Compensators
-
product
Pressure Sensor
MLV Series
The MLV Series Compensated Sensor is based on All Sensors’ CoBeam2 TM Technology. The device provides a high output signal at a low operating voltage while maintaining comparable output levels to traditional equivalent compensated millivolt sensors operating at higher voltages. 1 inH2O to 150 PSI Pressure Ranges.
-
product
6GHz RF Signal Generator
TGR6000
0MHz to 6000MHz frequency range10Hz setability, ±1ppm frequency stabilityLocking to external frequency standard-110dBm to +7dBm amplitude, 0.1dB stepsFast stepping sweep with dwell times down to 10msList sweep of up to 1000 points of amplitude vs frequencyUser compensation tables for specific test set-upsStorage for 12 generator set-ups and 16 sweep listsCompact half-rack 2U casing uses minimum bench spaceFull remote control through RS232, USB, LAN and GPIBSignificantly lower cost than other 6GHz generators
-
product
X-Band Silicon Radar Quad Core IC
AWS-0105
The AWS-0105 is a highly integrated silicon quad core IC intended for radar and 5G phased array applications. The device supports four radiating elements, single beam transmit, and single beam receive and includes all requisite beam steering controls for 6 bit phase and gain control. The device provides 21 dB gain and +15 dBm output power during transmit mode and 7 dB gain and +7 dBm IIP3 during receive mode. Additional features include gain compensation over temperature, temperature reporting, and fast beam switching using eight on-chip beam weight storage registers. The device features ESD protection on all pins, operates from a +1.8 V supply, and is packaged in a 56 lead 7x7 mm QFN for easy installation in planar phased array antennas.
-
product
Pressure Transmitter
PS2
- Digital temperature compensation and nonlinear correction- High sensitivity, high precision, high stability- Full temperature compensation, good electrical performance and long-term stability- The plug and shell are integrally spin-stable, stable and waterproof, to avoid loosening the thread of ordinary plug- A variety of signal outputs, convert the pressure of the measured medium into 4~20mA,0~10VDC analog signals, RS485 digital signals- With RS485 communication interface, the monitoring system can easily read the measured value- The shell adopts laser welding, high reliability, long life, long-term stability and reliability
-
product
2210A & 2211A Quartz Frequency Standards
Precise Time and Frequency, Inc.
The ptf 2210A Quartz Frequency Standard has been designed to provide a highly stable and spectrally pure frequency reference for applications requiring the ultimate in short term frequency performance.The instrument contains a double oven controlled stress compensated (SC cut) quartz crystal oscillator (OCXO) to give the ultimate in performance.Ideal for laboratory or system use, the unit provides good stability performance at lower cost and with improved phase noise.
-
product
Precision AC/DC Current Shunt
1625A
The BLI 1625A is a multiranging, high accuracy, active current shunt, for use in making NIST traceable measurements of currents from 10 microamperes to 100 Amperes. Very high measurement stability has been achieved in our shunt design by using special alloys, compensated by a proprietary Ballantine process to minimize temperature coefficient effects.
-
product
Precision Capacitance Meter
TH2638B
Changzhou Tonghui Electronic Co., Ltd.
TH2638 series is a new precision capacitance meter with higher test frequency. With small size and portable appearance, it is convenient for use on the shelves. With basic accuracy of ±0.07%, loss accuracy of 0.0005, test frequency up to 1MHz, 4.3-inch LCD screen, selectable Chinese-English operation interface, TH2638 series is easy to operate and provide fast and reliable test for ceramic capacitor production. Also, it can test all kinds of capacitors from low value to high value. The results of testing one capacitor for several times are quite stable and accurate, even for lower value capacitors. The tester is compatible with SCPI command set, and configured with manipulator and scanner interface, the scanner interface can scan the open/short/ load error calibration in each channel, 256 channels at most. In low frequency, there is signal level compensation function. When the impedance is very small, the internal resistance in signal source and test cable will cause the voltage on terminal of DUT lower than the set range, then this function will adjust the level to the set range.
-
product
PDS Motionscan Software
Allows a 3D Scanning sonar user to collect motion compensated 3D point clouds from a moving platformTeledyne PDS MotionScan system allows a 3D Scanning sonar user to collect motion compensated 3D point clouds from a moving platform. The MotionScan system is comprised of: an RTK capable dual antenna GPS with precision heading output, a heave, pitch and roll sensor, a topside control console. In combination with a BlueView 3D Multibeam Scanning Sonar this creates a full survey package.
