Dielectric Strength
-
Product
IEC60065 Dielectric Strength Tester
PG-K02
-
Shenzhen Chuangxin Instruments Co., Ltd.
The IEC60065 Dielectric Strength Tester is mainly used for testing thin-layer insulation material electric strength.and IEC60065 Dielectric Strength Tester is with ISO17025 Calibration Certificate
-
Product
Multifunctional Safety Tests
-
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
Product
High-Voltage Test Hood
HVE900
-
The large, bright test room with a ball-bearing cover is designed for high production quantities. Thanks to the easily exchangeable exchangeable plate, retrofitting for testing different products is also a simple task. Product properties: External dimensions (W * D * H) approx. 940 * 716 * 640mm Usable test space (W * D * H) approx. 750 * 500 * 460mm Contacting Installation space approx. 100mm high under removable plate Dielectric strength min 10kV Application area up to 2000m above sea level Pollution degree 1 without condensation Standard conformity EN50191 / EN61010-1 Schmersal safety switch AZM161 with guard locking Lid is supported by ball bearings for high number of cycles, the bearings can be easily exchanged for servicing Optionally available, Not included in the price: - Red / green signal light - Mobile substructure trolley with 19 "
-
Product
Potentiometer, Level Transmitter, Position Transmitter
Model TWP / TWP2
-
Kusam Electrical Industries Limited
• Aux. Power AC 85 ~ 265V or DC 85 ~ 300V• High Accuracy 0.1% RO at 23 ° C - 5 °C• Input / Output User Selectable• PC Plastic Case, DIN Rail or Wall Mounting• High Dielectric Strength (AC 1.5KV/Min, between Input / Output / Power)
-
Product
DC Isolating Transmitter
Model TW2D
-
Kusam Electrical Industries Limited
• 2 Inputs / 2 Outputs User Selectable• High Accuracy 0.1% RO at 23 °C ± 5 °C• Aux. Power AC 85 ~ 265V or DC 85 ~ 300V• PC Plastic Case, DIN Rail or Wall Mounting• High Dielectric Strength (AC 2KV/ Min, between Input/Output/Power)
-
Product
DC Hi-Pot Tester
3010HP, 3025HP & 3050HP
-
The DC Hi-Pot test is an important part and parcel of the electrical safety tests mandated by standards organization world-wide. More than 80 per cent of faults in electrical and electronic systems are due to weak insulation caused by environmental factors such as dirt, grease, temperature stress, humidity, etc that affect the dielectric strength of the insulation material.
-
Product
Three Cups Insulation Oil Dielectric Strength Tester
STY Series
-
Chongqing Assen Power Equipment Co., Ltd
STY series three cups insulation oil dielectric strength tester uses a microprocessor to automatically complete boost, keep stirring, static discharge, calculate, print and other operations, is a necessary measure in the conventional test equipment.
-
Product
Insulating Transformer Oil Test Set
-
NMC make Insulating BDV Oil Test Set are used to check the di-electric strength of the transformer oil.
-
Product
Oil Breakdown Voltage Tester
-
A specialized device used to measure the dielectric strength of insulating oils until it becomes conductive.
-
Product
Fully Automatic Transformer Oil Test Set
-
1. Test as per International standards NMC insulating oil testers are fully automatic micro controller based system,completely self-contained,compact and portable giving smooth variable test voltage from 0 to 60, 80, or 100 kV for testing the dielectric strength of insulating oil in accordance with all international standards like IEC156/IS6792/ASTM D 1816/ASTM D877/ UNE 21 specifications.2. Auto mode NMC insulating oil testers are fully automatic type.1) IEC-156, IS6792, ASTM D 877, ASTM D 1816, UNE 21.2) Withstand Test A3) Withstand Test B4) 5 Minute Test5) User defined3. 100 Test results storage capacity NMC insulating oil testers has a storage capacity of 100 test results which can be recalled and printed.4. LCD display NMC insulating oil testers use LCD for easy readability of the BDV test results.5. Built in printer The printer used is a thermal paper print outs.The paper rolls can be easily installed by any person.6. User Friendly RS 232 Interface RS 232 interface is very easy to use to communicate stored data which can be saved in text format.7. Safety protection Safety interlocks are provided on the test chamber.Zero interlock protection to ensure operator safety.8. Accurate Performance The kit not only has all basic functions of an insulating oil tester but also has unique features that are seldom seen in similar products. For e.g. PROOF test A, PROOF test B, 5 Minntes test, LCD to display all test data.It ensures high work efficiency and reliability in any tough environment.
-
Product
RTD Isolating Transmitter
Model TWR / TWR 2
-
Kusam Electrical Industries Limited
• Aux. Power AC 85 ~ 265V or DC 85 ~ 300V• High Accuracy 0.1% RO at 23 °C ± 5 °C• Input / Output User Selectable• PC Plastic Case, DIN Rail or Wall Mounting• High Dielectric Strength (AC 1.5KV/Min, between Input / Output / Power)
-
Product
High Quality Transformer Oil Dielectric Strength Tester
AS-023A
-
Chongqing Assen Power Equipment Co., Ltd
AS-023A Series High Quality Intelligent Transformer Oil Dielectric Strength Tester is specially designed for testing dielectric strength (Breakdown Voltage) of transformer oil. The breakdown voltage (dielectric strength) is one of the most important parameters of transformer oil, it is a rule of the voltage withstand. The value of breakdown voltage (dielectric strength) indicates whether the oil contains water, impurity and electric particles, and you’ll know the oil value via the breakdown voltage (dielectric strength).
