Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI/PXIe High Density Precision Resistor Module
42-297A-121
The 40-297A-121 (PXI) and the 42-297A-121 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 925 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Silicon Oscillators
Analog Devices silicon oscillators are frequency programmable via pin-strapping, or through the resistor connection or serial interface (SPI or I2C). These solid-state clocks are well-suited for general-purpose usage, such as PGAs, ASICS, microprocessors, or UARTS, and they operate from 1 kHz to 170 MHz. Silicon oscillators are also ideal switching regulator clocks as they provide synchronization and EMI reduction (via spread spectrum).
-
product
USRP-2955, 10 MHz to 6 GHz, 80 MHz Bandwidth, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device
785264-01
The USRP-2955 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless receiver systems. It is designed for over-the-air signal acquisition and analysis. It features a two-stage superheterodyne architecture with four independent receiver channels and shares local oscillators for phase-coherent operation. It also offers a Kintex-7 FPGA programmable with the LabVIEW FPGA Module. With these features, the USRP-2955 has the RF and processing performance for applications such as spectrum monitoring, direction finding, signals intelligence, wideband recording, and radar prototyping. The USRP-2955 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) Reference Clock, which improves frequency accuracy and synchronization.
-
product
USRP-2945, 10 MHz to 6 GHz, 80 MHz Bandwidth, Reconfigurable USRP Software Defined Radio Device
785263-01
10 MHz to 6 GHz, 80 MHz Bandwidth, Reconfigurable USRP Software Defined Radio Device - The USRP-2945 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless receiver systems. This software defined radio reconfigurable device is designed for over-the-air signal acquisition and analysis. It features a two-stage superheterodyne architecture with four independent receiver channels and shares local oscillators for phase-coherent operation. It also offers a Kintex-7 FPGA programmable with the LabVIEW FPGA Module. With these features, the USRP-2945 has the RF and processing performance for applications including spectrum monitoring, direction finding, signals intelligence, wideband recording, and radar prototyping.
-
product
Hybrid Mixers
General-purpose, high-performance microwave mixers with integrated programmable local oscillators. Great for up-converting or down-converting wideband signals.
-
product
External Input Module
EIM-01
The EIM-01 external input module is used to safely isolate and input an external drive signal into the MAC-01, -02 or -03 AC Power Sources/Frequency Converters. The unit can accept various waveforms from laboratory or programmable oscillators or from a Titan MOS-01, -01A, -01B when used as a slave unit in multi-KVA systems. BNC input is completely isolated and floating with 1,500VAC breakdown and excellent common mode rejection. A recessed 8% gain adjustment control is also provided. The EIM-01 must be factory installed.
-
product
Dual Channel Multi-Band FM Tracking/Data Receiver In Modular Style Housing
LS-27-B
The Lumistar LS-27-B Modular Dual Channel Tri-Band Tracking and Data Receiver is Lumistar’s third generation of modular high performance FM Receivers. This wideband designs supports one or two independent channels of PCM with data rates up to 20Mbps. The unit includes both an optional FM demodulated output for PCM data, and standard programmable AM/linear AGC outputs for auto-tracking receivers. The design offers 8 IF Bandwidths and 8 Video Filters per channel for each receiver.AC coupling with a low pass filter is employed to ensure a high quality data link with long strings of NRZ-L ones or zeroes. The unit provides a software selectable 10 MHz reference I/O port forlocking local oscillators to a high precision external source or to arrange multiple units in a master/slave arrangement. The receiver’s control and status is achieved via Ethernet, USB or auto-switched RS-232 (or “4-wire” RS-485 in place of 232). When utilizing the RS-422 interface, multi-drop configurations can be accommodated.
-
product
PCI High Density Potentiometer Card 2-Channel, 16-Bit, 0 To 65k Ohm
50-296A-021-2/16
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Resistor Module 2-Channel 1.5R to 2.04k
40-293-022
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
1,500 Watt AC/DC Power Supply
56WS4
NAI’s 56WS4 is a conduction-cooled, 1,500 Watt AC/DC Power Supply that converts either 3-phase, AC input or +270 VDC input into a single DC output at 1,500 Watts.
-
product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 63.7 Ohm
40-294-011
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-134
The 40-297A-134 (PXI) and the 42-297A-134 (PXIe) are 4-channel programmable resistors with a range of 2 Ω to 102 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PCI High Density Resistor Card 10-Channel, 12-Bit, 0 To 4k Ohm
50-295A-121-10/12
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 32.7k Ohm - SPST
50-294-132
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI 2.5W Programmable Resistor Module, 2-Channel, 1.5Ω to 925Ω
40-251-121
The 40-251-121 is a programmable resistor module with 2 channels which can be set between 1.5Ω and 925Ω with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI Precision Resistor Module 18-Channel, 1 to 239
40-297-013
This 18-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 510 Ohm
50-294-014
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI High Density Pecision Resistor Card, 6-Channel, 4Ω To 1.51MΩ
50-298-050
The 50-298-050 is a high density programmable resistor card with 6 channels which can be set between 4Ω and 1.51MΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI High Density Precision Resistor Module, 4-Channel, 2.5Ω to 925Ω
40-298-121
The 40-298-121 is a high density programmable resistor module with 4 channels which can be set between 2.5Ω and 925Ω with 0.25Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 1.81kΩ
50-298-122
The 50-298-122 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 1.81kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
300-Watt AC/DC Power Supply
Model 56RS1
NAI’s 56RS1 is a 300 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides a single full-power output at a baseplate temperature of +85° C.Standard features include remote error sensing; remote digital (TTL) turn on/off; and protection against transients, overvoltage, overcurrent, and short-circuits. Options such as ESS vibration testing and choice of output voltages are available, and additional options and special units can be ordered.
-
product
PXI 2.5W Programmable Resistor Module, 1-Channel, 3Ω to 11.4MΩ
40-251-153
The 40-251-153 is a programmable resistor module with 1 channel which can be set between 3Ω and 11.4MΩ with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-053
The 40-297A-053 (PXI) and the 42-297A-053 (PXIe) are 6-channel programmable resistors with a range of 3 Ω to 11.4 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PCI High Density Potentiometer Card 2-Channel, 12-Bit, 0 To 4k Ohm
50-296A-021-2/12
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI 9-Channel Precision Resistor Card
50-297-101
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-042
The 40-297A-042 (PXI) and the 42-297A-042 (PXIe) are 6-channel programmable resistors with a range of 2.5 Ω to 395 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-110
The 40-297A-110 (PXI) and the 42-297A-110 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 31 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI Precision Resistor Module 18-Channel, 1 to 31.5
40-297-010
This PXI precision resistor provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-016
The 40-297A-016 (PXI) and the 42-297A-016 (PXIe) are 18-channel programmable resistors with a range of 1 Ω to 1.8 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI/PXIe High Density Precision Resistor Module, 4-Channel
40-297A-123
The 40-297A-123 (PXI) and the 42-297A-123 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 3.55 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-055
The 40-297A-055 (PXI) and the 42-297A-055 (PXIe) are 6-channel programmable resistors with a range of 3 Ω to 43.8 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