-
product
Temperature Compensated Crystal Oscillators
TCXOS & VCTCXOS
Temperature Compensated Crystal Oscillators (TCXO) deliver excellent temperature characteristics combined with low power consumption and fast warmup. Voltage Controlled Temperature Compensated Crystal Oscillators (VCTCXO) combine the same excellent temperature characteristics, low power consumption and fast warmup with a voltage control function to allow precise tuning of the output frequency after PCB assembly and later, to compensate for any effects of aging as well as offering the ability to pull back to nominal frequency where there is a change of circuit conditions
-
product
Passive Probe
PP011-1
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
product
Mid-Range Gas Filter Correlation CO2 Analyzer
Model N360M
Teledyne Advanced Pollution Instrumentation
The Model N360M measures carbon dioxide (CO2) by comparing infrared energy absorbed by a sample to that absorbed by a reference according to the Beer-Lambert law.The N360M uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb IR. The analyzer passes the IR beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO2 known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO2 in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure. A nitrogen purge system is provided for the GFC wheel assembly to eliminate the effects of ambient CO2, if necessary.
-
product
16 Thermocouples/RTD Ch
APCI-3200-16
18-bit resolution, 16-bit accuracyEach channel can be configured either for thermocouples/RTD or as an analog voltage input channel16 analog input channels for thermocouple typesJ, K, T, E, R, S, B, N - or 8 diff. analog input channels for the acquisition of resistance temperature detectors (Pt100)- or 16 SE/8 differential analog voltage input channels, ± 2.5 V8 independent current sources for resistance temperature detectors (RTD) and one current source for cold junction compensationCold junction compensation (on separate screw terminal board PX 3200)Gain and offset calibrationLinearisation through table and calculation for the thermocouple types J, K, T, E, R, S, B, N and RTDsProgrammable gain16-bit accuracy with sample rates of 20, 40, 80 or 160 Hz (other rates on request)4 digital input channels, 24 V and 3 digital output channels, open collector, isolated
-
product
Venable Stability Analysis Software
In 1983, Venable launched the renowned K-Factor Technique, still in use by many instrument manufacturers today. Venable has elevated the original software with its innovative Stability Analysis program. Go straight from measurement to design using Stability Analysis as its dynamic functionality eliminates lengthy manual value calculations and guesswork. Compensation amplifier synthesis capability, or coefficients for digital power supplies, enables user to achieve exact feedback loop bandwidth and phase margin desired on the first try.
-
product
SINE M-15-60 Sinusoidal Array
The reflective Sinusoidal Array SINE M-15-60 is similar to the M-13-60 (1X version) except that the range of spatial frequencies begins with 0.25 cycles per mm and extends to 20 cycles per mm. To compensate for the additional frequencies, the 3/16 cycles per mm area has been eliminated. Both arrays are imaged on Photo Paper.
-
product
HDMI Test Connector
The plug contact consists of a test plug for the transmission of the digital signals that meet your specific requirements and a suitable adapter (mounting unit). Due to their built-in rubber buffers, the mounting shoes have different degrees of freedom and allow a self-centering contact. Because of these flexible fixing tolerances on the product and in the contact area can be compensated (for example in case of misalignment or deviations in the assembly). The plugs can be easily integrated into test fixtures or contacting modules. By a suitable cable assembly, the plug is connected quickly and solderless to the measuring system. This makes it easy to replace the test plugs while maintaining the system.
-
product
Reactive Compensation and Generator Testing Instruments
Wuhan Huatian Electric Power Automation Co., Ltd.
Reactive Compensation and Generator Testing Instruments by HVTEST
-
product
Brix Meter
Hand-held, digital brix meterLight-weight, portable, includes protective carrying caseMeasures concentration of sugar and dissolved solids in aqueous solutionAutomatic Temperature Compensation (ATC)Ideal for on-site measurement of juices and other sugar-based liquidsDetermine fruit quality during harvest, shipping, receiving, processing, storage
-
product
EIS Battery Analyzer
BA8100
The BA8100 is designed to accurately measure the internal impedance of a single cell or battery stack with voltages as high as 80 V. In addition to impedance, auxiliary measurements include voltage, current, phase, capacitance, inductance, quality factor and more. With the provided software, the BA8100 can perform Electrochemical Impedance Spectroscopy (EIS) across a frequency range of 50 mHz to 10 kHz. The impedance spectrum can be evaluated through the Nyquist and Bode plot tools to determine effective series resistance (ESR) and track battery health. Included with the BA8100 is a self-test fixture to verify the instrument’s performance or compensate for resistance introduced by the test leads.
-
product
D-Coupon Generator
Conductor Analysis Technologies, Inc
This coupon generator is based on the D-Coupon of IPC 2221B Appendix A. It is advised that you familiarize yourself with the coupon specifications before using the generator. It is also recommended that the drill, etch and soldermask fabrication compensations be applied uniformly to both the coupons and product board after the coupons have been designed.
-
product
Differential Pressure Sensor for Gases
The differential pressure sensors from Sensirion measure reliably, fast and long-term stable. The fully calibrated and temperature compensated sensors offer highest accuracy and resolution, especially at very low differential pressures. The small and cost-effective design makes them an ideal match for price-sensitive solutions, e.g. in medical and HVAC applications.
