Transducer Amplifiers
Increase a transducers signal to measurable levels.
-
Product
Linear Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOMs linear amplifiers offer high IP3, power up to 2.5 W and are offered in a variety of DIE and package types to simplify point-to-point wireless, SATCOM/VSAT, and radar system design.
-
Product
16-Channel Instrumentation Amplifier
PGA-16
-
The PGA-16 is a 16-channel instrumentation amplifier with differential input, single-ended output, programmable AC or DC input coupling and pre-filter gain.
-
Product
Low Noise Amplifier
-
Low noise amplifiers, or LNAs, are designed and manufactured by utilizing the most advanced PHEMT or MMIC devices, thin film technologies, and an improved DC power supply to deliver a low noise performance with broad operating bandwidths and good gain flatness. While standard models focus on general purpose applications, additional models with differing frequency ranges, gains and noise figures are listed on the website. Custom designs are also offered to meet any user’s specific needs.
-
Product
Clamp-on Transducer
CA1000D
-
Measure current without disconnecting circuit under test. Measure to 1000A DC or AC. Outputs 1mV per Amp, operates on 2V range of any DMM.
-
Product
Logarithmic Video Amplifiers
DLVAs, ERDLVAs & SDLVAs
-
PMI’s Detector Logarithmic Video Amplifiers (DLVA, ERDLVA, SDLVA) are offered covering DC to 40 GHz with extended range models offering dynamic ranges over 70 dB. Our standard products provide exceptional temperature stability, log linearity and frequency response. As well, most SDLVAs provide a limited IF output. PMI offers custom DLVA’s and SDLVA’s to meet your requirements or replace obsolete products, please email your requirement to sales@pmi-rf.com so we can propose an instant solution.
-
Product
Transducer & Isolator
-
Measured parameters can be programmed to generate equivalent output signalsOverride selection for desired value and rangeIsolation between input to output or output to outputQuick response time of 300ms in display and communicationOn field configurable Input and Output parametersUser friendly interface to support remote monitoring and communication
-
Product
AC Current Isolated Sensor Two / Four Wire Transducer
TSCT (Average Sensing) / TFCT (TRUE RMS)
-
Kusam Electrical Industries Limited
• Transform Input: AC 5~400A directly into DC 4~20mA, no need external CT.• Suitable for application with high waveform distortion :(Frequency converter, Motor, SCR )• High accuracy ＜0.5%• High response time• High stability, easy connection.
-
Product
Transducers with 4-20 mA Output
-
Transducers / transmitters for temperature, humidity, atmospheric pressure and CO2 with 4-20mA interface.
-
Product
Instrumentation Amplifiers
HIGH-POWER RADIO FREQUENCY (RF) AND MICROWAVE AMPLIFIERS, TWTA AND SOLID STATE
-
Communications & Power Industries
electromagnetic compatibility (EMC) high-intensity radiated field (HIRF) testing, military testing, electronic warfare simulation and scientific applications are based on the same switched-mode power supply technology as its rugged amplifiers. As a result, these instrumentation amplifiers have all the same performance and reliability advantages as the rugged product line, but have been neatly re-packaged into compact, lightweight and affordable rack-mountable units more suitable for less demanding physical environments. CPI TMD's new modular design (the PTCM range) has many user benefits, including advanced self-diagnostics, ethernet interfaces, remote management, VSWR protection and plug and play field replaceable power supplies.
-
Product
Amplifier Gain Blocks
-
Macom Technology Solutions Holdings Inc.
At MACOM we design, manufacture, and support a wide portfolio of Amplifier Gain Blocks for RF, microwave, and millimeter wave applications. Our amplifier gain blocks cover frequencies ranging from DC to 45 GHz. MACOM’s gain blocks are used in a variety of 50 Ohm and 75 Ohm applications including; Networks, Commercial and Aerospace and Defense. Leveraging the latest innovative technology these products are available in both standard plastic packaging and bare die.
-
Product
C & L-Band Separate Raman Fiber Amplifier
RFA7000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
Explosion-Proof Transducer
HX
-
Computer Conversions Corporation
Computer Conversions Explosion-Proof Transducer Housings are designed to operate in hazardous environments requiring an Explosion-Proof Enclosure. Suited with internal (Factory Installed) resolver-transducers; these units can be provided as part of an absolute and/or incremental encoder system. Most transducer cables only require six conductors, shielding is optional, and systems are capable of maintaining 1000' cable runs in severe RFI environments.
