Reflection
-
product
Circulator And Isolator
A circulator is a three-port passive RF device that directs signals to flow in a single direction, like a one-way street for radio frequencies. An isolator is a type of circulator with one port terminated in a matched load, effectively acting as a two-port device that only allows signals to pass through in one direction and protects components by dissipating any reflected signal.
-
product
Noise Source, 10 MHz to 18 GHz, nominal ENR 15 dB
346B
The Keysight 346B noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The 346B's high ENR, low SWR, and variety of connectors make it a general-purpose noise source. Add special option H01 for high ENR (21 dB typical) to measure high noise figure devices, or option H42 for measuring Direct Broadcast Satellite (DBS) low noise block converters.
-
product
Spatial Heterodyne Surface Chemical Agent Detector
SHSCAD
Wide area, high areal coverage rate surface contaminant detection via LWIR reflectance spectroscopy employing eye safe broadband quantum cascade lasers (QCLs) and a high-speed spatial heterodyne spectrometer (SHS) in a handheld sensor package (~ 10,000 cm3, 10 lb).
-
product
Power Supplies
CUL-950B
The CUL-series is a semi-modular power supply that lets you select the cables you need while powering your gaming system with a 140mm Blue LED cooling fan and 6 pin PCI-E ready. **850W & 950W is offering 140mm Blue LED cooling fan & Dual 6+2 PCI-E ready. Everyone likes a clean and easy installation. This power supply allows you to keep what you want and remove what you don't. While necessary connectors, like the 20+4 pin power & 4+4 pin CPU connector are attached to the unit, you decide which of the others should stay. Customize your power supply to reflect your system.
-
product
Light Tach Kit
When taking vibration measurements on rotating machinery, it is crucial that you record tachometer pulses along with vibration data. A photoelectric sensor along with reflective tape that is attached to the rotating element will provide these speed pulses for data analysis.
-
product
Top View Analyzer
TVA100
Our Top View Analyzer – TVA100 is the only instrument in the world to use the top-view reflection method for measuring the contact angle of a liquid on a solid from above. The innovative measuring method is particularly suitable for measurements in depressions and on concave surfaces where drops cannot be analyzed using the conventional side view.
-
product
3D Laser Imager
Vector-DD
The Vector 3D laser imager offers multi wavelength, full waveform data capture, coupled with the flexibility of an all-sky scanner. The Vector-DD is a direct detection (DD) 3D (range, angle, angle) active imager with an all-sky full hemisphere scanner. It employs a nodal point design so that all the lines-of-sight converge to a single point at the instrument*. In addition, two wavelengths can be transmitted so that differential reflectivity information can be derived. The unit is compact and portable and operates from 24V DC.
-
product
Color Measuring Unit
Colorette 4
The Colorette 4 serves for precisely measuring the colour of ground roasted coffee. By means of the stripping device, the sample to be measured is prepared and afterwards positioned at the measuring point. The Colorette works according to the principle of reflection measurement. A ground coffee sample to be measured is illuminated with a white clock-pulsed LED. For colour value determination, the reflected light is thereby captured by a sensor. The determined colour value is afterwards indicated on the touch screen. The indication in different scales makes it possible to use the device flexibly and to adapt it individually to the requirements. Thanks to the improved components, the Colorette 4 is low-wear and guarantees most exact measuring results during the entire lifetime. The extended connectivity offers various integration possibilities into processes and systems.
-
product
Turbidity Logger Sensor
NUL-231
This sensor measures the reflected light that enters into a tube containing a solution. As solution turbidity is higher, more light is reflected and measured by the light sensor, located perpendicular to the light source.
-
product
Amplifier Built-in Ultra-compact Laser Sensor
EX-L200
Panasonic Industrial Devices Sales Company of America
The EX-L200, the one of the world’s smallest Laser Sensors with a built-in amplifier, is designed to detect minute objects with utmost accuracy. Despite its miniature size, the Thru-Beam Type (EX-L211) can detect minute objects with a diameter of just 0.3mm, and the Spot Reflective Type (EX-L221) can even detect gold wire whose diameter is a mere 0.01mm. To facilitate solving application tasks, these sensors come equipped with a Potentiometer and two indicator LEDs. For the Thru-Beam Type, reflective material on the receiver allows users to visualize the laser beam, easing beam-axis alignment.
-
product
Materials And Chemical Analysis
Anderson Materials Evaluation, Inc.
Materials characterization, failure analysis, quality control, and materials and process development services are offered. Our analytical techniques allow us to assess elemental and chemical material composition, thermal properties, coating thickness, electrochemical properties, surface chemistry, surface wetting, corrosion rates and pitting potentials, contamination and degradation problems, metallography, fractography, phase transitions, static coefficient of friction, adhesive bonding strength and causes of adhesive bonding failures, surface tension and surface energy, tensile and compressive strength, bend deflection, lapshear strength, elasticity properties, UV and visible light absorption and reflection, density and porosity, and many other material properties integral to improving your products.
