-
product
For Machining Center
We offer the ATC Run-Out Detection System and the Wireless Bore Gauge. We will boost the realization of increased productivity with high precision measurement technology.
-
product
PXIe-6536, 32-Channel, 25 MHz, 100 MB/s PXI Digital I/O Module
779988-01
32-Channel, 25 MHz, 100 MB/s PXI Digital I/O Module—The PXIe‑6536 can continuously stream data over the PXI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
product
Changeover
LT 4448
The LT 4448 is a changeover unit that automatically switches the signal from the primary signal to the backup signal when problems are detected in the primary signal.Two systems of input signals (primary and backup) are connected to the LT 4448, and the LT 4448 detects errors in the amplitude of the primary input signal.A single LT 4448 provides 11 pairs of BNC and LTC channels. These channels can receive SDI, NTSC/PAL black burst, HD tri-level sync, AES/EBU digital audio, word-clock, and LTC signals.
-
product
Optical Spectrum Analyzer
ID OSA
This instrument is a versatile Optical Spectrum Analyzer (OSA) based on a coherent detection principle provides picometer class spectral resolution across the C-Band (1528.5 – 1567.5nm).
-
product
Humidity and Temperature
Humidity of Building Materials
The T660 is a professional hand-held instrument for fast, non-destructive determination of moisture content distributions in areas up to a depth of 4 cm from the surface. The T610 is a professional hand-held instrument for rapid non-destructive measurement of sub-surface moisture content.By means of microwave technology it is possible to detect distributions of moisture content at a depth of up to 300 mm.
-
product
Logger Version 2-D Electro-Magnetic Current Meter for Deep Ocean
INFINITY-Deep AEMD-USB
INFINITY-Deep is an autonomously deployable data logger for current speed measurements in the deep oceans. The currents in the deep oceans are very weak. It is too hard to accurately measure the deep water currents by some ADVs (Acoustic Doppler Velocimeters) that detect the Doppler-effect by scatter with the suspended particles in the water, because the concentration is very low. INFINITY-Deep measures 2-D current data through a magnetic field according to Faraday's law. Therefore, even if the suspended particles do not exist around the sensor, it can provide the accurate current data. The depth rating is 6,000m. Compared to INFINITY-EM, the instrument has a depth and a tilt sensors to monitor mooring status. Also, the battery capacity doubles for long-term current velocity measurements.
-
product
Optical Power Meter
Shenzhen Golight Technology Co.,Ltd
Optical power meter is built-in large-sensitive surface photodetector and high-precision photoelectric detection. Power testing range is up to 65dB. Also It has optional functions of analog output and trigger sync input. It is widely used in various optical signal measurement.
-
product
Non-Contact Voltage Detector
VOLTCHEK
The VOLTCHEK is a variable non-contact voltage detector, A proximity device which detects the presence of an alternating electric or electromagnetic field. It is used by industry professionals for live or dead voltage determination of outdoor overhead or underground at URD test points. Firstly as a proximity device to determine live or dead situations and then as a touch device to verify the source has physically reached the zero AC field. This is the only equipment capable of testing all voltage from AC 415V to 765kV from a distance, beyond arcing zone.
-
product
X5 Pipeline X-Ray Inspection
Designed to be integrated into the production line and available with product pipes in 2.5 and 3 ", the X5 pipeline is perfect for a wide range of pumped products such as poultry, meat, slurries and sauces. The system is capable of offering good detection levels on a wide range of contaminants including all metal, bone, glass, dense plastics.
-
product
SparkFun RedBot Sensor
Line Follower
The Line Follower sensor is an add-on for your RedBot that gives your robot the ability to detect lines or nearby objects. The sensor works by detecting reflected light coming from its own infrared LED. By measuring the amount of reflected infrared light, it can detect transitions from light to dark (lines) or even objects directly in front of it.
-
product
AI-Powered HD Traffic Sensor
TrafiCam AI
Designed to reliably detect and classify road users, the TrafiCam AI is an intelligent HD visible sensor for traffic monitoring in complex urban environments. Featuring a low-light HD visible camera and AI algorithms built on 25+ years of traffic detection, TrafiCam AI offers detailed vision and data collection for safer, more efficient cities. Capable of tracking multiple objects, the advanced edge-based AI effectively controls intersections and gathers detailed traffic data for better city planning decisions.
