Dielectric Strength
-
Product
Field Strength Meter
FIM-72A UHF
-
The Model FIM-72A is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-72A is suitable for practically all types of RF emission measurements in the 450 MHz to 960 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and meter dynamic range of either 20 dB or 60 dB. A dc analog voltage, proportional to meter indication, is provided for driving a chart recorder or similar device. A leveled output from the calibrating generator is available for measuring cable insertion loss, filter response, amplifier gain, VSWR, and other signal ratio measurements. The 4-1/2 inch, taut band, mirrored scale meter is calibrated in volts and dB for precise measurements in field or laboratory environments.
-
Product
Portable Single Yarn Strength Tester
TY420
-
TESTEX Testing Equipment Systems Ltd.
Portable Single Yarn Strength Tester. Used to test the breaking strength of yarn on the scene or in the lab. The instrument is controlled by micro computer. It can process the data automatically and send them to the printer. It is necessary & essential to estimate the technical index of the yarn.
-
Product
Tensile Strength Tester
-
Capacity of Tester with accuracy of 100g : 250 Kgf. and 500 Kgf.Capacity of Tester with accuracy of 10g : 20 Kgf, 50 Kgf and 100 KgfS Type Load Cell fixed with Top GripTraverse Speed: 300 & 100mm /min.Grip Separation: 1000 mmGrip Separation: 25 mmTop Grip is fixed and Bottom Grip is Movable Type.Elongation measurement by Steel Scale and Digital Counter Meter Both.Digital Display of Load and Elongation.Peak value of last test can be read.User friendly key panel with switch of zero setting and peak value of last testMotor: 1/2 HP single phase 220V 50 Hz. ( for Capacity up to 100 Kgf )Motor: 1 HP single phase 220 V 50 Hz ( for Capacity up to 500 Kgf)Power: 220 V AC 50 Hz.Safety device by limit switch to protect from over traverse.
-
Product
For Dielectric Oil Test
Stoil Cell
-
The option allows the testing of the insulation characteristics of the oil by checking if there is no contamination.
-
Product
Loss Tangent M in Dielectric Oil
TAND220A
-
The measuring instrument type TAND220A complies with the international standard IEC 61620. The instrument is based on the so-called "low-amplitude, low-frequency alternating current square wave method" and allows accurate measurements of conductivity and relative permittivity. Conductivity measurement in the range of 0.01 pS/m to 20,000 pS/m allows the use of this instrument for quality control of high resistivity liquids even at room temperature. The TAND220A works with a low test voltage and also with a low test current so that it does not represent a danger for the operators.
-
Product
Liquid Dielectric Test Cell
LT-4123
-
The LT-4123 Liquid Dielectric Test Cell is designed for testing the quality of materials such as the insulating oils used in transformers and the resins used in the manufacture of thermosets. With the LT-4123 Liquid Dielectric Test Cell, users can measure the AC loss characteristics and permittivity of liquids. The data gleaned from these measurements are used to set quality benchmarks for fluids during testing and manufacturing.
-
Product
Portable System for High-Voltage Solid Dielectrics Testing
HVT-70/50
-
Portable system HVT-70/50 is designed for carrying out high-voltage withstand testing of cable insulation and other solid dielectrics with DC (rectified) voltage up to 70 kV and AC voltage up to 50 kV RMS at industrial frequency (f = 50 Hz).
-
Product
Pressley Fiber Bundle Strength Tester
F215
-
To determine the tensile strength of natural fibers. Includes 1 pair clamps and spacer, torque vice and wrench, cutter, comb and tweezers. A 5mg x 0.01mg capacity balance is required but not included.
-
Product
Microwave Dielectric Measurement Systems
-
This system enables fast and non-destructive measurements of materials having various shapes, including thin films. Enables fast and non-destructive measurement of permittivity of thin-films and various dielectric materials using the evanescent mode of an open coaxial resonator.
-
Product
Dry Dielectric RF Coaxial Loads
4000 Series
-
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
Product
Bursting Strength Tester
-
TESTEX Testing Equipment Systems Ltd.
Bursting Strength Tester is used to test the strength of bursting for fabric. When you do bursting test, mullen burst tester is a wise machine for you.
-
Product
Broadband Dielectric Spectroscopy
-
Material Sensing & Instrumentation
Broadband Dielectric Spectroscopy is a powerful tool for investigating a variety of dielectric processes for both electrical and non-electrical applications. Also called Impedance Spectroscopy, the measurement separates molecular process on the basis of response time, providing a unique relaxation frequency along with a signature variation with frequency.
-
Product
DIELECTRIC and CONTINUITY TESTERS ( HI-POTS )
AV-25V-GC1-05
-
This tester is designed for testing equipment wiht a line cord which can be plugged directly to the tester. The continuity test is to determine whether the ground wire of the line-cord is well connected to the metal frame of the unit under test.
-
Product
Dielectric Insulation Analyzer
DIRANA
-
DIRANA uses dielectric frequency response (DFR) analysis in order to determine the condition of high-voltage insulation systems such as those in power transformers, bushings, cables and generators.
-
Product
Strength And Hardness Testing
-
Strength measures how much stress can be applied to an element before it deforms permanently or fractures. Hardness measures a material's resistance to surface deformation.
-
Product
Terminal Mechanical Strength Test
-
The terminal strength test is used to performed to determine whether the design of electrical terminals and their method of attachment can withstand mechanical stresses to which they will be subjected during installation or disassembly in equipment. These stresses must be withstood by the component without sustaining damage which would affect either the integrity of the terminals or the operation of the component part itself. Procedures are established in this method for testing, for example wire-lead terminals, flexible-flat-strip or tab-lead terminals, and rigid-type terminals which are threaded or have other arrangements for attaching conductors. The forces applied during the test consist of direct axial, radial or tension pulls, twist, bending torsion, and the torque exerted by the application of nuts or screws on threaded terminals.