-
product
Open Loop Hall Effect Current Sensors Transducers With Rectangle Windows
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a highgalvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current, DC pulse currents etc. The output of the transducer reflects thereal wave of the current carrying conductor.
-
product
Spectroradiometer
SpectraScan® PR-730
The SpectraScan® Spectroradiometer PR-730 is JADAK’s enhanced sensitivity portable solution for spectral based photometric and colorimetric light measurements, designed for applications requiring precise light measurements from a range of light sources, such as display monitors and projectors, reflective surfaces, and industrial applications (visual display testing, LED testing, film and video post-production, auto/aerospace displays, and dental color testing).
-
product
Upset Testing Machine
YQ/YQR Series
Jinan Testing Equipment IE Corporation
The series of upset testing machine are designed according to the International Standard 'Metallic Materials Upset Test Methods', especially for the quality inspection of high-speed rods and wires. Through simulating the quick impact conditions of the metallic materials during the upset and pressing, the machine truthfully reflects the instances of the quickly compressed rods and wires. Under room temperature or hot conditions, exert test force in the direction of specimen axial line, quickly compress the specimen, and then the machine can inspect the metal ability of bearing upset deformation in the specified upset ratio. The upset testing machine can also show the metal’s surface disfigurements. The upset testing machine is widely used in the steel industry, standard specimen manufacturing industry, and tools manufactures for inspecting the upset tests of metallic materials.
-
product
Gloss Meter
Shenzhen Graigar Technology Co.,Ltd.
A glossmeter is an instrument which is used to measure specular reflection gloss of a surface. Gloss is determined by projecting a beam of light at a fixed intensity and angle onto a surface and measuring the amount of reflected light at an equal but opposite angle.
-
product
TDR Structural Health Monitoring
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Structural-Health Monitoring probes the structural health of a composite part by propagating a fast electrical pulse along a distributed linear sensor which has been fabricated directly in the laminate. The sensor is formed from the native graphite fibers already used in composite manufacture, and constitutes zero defect. Fibers are patterned into a microwave waveguide geometry, or transmission line, and interrogated by a rapid pulse as shown below. Structural faults along the line cause distortions in waveguide geometry, producing reflected pulses similar to radar. Cracking, delamination, disbonds, moisture penetration, marcelling, and strain are all detected by propagation delay, for sensor lengths up to several meters.
-
product
Coaxial Open, 2.4 mm (m)
85141A
The Keysight 85141A coaxial open is used for establishing measurement planes for known reflection phase and magnitude in 50-ohm coaxial systems. It has a 2.4 mm male connector.
-
product
Loudspeaker-Microphone Probe
Zircon
The Zircon is a loudspeaker-microphone probe for measuring in situ the absorption and reflection properties of surfaces. These may be indoor surfaces, such as in concert halls and gyms, or outdoor surfaces, such as road surfaces (ISO 13472-1), sound barriers installed in a free field (NF S 31-089) and traffic noise reducing devices (CEN/TS 1793-5)
-
product
Handheld Tachometers
The handheld tachometer is a means of measuring revolutions within the industrial sector, either optically or mechanically. The handheld tachometer can be used for maintenance and calibration of machines that have moving parts. The principle is similar to a bicycle speedometer, where time will be measured until a wheel has completely turned. The handheld tachometer has two different measurement methods.The handheld tachometer may have a contact connection to the moving parts. Alternatively, the handheld tachometer works with reflecting marks. This will be secured on the moving part. As the laser strikes the reflecting mark during rotation, it will be reflected and detected in the handheld tachometer via a sensor. Rotation speed and speed can be seen on the handheld tachometer. The handheld tachometer may combine both possibilities (contact and non-contact connection). Next to the handheld tachometer you find other devices for measuring revolutions at PCE Instruments.
-
product
RF Limiter, 10 Hz to 1800 MHz
11867A
11867A RF limiter can be used to protect the input circuits of spectrum analyzers, counters, amplifiers, and other instruments from high power levels with minimal effect on measurement performance. This limiter (10 Hzto 1800 MHz) reflects signals up to 10 watts average power and 100 watts peak power. Insertion loss is less than 0.75 dB.
-
product
Production Test Stands for Electric Motors
Electric drives such as DC and EC motors are more and more extensively deployed in the automotive industry. At the same time there is an increasing requirement for a 100% analysis of motors for fault detection and error analysis as well as statistics on quality, without increasing production cycles times. The model-based Parameter Identification method (PI method) from imc allows testing to be performed under load, yet without an “explicit” separate load machine. Instead, the motor is loaded dynamically by exploiting its own inherent inertia. This allows motor parameters such as resistance, inductivity and friction to be determined within a few seconds. A mathematical model and its parameters reflect motor behaviour in its completeness and make it possible to monitor motor production based on limit values and trend statistics. The identified parameters of the model equation can then be used to calculate derived key performance indicators of the motor characteristic curve.
