probe, resistor testing with 2-point Kelvin probes,Precision resistor testing with a Kelvin probe card, temperature co-efficient of resistance resistor test (TCR), and Standard TCR test of multiple resistors with Kelvin probes or a probe card.

Product

Earth Contact Resistance Tester

-

SCR ELEKTRONIKS PVT. LTD.

SCR ELEKTRONIKS PVT. LTD.

SCR ELEKTRONIKS have developed an equipment namely Earth Contact Resistance Tester to test the appliance. To ensure the safety of operator it is essential that the Earth path (connection) should offer minimum impedance to by pass short circuit Current to Earth. This is ensured by measuring Resistance of the Earth path by passing heavy Current say 25 A. The Earth Contact Resistance Tester essentially comprises of a Variable Current source with digital Ammeter to measure the Current supplied. The Voltage drop across the Earth path is measured with a digital Voltmeter. Optionally for a particular Current (25 A) the meter can be calibrated in terms of Resistance. A timer is provided to switch off the Current after the Set Time.

Product

Loop Resistance Measuring Device According to DIN EN 61557-3 (VDE 0413-3)

-

PeakTech Prüf- und Messtechnik GmbH

PeakTech Prüf- und Messtechnik GmbH

A loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.

Product

Electrical Resistance (ER) Monitoring

-

Metal Samples Company

Metal Samples Company

The electrical resistance (ER) technique is an "on-line" method of monitoring the rate of corrosion and the extent of total metal loss for any metallic equipment or structure. The ER technique measures the effects of both the electrochemical and the mechanical components of corrosion such as erosion or cavitation. It is the only on-line, instrumented technique applicable to virtually all types of corrosive environments.