Humidity
-
Product
Glass Door Humidity Chambers
FW30
-
The Bemco FW30, mechanically cooled, Glass Door Humidity Chamber has a temperature range of -18 C to +94 C (0 F to 200 F) and a humidity range of up to 5% RH to 95% RH. This chamber features dry air injection and a direct humidity sensor. It operates without dewpoint limit from 5% RH to 95% RH over the range of 30 C to 85 C and even allows operation at 20% RH at 5 C and 50% RH at -14 C!
-
Product
Indoor Air Quality Meter CO, CO2, Temp, RH%
AQM4
-
UEi Test & Measurement Instruments
Four measurements in one instrument; carbon monoxide (CO), carbon dioxide (CO2), temperature and relative humidity. Use calculated 8 hour Time Weighted Average (TWA) and 15 minute short term exposure limits of CO2 for compliance testing and CO measurements for safety testing. Record, recall or download all readings to personal computer for later analysis or record keeping.
-
Product
Handheld Emission Particle Counter
HEPAC
-
Naneos Particle Solutions gmbh
Exhaust gas contains a lot of humidity, which can condense in the measuring device when the gas cools down. This could lead to problems with the measurement. Therefore, corresponding sensors are heated or the gas gets previously diluted. Exhaust gases from petrol and natural gas vehicles, however, contain a lot more humidity, which is why the device should only be used for diesel exhaust gases.
-
Product
USB Data Loggers With Graphics Screen
EL GFX
-
The EL-GFX range of USB Data Loggers feature a graphics screen. Different products feature a range of input types as well as temperature and humidity sensors. Users can quickly set up the data logger and view downloaded data by connecting the device to a PC.
-
Product
Portable Pinhole Detector
DZK-18
-
Shanghai Dean Electrical Co., Ltd
Online testing mode: round wireΦ0.05 -Φ5.0, flat wire B side Φ 3 - Φ 18Hand detection mode: round line diameter is not required, flat line width is not requiredTest length: 0-999 m to infinity (set by user)Detection speed: set by the userDefect short circuit current: 25±5uAResponse time: 5 ±1msWorking environment:0-40℃Relative humidity: 75% or lessOperating voltage: AC220V±5%Power consumption: <20W
-
Product
Compressed Air RH+T+Tdp Sensor
T3111P-2
-
Relative humidity, temperature sensors at probe on the cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Thermometer Hygrometer Barometer
H7530
-
Sensor H7530 is designed for online monitoring of temperature, relative humidity of air without aggressive substances. Three binary inputs to detection of two-states signals are the advantage. Other devices are controlled by two relay outputs.
-
Product
Thermometer and Hygrometer
WS200-1
-
Advance Plus Trading Co., Ltd.
Model Number: WS200-1 Key Specifications/Special Features: Specifications:Indoor temperature range: -30-50℃ (-22-122℉)Outdoor temperature range: -50-70℃(-58-158℉)Instant read out of temperature (selects indoor or outdoor) and humidity3m external temperature sensorAccuracy of±1℃ between operating temperature of 0 to 50℃℃/℉ selectableMinimum/maximum temperature and humidity memory recallOperated by a LR03 AAA 1.5V battery
-
Product
Water Vapor Sorption Analyzer
DVS Adventure
-
DVS Adventure is a water vapor sorption analyzer that measures sorption and desorption isotherms over a broad range of humidities and temperatures. It offers unprecedented temperature stability and humidity performance.
-
Product
Wireless Thermometer
-
Offers convenient and reliable digital thermometer and humidity readings in multiple locations.
-
Product
Constant Temperature Humidity Battery Test Chamber
-
Guangdong Test EQ Equipment co., Ltd.
- Battery-Specific Thermal Management: Dual-compressor cascade cooling (-40°C stability) and ceramic heaters for rapid high-temperature recovery.- Precision Electrochemical Control: Integrated battery cyclers with CAN/Modbus protocols, supporting SOP (State of Power), SOH (State of Health), and DCR (Direct Current Resistance) monitoring.- Safety-Centric Design-meet Hazard Level: Chambers are designed with Fire-resistant stainless steel interior, fire suppression,nitrogen purge system, and emergency power cutoff for thermal runaway prevention .- Data Acquisition & AI Analytics: Real-time logging of voltage, current, temperature, and pressure via LabVIEW/Python APIs. AI-driven anomaly detection reduces test cycles by 30%.- Energy Efficiency and Energy Storage: Heat recovery during discharge cycles cuts energy use by 25% (ISO 50001 compliant).
-
Product
Temperature, Humidity, Bar. Pressure Transmitter
T7318
-
For exacting interiors in building energy management and HVAC systems. Are designed for easy installation on ordinary KU68 wiring boxes for household switches and sockets.
-
Product
Reach-In Conditioning Test Chamber
-
Weiber Conditioning Test Chamber Manufacturers offers an ideal apparatus for conditioning materials at non-ambient temperatures. Now researchers, engineers, and technicians have a simple and cost effective method to condition samples prior to testing. Laboratory Conditioning Chamber is designed for the conditioning of samples prior to testing, provides conditions from 20% to 98% RH ± 2 and 0°C to 94°C ± 0.5°C.Conditioning Test Chambers offers ideal humidity and temperature conditions required for testing the effect of environmental changes on the product. The chamber can be widely used to evaluate the durability of various products. Weiber delivers customized products at the most economical rate and within the limited delivery period.