-
product
Transceivers
Macom Technology Solutions Holdings Inc.
At MACOM we offer monolithic and stereo Doppler transceivers for directional motion detection. Our transceivers are used in a variety of applications such as automatic door openers, ground speed recorders and police radars. MACOM’s transceivers are well suited for high volume applications where small size and reliability are required.
-
product
240V Socket Tester Check Plug
CP501
The most popular socket tester available - detects 28 fault conditions.
A quick and easy way to ensure that 13A sockets are correctly wired, indicated by 3 bright long life LEDs.
Wiring faults are indicated by one or more of the LEDs failing to illuminate, with the pattern of lit LEDs indicating the type of fault detected. This fail-safe system means that any LED not lit indicates a fault. The robust ABS housing has a sculpted shape for easy removal and there is a look up chart on the tester for quick fault diagnosis.
The plug induces less than 5mA of earth leakage, well below RCD trip thresholds.
-
product
Portable Optical Pickup
OP200x
Power Measurement Technologies Inc.
The OP200x is a versatile, lightweight, portable instrument designed to detect watt-hour meter disk rotation, light pulses, LCD segments and contact closure events.
-
product
OverHead Lines Contact Voltage & Low Voltage Indicator
LVD-415
Standard Electric Works Co., Ltd
● No batteries required.● Every circuit is doubled.● Buzzer indicates voltage detected.● Led indicates voltage detected.● Neon scale indicates voltage.● Dual HBC fuses.● High grade fiber glass probes.● Super polished fiber glass.● High strength connecting cord.● Heavy duty rated.● Replaceable tips.● Choice of tips available.● Lightweight.● Small storage space.● Strong strength reliefs.● Double poles non-polarized.● Suitable for 45 to 70 Hz networks.● Contact detector type.● Passive circuitry.● Fiber glass 1.6mm - CU 35um PCB.● Super bright neon lights and LEDs.● Ergonomically-designed.● EN 61010-031 CAT IV 500V.
-
product
Under Ground Cable Fault Locator
Widely used in electrical and power generation sector for testing underground cables in order to detect any fault.
-
product
Non Contact Voltage Indicator
PL107N
Contact-free audible and visual indication of AC voltages between 90 and 1000 V AC Clear, omnidirectional flashing LED Quick and accurate detection of cable breaks Detects microwave leakage Phase detection in sockets Press to test switch avoids nuisance buzzing and extends battery life Supplied complete with 1.5 V AAA batteries
-
product
PCI Multifunction I/O
626
6 versatile 24-bit counters for encoders/timers with interrupt generation Fail-safe Digital I/O E-stop Relay Battery backup of counters Four 14-bit D/A outputs, 20 Khz update rate Sixteen 16-bit differential A/D inputs, 15 kHz rate Watchdog timer may be used to reset PCI bus 48 bi-directional digital signals for solid state relay boards, 40 with edge detection and interrupts
-
product
sbRIO-9253, Non-Enclosed, 50 kS/s/ch, 24-Bit, 8-Channel C Series Current Input Module
787433-01
Non-Enclosed, 50 kS/s/ch, 24-Bit, 8-Channel C Series Current Input Module - The sbRIO-9253 is an 8-channel analog input module for CompactRIO Single-Board Controller that provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. This module includes diagnostic functionalities to ensure nominal system operations with open-channel detection, power supply detection, and configurable thresholds. You can view the status of each channel and the power supply with eight LEDs. The sbRIO-9253 also features programmable hardware filters for your applications, such as specific Butterworth and comb filters that you can use to reduce the noise in your system.
-
product
Gas Detectors
Shenzhen Graigar Technology Co.,Ltd.
A gas detector is a device that detects the presence of gases in an area, often as part of a safety system. This type of equipment is used to detect a gas leak and interface with a control system so a process can be automatically shut down.