-
Product
Hipot Tester
Sentinel
-
The Sentinel series of test instruments has been built to provide a cost effective, yet powerful solution to hipot testing, whether on a production line or in a laboratory environment for compliance testing purposes. With the ability to perform either 5kV AC or 6kV DC dielectric strength tests and up to 500VA AC power output the Sentinel series can aid testing to many international safety standards including IEC, EN, UL and CSA to name but a few.
-
Product
High Voltage Oil Test Set
-
Supreme Instrument Laboratories
Supreme High voltage Oil Testing Apparatus is designed for testing of dielectric strength of transformer Oil or any other insulating liquids. It constitutes a complete equipment and apart of an A.C. supply of 230 / 240 Volts, no other supplementary facilities are required for its operation.
-
Product
AC & DC DIELECTRIC STRENGTH TESTERS ( HIPOTS )
AV/DV-25VA-5
-
A C & DC DIELECTRIC STRENGTH TESTERS ( HIPOTS ).
-
Product
Power Factor Transducer
*(0.2%ACC.) : TDPF. *(0.5%ACC.) : TSPF
-
Kusam Electrical Industries Limited
• Dual Aux. Power 110/220V AC• High Accuracy 0.2% RO at 23 °C± 5 °C• High Dielectric Strength 2.6KV AC / Min, Between Input / Output/ Power Case• ABS Plastic Case, DIN Rail or Wall Mounting
-
Product
Power Frequency Transducer
PP1S
-
1. Measuring and conversion IEC 6882. Dielectrical strength IEC 688 4 KVac / 1 min.3. Impulse test ANSI C37.90 / 1989 IEC 255-3 5KV ( 1.2 x 50 us ) 3KA ( 8 x 20 us ) - current coil4. Surge test (ring wave) ANSI C37.90 / 1989 ( 3KV - 0.5us / 100KHz ) IEC 255-3 ( 2.5KV - 0.25ms / 1MHz )5. Adaptability for power system VDE 0110 6. Measuring reliability VDE 3540
-
Product
Compressive Strength
-
Compressive Strength testers are used to determine the compressive strength development, gel strength development and elastic moduli of oil well cement under simulated downhole conditions.
-
Product
Dielectric Assessment Kit
DAK
-
Schmid & Partner Engineering AG
The Dielectric Assessment Kit (DAK) is ideal for all applications where high-precision dielectric parameter measurements (permittivity, conductivity, loss tangent) are required, including applications in the electronic, chemical, food, and medical industries. The dielectric probes are designed for fast, precise, non-destructive, and user-friendly measurements of liquids, solids and semi-solids over the 10 MHz – 67 GHz frequency range.
-
Product
Strength Meter
NOVOTEST IPSM-U+T+D (Pulse Velocity Tester)
-
The pulse velocity tester IPSM-U+T+D allows to measure the strength and homogeneity of the concrete, bricks and other materials under the composition and surface sounding in products and designs for construction projects, inspection of buildings and structures, according to ASTM C597-16 (Standard Test Method for Pulse Velocity Through Concrete). Has the determining of the depth of cracks by the surface sounding probe function and also flaw detection mode (A-scan).
-
Product
Bursting Strength Tester
-
TESTEX Testing Equipment Systems Ltd.
Bursting Strength Tester is used to test the strength of bursting for fabric. When you do bursting test, mullen burst tester is a wise machine for you.
-
Product
Automatic Dielectric Tester
LD-LADT-A10
-
Automatic Dielectric TesterLD-LADT-A10is a fully automatic oil tester. The oil tester adopts industrial SCM to control which is applied to integrate circuit. It features anti-jamming technology which largely improves the machine capacity.
-
Product
Touch-Screen Paper Bursting Strength
DRK109B
-
Shandong Drick Instruments Co., Ltd.
DRK109 touch-screen paper bursting strength tester, an international general Mullen instrument , is basic instrument for measuring the strength of paper and board. This instrument being simple to operate, with reliable quality and advanced technology is the ideal instrument of scientific research units, paper manufacturers, packaging industry, quality inspection departments.
-
Product
Solid Dielectric Test Cell
-
• 3 terminal design • 70pF at 1mm gap nominal capacitance • Max test voltage of 2.5kV AC or DC • Suitable for use with Eltel models DTR-3K, ADTR-2K Plus Test Sets
-
Product
High Load Strength Tester
HLST1000Z
-
This tester measures the tensile or compressive strength of various samples
-
Product
Signal Strength Analyzer
1160
-
Eliminate trips to a site with TESCO’s CAT. 1160 Signal Strength Analyzer. When a meter is not reporting reliably to the Head-end, or for a new meter, concentrator, or antenna installation, TESCO’s SSA will show you the best location for the equipment. Be certain that your antenna placement is in the best location. The SSA actually joins the network, locates and analyzes all the neighbors, and provides a visual indication of the relative signal strength, quality, and throughput of each of them.
-
Product
Dielectric Cure Monitor
LT-451
-
The LT-451 Dielectric Cure Monitor is a versatile instrument designed for research and development, quality assurance/quality control, and manufacturing applications involving thermoset materials such as resins, composites, and paints and coatings.
-
Product
Dielectric Probe Kit
N1501A
-
The Keysight N1501A dielectric probe kit with N1500A materials measurement software suite with Option 004, and a Keysight network analyzer, determines the intrinsic electromagnetic properties of many dielectric materials. Because these properties are determined by the molecular structure, they can be related to other properties of interest as well. Measuring them can provide critical insight into applications in many industries.
-
Product
Dielectric Material Test Fixture
16453A
Test Fixture
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
Product
Dry Dielectric RF Coaxial Loads
-
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