-
Product
HVAC Tools
-
From simple, one-time checks to advanced wireless instruments to measure temperature, humidity and airflow or check for gas leaks, turn to Amprobe for a complete line of tools designed specifically for HVAC.
-
Product
Transducer with RS232 Interface
-
RS232 transducers / transmitters for temperature, humidity, atmospheric pressure and CO2.
-
Product
CompactPCI 3U Module
CPCI-1553-DDC
Controller
Operating temperatureCommercial: 0 to +55 °COptional: -25°C to +80°C• Non-operating: -40°C to 85 °C• Airflow requirement: .5 CFM• Humidity: 5 to 90% (non-cond.)• Altitude: 0 to 10’000 ft
-
Product
Portable Humidity Calibration Case
Hygro-box
-
Hygro-box is a easy-to-use, portable, IP68 humidity calibration case, suitable for outdoor or moving application.
-
Product
Humidity Meter, 0% to 100% Relative Humidity, 5 %, 0.1 °C, 55 mm, 32 mm, 10 mm
72-9190
-
This combination thermometer/hygrometer provides accurate, instant readings of ambient environment and handheld size easily fits in your pocket
-
Product
Testing Released Water Vapor
Humiditest™ Complete System
-
The James Instruments Humitest System allows the concrete practitioner to monitor and ensure that a new structure is dry enough to proceed with the next phase of construction. This is especially critical for concrete structures requiring a coating, carpeting or similar floor or covering treatment. Installing such treatments before the concrete is sufficiently dry will typically cause expensive failures in the covering treatment. The only accurate way to ensure that the concrete is sufficiently dry enough to safely avoid expensive re-work is via a bore hole humidity test system, such as the Humitest System
-
Product
Vibration Chambers
ETV-SERIES
-
Environmental Chamber with Vibration Shaker Interface provision consists of Environmental Test Chamber, Vibration Shaker Interface Provision, HMI/PC PLC based Control System etc., This chamber is designed with unique features to meet the control parameters like Temperature, Humidity (optional) and 3 Axis Vibration Controls which are specified in the specification.
-
Product
Walk-In Temperature & Humidity Test Chamber
-
Weiber walk in humidity test chambers are conceptualized and designed to create test chambers to study and contemplate the effects of different environmental parameters such as humidity, temperature applications tests involving micro-organisms, plants, tissues, electronic components etc. apart from various customized industrial and research applications. Our humidity test chambers have a variety of usage in R and D laboratories, research studies and product testing facilities across the globe. Apart from that, these chambers have a variety of usages in tissue culture applications, enzyme reaction studies, growth observation studies, fermentation analysis and various other general and specialized applications in various laboratories. We specialize in both standard and customized humidity test cabinets, specifically designed to meet the challenging demands of various scientists for individual and specialized research applications.
-
Product
Environmental/Stability Chambers
-
Canden offers unique- Dual environment chamber-This model allows users to set different temperature, humidity setting in 2 sections with in the same chamber divided by a common wall.
-
Product
Humidity and Temperature
Hygropin humidity concrete ASTM F2170
-
The Hygropin moisture meter offers the perfect solution to identify and monitor moisture in concrete. Due to the small and fast sensor of the moisture meter, diagnosing moisture according to ASTM F2170-09 is quicker and easier than ever before. The relative humidity test requires placing a measuring sleeve at a specific depth. This can be done either by drilling a hole or by pre-installing cast holes in fresh concrete. This moisture meter provides the smallest available sensor on the market, minimizing damage to the surface and reducing the installation efforts immensely.
-
Product
temperature, humidity, bar. pressure transmitter
T7410
-
Built-in relative humidity, temperature, atmospheric pressure sensors. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Web Sensor
T3511P
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Air Humidity Meter
-
Since air humidity is an important factor in many sectors including but not limited to manufacturing, agriculture, construction, restoration, remediation and heating, ventilation and air conditioning (HVAC), PCE also carries a number of air humidity meter devices designed for specific applications such as evaluating heat stress risk in hot work environments like boiler rooms, factories, construction sites and commercial bakeries. To accurately assess heat stress risk, an air humidity meter capable of detecting and classifying temperature in relation to the amount of moisture content in the air is recommended. The global standard description for heat stress is the Wet Bulb Globe Temperature Index (WBGT).
-
Product
Humidity and Temperature Transmitter
T3111Ex-2
-
Relative humidity, temperature sensors at probe on the cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Thermometer Hygrometer
H3530
-
Sensor H3530 is designed for online monitoring of temperature, relative humidity of air without aggressive substances. Three binary inputs to detection of two-states signals are the advantage. Other devices are controlled by two relay outputs.
-
Product
USB Wall Mount Temperature Datalogger
VA600-N1/VA600-N/VA600-NH95
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Temperature humidity data logger with USB, widely used in cold -chain transportation field HVAC refrigerator field.
-
Product
Web Sensor with PoE
T7611-4
-
Ambient temperature, relative humidity, atmospheric pressure t-line Web sensor with Power over Ethernet feature. Remote alarm.