-
product
MAX Waterproof pH/ORP/Temp Logging Portable Meter
MW106
The Milwaukee MW106 MAX Waterproof 3-in-1 pH/OPR/Temp. Logging Portable Meter has won fans around the world with its reliable, fast and simple operation as well as its toughness and IP67 Waterproof rating. Accurate to ± 0.002 pH with automatic or manual temperature compensation, and built in GLP key. Ideal for use by brewers, wine makers, growers, labs, food processing, water treatment and many other applications with challenging pH measurement needs.
-
product
External Pre-amplifiers
Although all Spectrum A/D cards have a very powerful input section with a highly configurable input amplifier and a variety of input ranges it is sometimes necessary to have additional external amplifiers if the signal to acquire has an extremely low level. Spectrum offers a range of perfectly matching external amplifiers to cover such cases. These powerful amplifiers have been rated using the Spectrum cards and offer best performance together with high amplification rates.The amplifiers are simply connected between the signal source and the Spectrum A/D card input and can be manually switched between different settings using small lever keys. All amplifiers allow the offset compensation by using an adjustable screw.
-
product
4 Inputs Satellite Multi-Switch
HJMS-4400A (Cascadable)
Hangzhou Huatai Optic Tech. Co., Ltd.
*4 satellite IF inputs. *Built-in amplification circuit to compensate cable loss. *13/18V.22KHz switching. *Suitable for residential multiple LNBs reception. *Use receiver power as power supply. *Sheet Metal Housing.
-
product
Liquid Flow Controllers
LC-series
Alicat Scientific, Incorporated
The LC-series liquid flow controller uses Alicat’s patented laminar flow design to provide users with fast, accurate, and stable volumetric flow control for water or selected other liquids (see Quick Specs below). At the heart of Alicat’s LC-Series liquid flow controllers is an internally compensated, laminar differential pressure measurement technology that yields linear results over a wide flow range.
-
product
Junction Boxes
Junction boxes are used for complex power and signal distribution. The junction boxes have redundant mechanical barriers. The mechanical integrity of the junction box is verified during helium leak testing and hydrostatic testing of the jumper assembly. Thermal and pressure compensation is provided by the radially compliant hose or by purpose built bladder compensators, hose lengths must be sized according to the junction box internal dead volume.
-
product
Thickness Gauges
CMX
The CMX has all features of the MX & MMX gauges with a ton of advanced features. Measure material and coating thickness simultaneously, while still detecting pits & flaws in a single mode (PECT). Auto probe zero, auto probe recognition, auto temperature compensation are also included. Selectable Large Digits and B-Scan display options, up to 64 custom user definable setups, selectable transducer table for precision linearity, and material and coating calibration options are also available.
-
product
Absolute Quantum Gravimeter
The Absolute Quantum Gravimeter is the only quantum gravity sensor available on the market place. Thanks to its disruptive technology, this instrument offers unique features:*Absolute gravity measurement at the µGal level.*Automated Continuous Data Acquisition for several months. No long-term drift.*Excellent immunity to ground vibrations thanks to an active compensation system (no mechanical isolation).*Easy and quick operation : the AQG is ready to measure within 1h (no laser alignment nor mechanical assembling, no preliminary pumping, no superspring). User-friendly software requiring no knowledge in quantum physics.*Compact and transportable sensor.*Low maintenance constraints (in particular, no moving parts in our vacuum chamber).*Station to station repeatability of the absolute measurement within a few μGal.
-
product
Digital Absolute Pressure Meter
Model KM 8070
Kusam Electrical Industries Limited
KM 8070 is an absolute pressure measuring instrument with 8 units (Pa, hPa, mbar, mmH2O, mmhg, inHG, in H2O, psi). It is normally used to measure absolute pressure, e.g. for pressure compensation in velocity measurement in ducts, laboratories and production processes. Barometric measurement and height measurements between two points are also possible. With hold, MAX, MIN, and AVG function, KM 8080 is widely used in HVAC, Laboratories and architecture project. With our reputation for quality products, you can find it is the most economic instruments for pressure meter.
-
product
Brinell Hardness Tester
Sinowon Innovation Metrology Manufacture Ltd.
◆ Equips with OS Win10, and already installed BrinScan V3.0 Auto Brinell Measurement software.◆ Apply vision measurement technology, one key operation, realize auto loading, dwell, unloading and indentation measurement.◆ AutoBrin AB-3000V can display data statistics, hardness conversion, limitation setting, graph, measurement mode setting, etc.◆ Loading by high accuracy force sensor , and can compensate force loss during loading by micro central processing unit.
-
product
Compensating Reactor
RCTD
This module is properly designed for testing Tan Delta in rotating machines with TD 5000 and allows increasing the test current and getting the maximum test voltage with high capacitive burdens