-
Product
Amplifier
-
Toellner Electronic Instrumente GmbH
An electronic device that increases the voltage, current, or power of a signal.
-
Product
Pulsed Injection Locked IMPATT Amplifiers
-
Pulsed injection locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Product
RF Bidirectional Amplifiers
-
Miniature, high-efficiency and linear bidirectional amplifier modules (transmit and receive). 1.0 to 2.5 GHz, automatic or manual T/R switching, high-efficiency or high-linearity models. Custom designs available through RF PA design services.
-
-
Product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800C (3RU)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800C (3RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
Product
Wireless Transducers with GSM Modem
-
Wireless GSM data loggers for temperature, humidity, binary-u. counter input.
-
Product
Distribution Amplifier
-
AVLINK TECHNIC TAIWAN CO., LTD.
Is a device that accepts a single input signal and provides this same signal to multiple isolated outputs.These devices are important because they allow a signal to be distributed to multiple destinations without ground loops or signal degradation. They are used for a number of common engineering tasks, including multiple amplification, cable television, splitting monitor and front of house mixes, and "tapping" a signal prior to sending it through effects units to preserve a "dry" signal for later experimentation.
-
Product
Waveform Amplifier 30 Volts Pk-pk
WA301
-
Extends the output range of function generators30 Volts peak to peak output swingDC to 1MHz bandwidthHigh impedance input, 0dB to +20dB gain50 Ohm and 600 Ohm outputs20dB switchable output attenuatorFully protected output
-
Product
Hydrodynamic 33 kHz and 200 kHz Dual Frequency Transducer
Model TC2178
-
Model TC2178 is an optimized and hydrodynamic 33 kHz and 200 kHz dual frequency transducer ideal for navigation and hydrographic echosounder systems. The transducer has excellent piezoceramic elements which will ensure the highest reliability and quality in echosounding.
-
Product
Low Power Op Amplifiers (< 1mA/amp)
-
Analog Devices low power op amps offer a variety of benefits in many applications such as prolonging battery life, easing waste heat management in end equipment, reducing self heating to minimize thermally induced offset shift, and reducing total system power consumption and cost. Offering power efficient devices without compromising speed, noise, and precision has been a key focus on developing products at ADI.
-
Product
RF POWER AMPLIFIERS
BLWA Series
-
A) RF-Sample Ports I) 3x 208 V AC / 60 HzB) External Dual Directional Coupler L) LAN Remote ControlC) IEEE-488.2 GPIB Remote Control S) Internal RF Switching UnitD) Front Panel RF Connectors R) RS-232C Remote ControlE) RF Power Indication (digital) U) USB Remote ControlF) Gain Adjustment W) Liquid CoolingH) DC Supply X) External Control of other Amplifiers
-
Product
Headphone Amplifier
MH-8
-
High-power headphone amplifier that distributes the stereo input to eight headphone outputs
-
Product
In-Line Charge Amplifiers
-
The in-line charge amplifier is used to excite structures or machinery with a definable impulse force. Resonances are identified by impulse, an important measurement parameter for the study of dynamic behavior. The 4705A1 is a fast turn on time, 50 mV/pc, in line charge amplifier with BNC jack connectors on each side.
-
Product
YDFA Amplifier
-
a high-gain three staged polarization maintaining optical amplifier unit designed for applications requiring high efficiency optical amplification in the 1060 nm regime in both CW and pulse mode operations.
-
Product
AC and DC Current or Voltage Transducers
VT7 AND VT8 Series
-
The Model VT7 Series dc voltage transducer produces an output which is directly proportional to the input from dc to 10kHz. It functions as a millivolt dc shunt or a high voltage isolator to 1000V
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Optical Parametric Amplifier
-
AVUS is an Optical Parametric Amplifier (OPA) that provides widely tunable high energy pulses and high repetition rates (up to 1 MHz). AVUS offers highest average output power on the market and is designed for 1 µm fs pump lasers.
-
Product
Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier
USBPGF-S1
-
Single Channel USB Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier for Signal Conditioning in Data Acquisition Systems. Differential or single ended input. 10Vmax Signal Input and Output with input protection up to 40V. Software-programmable instrumentation amplifier gains of 1 to 1000.