-
product
Non-Contact Mapping Life Time System
MWR-2S-3
The device is designed for express non-destructive contactless local measurement of non-equilibrium charge carrier effective lifetime in silicon substrates, epi-wafers and solar cells at different stages of manufacturing cycle. It can be used for incoming and outcoming inspection of silicon ingots and wafers, tuning and periodic inspection of semiconductor and solar cell technology quality. Lifetime determination is based on measuring photoconductivity decay after pulselight photo-exciting with usage of reflected microwave as a probe.
-
product
Goniophotometer Test System For Led Lamp
LCG-1680B
Shenzhen Chuangxin Instruments Co., Ltd.
Design according to IEC61341the test method of central luminous intensity and beam angle for reflecting light, this instrument can be used to test the cross section luminous intensity distribution curve, central luminous intensity and effective beam angle of LED assembled luminaries and LED lens system with diameter less than 180mm.
-
product
SP5T RF Pin Diode Switches To 12 GHz
Pulsar Microwave's 5-way RF switches cover bands from 300 MHz to 12 GHz in both absorptive and reflective configuration. These SP5T switches have a rating of 200 mW maximum input power and a switching time of 100 ns. They are specified with a minimum isolation of 60 dB and most models maintain a VSWR of 1.6:1 or better on all ports. The SP5T switches are driven by TTL logic control circuitry and require both positive and negative 5-volt supplies for operation. A 9-pin D-SUB connector provides the interface for the power and logic voltages.
-
product
Water Source Measurements You Can Count On
TechPro™ II (TP1, TPH1)
Obtain reliable and accurate measurements of your water source with the value-priced TechPro II™. Ideal for water treatment testing as well as other industrial and commercial applications, these instruments reflect Myron L®’s 55-plus years experience designing and building quality conductivity, TDS and pH measuring instrumentation.
-
product
Analytical Techniques
Anderson Materials Evaluation, Inc.
Our numerous analytical techniques, we tackle a wide range of materials challenges and commonly combines several analytical techniques to fully address complex and multi-dimensional materials issues. Our materials analysis laboratory provides XPS surface analysis, thermal analysis (TGA, DSC, TMA), FTIR infrared spectroscopy, UV-Vis spectrophotometry and reflectivity measurements, gas chromatography – mass spectroscopy (GC-MS), SEM/EDX, optical microscopy, mechanical testing, electrochemistry and corrosion analyses, residual gas mass spectroscopy, contact angle measurements, surface contamination measurements, adhesive bonding failure analysis, facility testing for silicone contamination, mechanical testing, metallography and fractography, density and porosity measurements, volatile organic component testing, friction, and other analytical capabilities. We continue to upgrade and expand our arsenal of analytical techniques and custom analytical methods to support our customers’ needs.
-
product
Hyperspectral Imaging Sensors
HYPERSPEC® sensors are line-scanning instruments (sometimes called pushbroom) that collect reflected light through an image slit. One row of spatial pixels is collected per frame as motion occurs, with each pixel containing full spectral data. Motion can be accomplished in two ways: either as an airborne deployment (UAV, aircraft, or satellite) or stationary (where motion is accomplished beneath the sensor, such as a food inspection line). A third option is also available where pan-and-tilt or rotary stages allow a fixed-location sensor to scan a stationary object (such as a piece of artwork, or a mine face for geological applications).
-
product
Spectroradiometer
Spectrascan® PR 788
The SpectraScan® Spectroradiometer PR-788 Extended Dynamic Range is JADAK’s ultra-sensitivity portable solution for spectral based photometric and colorimetric light measurements, designed for applications requiring precise light measurements from a range of light sources, such as display monitors and projectors, reflective surfaces, and industrial applications (visual display testing, LED testing, film and video post-production, auto/aerospace displays, and dental color testing).
-
product
VNIR Hand-held Spectroradiometer
HandHeld 2 Pro
Analytical Spectral Devices, Inc.
The FieldSpec HandHeld 2 Pro hand-held spectroradiometer offers greater sensitivity over the standard HandHeld 2 spectroradiometer model, aiding spectral measurements for applications with low reflectance characteristics such as water surfaces. Wherever there is a need for enhanced sensitivity, faster collection rates, high signal to noise performance, the HandHeld 2 Pro is the low cost VNIR spectroradiometer of choice.
-
product
Solar Cell Characterisation
The PVE300 permits the determination of device spectral responsivity (from which may be determined EQE), and, having performed measurements of sample reflectance (and transmittance where required) the determination of IQE.