-
Product
Dielectric Resonator Oscillators
-
Dielectric resonator oscillators (DRO) are free running oscillators that utilize state-of-the-art planar circuits, three-terminal devices and dielectric resonator technology to generate high-quality microwave signals with excellent frequency stability. In addition, these oscillators are equipped with an internal voltage regulator that further improves the frequency stability by isolating the external bias pushing and modulation. In general, these oscillators are fixed. However, a small mechanical or electrical tuning range can be achieved by use of a self-locking screw or an integrated Varactor diode. The standard offering covers the frequency range of 2 to 40 GHz. While standard models are equipped with female SMA and K connectors at the RF port, other RF interface options are also available.
-
Product
Peel Strength Testers
-
Peel Strength Tester can be used for peeling, stripping and other performance tests of adhesives, adhesive tapes, pressure sensitive tapes, medical adhesive bandages, protection films, release paper, laminated films, leather, woven bags and paper.
-
Product
EMF/ RF Field Strength Meter
-
Designed for measuring and monitoring Radio–Frequency electromagnetic field strength.
-
Product
Sliding Peel Strength Tester
OST3000
-
Compared to the scratch test, the friction and wear test is considered to be a durability evaluation method that is closer to the actual situation
-
Product
Digital TV Field Strength Meter
TM981 Series
-
TM981 digital/analog signal measurement. can measure digital average powe.
-
Product
Universal Material Testing Machine Tensile Compressive Fatigue Strength
Vexus MT20
-
Sinowon Innovation Metrology Manufacture Ltd.
Vexus MT20 series of material testing machine is designed in double-column with maximum testing force 20KN, it is able to make the material testing about tensile, compression, bending, shearing, bonding strength, peeling, tearing, etc, it is applied to test the material such as rubber, plastic, leather, metal, nylon line, fabric, paper, aviation, packaging, construction, petrifaction, electrician, vehicle and other materials.
-
Product
Strength Testing of Concrete, Brick and Mortar
Windsor Pin System
-
Measures the compressive strength of concrete, mortar and brick in-situ, quickly, accurately. A non-explosive instrument, the Windsor Pin System uses a spring-loaded device to drive a steel pin into the concrete or mortar.
-
Product
Broadband Isotropic Field Strength Probes
PI-01, PI-01E, PI-03, PI-05
-
Modern design probes meeting the requirements of most EMC and RF safety standards for RF safety, industrial, military and radar communication applications: 0.2-1000 V/m, 10 KHz-40 GHz.
-
Product
High Speed Dielectric Cure Monitor
LTF-631
-
The LTF-631 High Speed Dielectric Cure Monitor is designed for the study of rapidly reacting materials in research and development, quality assurance/quality control, and manufacturing applications involving thermoset materials such as resins, composites, paints, and coatings.
-
Product
LANDTEK Digital Muscle Dynamometer Muscle Strength Tester FM-204M50KG
FM-204M50KG
-
Guangzhou Landtek Instruments Co. Ltd.
LANDTEK Digital Muscle Dynamometer Muscle Strength Tester FM-204M50KGApplications:Making job task analysis and ergonomic analysis simple and accurate, it is ideal for workplace design, strength assessment and ergonomic research.Details:Force Rang:±50kgf,±490N,±110LbfResolution:0.01kgf,0.1N,0.1LbfAccuracy:±0.5%FS ± 1DigitUnit:kgf, gf, N, LbfMeasurement State:Peak Value Measurement, Real Time MeasurementDisplay:2 Reversed 4 Digit LCDPower Off:10 Minutes Auto Power Off, Manual Power OffBacklight:BacklightSafe Load:150%FS (Buzzer Alarm Over 110%FS)Power Supply:2x1.5 AA(UM-3) Battery or 5VDC Power SupplyOperating:0°C~40°CConditions:< 80%Surrounding:No Vibration Source or Corrosive Medium AroundWeight:705 gSize:host machine:170mm*72mm*35mmhandspike:315mm*Φ30mm Instrument stents：155mm*95mm*35mmAccessories:Standard Accessories:ManualCarrying CaseInstrument stents4 M3*18 screwsE-1005Optional Accessories:External USB power supply cableE-1004For quotation please feel free to contact Lisa Li. Thank you.
-
Product
Transformer Insulating Oil Dielectric Tester
CXYJ-501
-
Shenzhen Chuangxin Instruments Co., Ltd.
Insulating Oil Tester is designed according to of GB-86 and IEC60156 standards.
-
Product
Dielectric Assessment Kit
DAK
-
Schmid & Partner Engineering AG
The Dielectric Assessment Kit (DAK) is ideal for all applications where high-precision dielectric parameter measurements (permittivity, conductivity, loss tangent) are required, including applications in the electronic, chemical, food, and medical industries. The dielectric probes are designed for fast, precise, non-destructive, and user-friendly measurements of liquids, solids and semi-solids over the 10 MHz – 67 GHz frequency range.
-
Product
Dielectric Material Test Fixture
16453A
Test Fixture
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
Product
Testing Tensile Strength of Overlays, and Overlayments
James Bond Test ™ MK III
-
The James Pull Off Adhesion/Bond Tester measures the pull force used to pull a 2? or 3? disc away from the material being tested. This pressure is displayed on a precision gauge and can be related directly to the strength of the adhesion to the surface being tested.