-
product
High Definition LWIR Science-Grade Camera
FLIR X8580 SLS™
The FLIR X8580 SLS is a high-speed, high definition longwave IR camera designed for scientists and engineers who need to capture detailed imagery of fast events, perform custom radiometric measurements, or detect points of failure in composites, solar cells, and electronics. This thermal imaging camera combines 1280 × 1024 resolution from the SLS detector with high-speed frame rates to offer shorter snapshot speeds and wider temperature bands for crisp stop motion imagery of high-speed events. With a four-position motorized filter wheel and support for FLIR motorized focus lenses, the X8580 SLS will provide high quality recordings, save time, and mitigate frustration in dynamic acquisition environments.
-
product
Gamma Air Monitor
Quant Air
QuantAir is a solution for measuring radioactive contamination in the air, it provides high-performance detection capabilities with accurate in-field quantification.
-
product
Rebar Locator
Profoscope
The Profoscope is a versatile, fully-integrated rebar detector and cover meter with a unique real-time rebar visualization allowing the user to actually “SEE” the location of the rebar beneath the concrete surface to a maximum depth of 180 mm. This is coupled with rebar-proximity indicators and optical and acoustical locating aids. Rebar diameter can also be estimated within the specified testing range. The Profoscope combines these unique features in a compact, light device that allows the user to operate this rebar detector with one hand making the task of locating rebars a simple and efficient process. In addition, Proceq’s rebar detector convinces through its intuitive user interface making rebar detection easy.
-
product
Refrigerant Leak Detector
KM 310 / KM 312
Kusam Electrical Industries Limited
LED Tip Light. Mute Function. Low battery indication. LED power indicator. Sensor failure indicator (KM 312). Start-up melody (KM 312). USB power adaptor (KM 312). Rugged flexible probe. 3 adjustable sensitivity levels. DC 3.7V rechargeable lithium battery (KM 312). Multiple colors LED for leak level indicator. Extremely sensitive heated diode sensor. Automatic adjustment & reset to background (KM 312). Detects R-134a, R-410a, R-407c & R-22 etc. Microcontroller circuitry that guarantees accuracy & reliability.
-
product
Fiber Laser
ALiDAR Series
Amonics' high power fiber laser (ALiDAR) series offers eye-safe, single mode, linear polarized nanosecond-pulsed all fiber laser source with master-oscillator-power-amplifier.It is designed for three-dimensional imaging, wind detection and ranging LiDAR systems. The ALiDAR series is maintenance free with no post-installation service required. It is a versatile, ready-to-use and durable laser source for various LiDAR applications.
-
product
Auto Oxygen Sensor
KS60004
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Phase Sequence Indicators (Contact Type)
862 PR
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Neon light indicators.● Large size alligator clips for easy clipping onto switch- boards terminals.● Checks a wide range of 3-phase power sources.● Ideal for installing conveyor lines, pump systems and interconnected drivers.● Waterproof design, protection class : IP24.● Special test leads length are available on request.
-
product
Peugeot Oxygen Sensor
KS60113 - Peugeot
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Reverse Transcription and Polymerase
ThermaStop-RT
RNA oligonucleotides from cells and viruses can be amplified for detection using the methods of Reverse Transcription and Polymerase Chain Reaction (RT-PCR). In a first step, a complementary strand of DNA (cDNA) is synthesized using a primer and reverse transcriptase. The cDNA is then amplified using standard PCR techniques. This can be accomplished by taking an aliquot from the reverse transcription reaction and adding a DNA-dependent DNA polymerase (e.g. Taq) and other reagents and then doing PCR. That method is commonly called "Two-step RT-PCR", or "Two-tube RT-PCR". Alternatively, all reagents, including both enzymes and gene-specific primers can be included in a single tube in order to do both reverse trancription and PCR without the need to open the tube between those reactions. That method is commonly called "One-Step RT-PCR" or "One-Tube RT-PCR". Both methods can include primers for a single target or for multiple targets (i.e. multiplex RT-PCR).
-
product
Dynatrol® Level Switch for Light Bulk Solids
CL-10GJ
Dynatrol® CL-10GJ Level Detector operates with consistent results on problem applications that have a tendency to bridge or pack. It handles difficult products such as flour, cocoa, sugar, pharmaceutical powders, powdered lime and additional bulk solid materials for high-, intermediate- or low-point level detection. The CL-10GJ is typically used with bulk solids in the density range of 10-15 lbs/ft3.
