Control
Known value
-
product
PXIe Remote Control Interface Module with Daisy-Chain Facility
43-921-001
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling.
-
product
PCIe to PXI Remote Control Interface Kit
41-924-001-KIT
The kit is supplied with a PCIe card which can plug into any PC PCIe slot, a PXI module for insertion into Slot 1 of a PXI chassis and 3m lead to connect the two parts together. The interface uses a single lane PCIe connection from the PC to provide a software transparent link from the PC PCIe backplane to the PXI backplane. The supplied 3m shielded lead ensures the system has robust operation and an adequate separation distance between the PC and the PXI chassis.
-
product
Process Control Instruments
Sensors to measure process conditions and valves to influence process operations are essential for all aspects of engineering practice. Engineers want to design and operate processes that remain in safe conditions, produce the desired amounts of high quality products and are profitable. Therefore, engineers must provide measuring devices for key variables and valves (or other devices, such as variable speed electric motors) to influence of “steer” the process. This site provides educational material on sensors and valves for use in the process industries.
-
product
PXI-8368, MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module
783934-01
MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module—The PXI‑8368 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCI‑8366 through a copper, x1 MXI‑Express cable. The fiber-optic cabling of the PXI‑8368 provides electrical isolation between the PC and PXI chassis, as well as cabling up to 200 m per link.
-
product
Chassis - Control Relays Greater than 8x1 or Control Multiple Relays in Series Forming Larger Switches than Normally Possible Such as 16x1 to 32x1 Sections.
CXM/256-MF
These Chassis are typically used to control relays greater than 8x1 or control multiple relays in series forming larger switches than normally possible such as 16x1 to 32x1 sections. Or control mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 256 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional.
-
product
PXI GPIB Instrument Control Module
PXI GPIB Instrument Control Modules feature IEEE 488 controllers for PXI systems. You can choose an option that supports Gigabit Ethernet transfer speeds. PXI GPIB Instrument Control Modules include a license for the industry standard NI-488.2 driver software enabling reliable connections to third-party instruments with GPIB.
-
product
All-in-one Streamer Positioning & Control
Nautilus®
Nautilus provides positioning as well as vertical and lateral steering in a unique node. Fully integrated with Sentinel, Nautilus is directly powered from the streamer providing a greater availability and enhanced safety with reduced number of workboat operations.
-
product
Analog Control Cable for Electronic Loads
EE105T-xx
The EE105T pre-wired bias power cable is designed to be used with the EE301xx & EE151xx series electronic loads. The cable allows you to connect the electronic load to a regulated 12Vdc bias power supply for operation of the electronic circuits in the load or by moving a wire use the 15-24 Volts unregulated input
-
product
Scienlab Measurement And Control Module
SL1067B
The Measurement & Control Module SL1067B is a rack-mount measurement module for measuring voltage input ±10 V with 16 channels. The module can be used either as a stand-alone device or as extension for a Scienlab Battery Test System.
-
product
Probes & Meters To Monitor & Control PH/ORP
Digital and analog, combination probes, differential probes, mounting hardware and accessories.
-
product
Control Board for Motor, Pump & Valve
F1V04
Beijing SANKI Petroleum Technology Co., Ltd.
The main board issues a start signal and a low voltage signal (12v) for opening the electromagnetic valve, which are converted into strong voltage signals (220 VAC) to drive the electromagnetic valve (380 VAC) and the motor in our fuel dispensers system, thus completing the function of conversion from weak voltage power to strong voltage power. The control board circuit isolates high voltage interference signals via photoelectrical isolating components.
-
product
Pressure Control Machine
EQ-6V / EQ-12V
The constant pressure device enables the stable supply of materials to the stuffing machine by keeping constant the pressure to the materials in the pipe fed from the pump to the stuffing machine side by air pressure. When the materials being fed from the pump, the surplus materials unnecessary to be stuffed shall be sent into the constant pressure cylinder. And when the constant pressure cylinder is full, the supply from the pump shall be stopped and then the materials in the cylinder shall be discharged into the pipe by constant pressure. Accordingly, it is unnecessary to synchronize the stuffing speed with the pump speed by every product. Also, the pressure shortagegenerated when the pump motor starts and the effect of pressure fluctuation in the pipe due to the changes of the speeds of the pump motor and stuffing machine can be minimized so that it is possible to supply stably the materials to plural stuffing machines.
-
product
Hydraulic Servo Control Compression Testing Machine (Four Column)
TYE Series
Jinan Testing Equipment IE Corporation
This series Servo-Hydraulic Compression Testing Machine is mainly designed for compression test of building material items, such as concrete cubes, cement specimen, paver materials and related component, etc. With new design idea and advanced technolog, this series has more advantages in appearance, operation & applications. The compression testing machine is an ideal tester for quality control at industrial & mineral enterprises, teaching in high schools, and technology researching at scientific institutes.
-
product
Scienlab Measurement And Control Module
SL1066B
The Measurement and Control Module SL1066B is a rack-mount measuring and control module that provides adjustable voltage outputs for BMS and DUT power supply and floating relay contacts to simulate e.g. vehicle specific terminals 15, 30 and 31.
-
product
Remote Control Voice Recognition Tester
BK3013
Ready to help you take on the leading edge of consumer technology, we have designed a machine that tests microphones which both use RF and are used for voice recognition. The BK3013 runs a uniform SPL sweep to calculate FRF and also runs an SPL sweep that allows you to test the SPL range of your mic. Our "Test Shop" program will show you the results in graphs and allows you to have the computer check specific points in the test.
-
product
PathWave BenchVue Advanced Power Control And Analysis For Multiple Instrument Connections
BV9200B
Control and analyze voltage and current measurements from multiple N6705C, N7900 or RP7900 Series
-
product
PCI, IEEE 488 GPIB Instrument Control Device for Windows, Low Profile
783007-01
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
product
Control Board For Testing PCBs
TCC 1800
The TCC1800 Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via a galvanically separated USB interface. The TCC1800 is designed to work with positive voltages up to 24V. All inputs and outputs are protected against higher voltages however. The card provides basic IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, Serial (UART) and I2C interfacing.
-
product
Digital Vibration Control System
DSC-98000MJ
The DCS-98000MJ series vibration control system is the most suitable digital vibration control system used for an electrodynamic vibration testing system to perform vibration evaluation test for highly advanced industrial products. The system is a highly stable Embedded Computer based system, the computer on which the Intel® Celeron™ Processor is installed. It consists of the vibration control, the communication Dynamic Control Unit (main DCU), and the expandable measuring input/output Dynamic Control Unit (sub DCU).
-
product
On / Off Control Of Temperature
ULP-28
Unitech Scales And Measurements Pvt. Ltd
Unitech on/off temperature control module through relay with present value and set value display.
-
product
Attenuation Control Unit, DC to 26.5 GHz, 0 to 101 dB, 1-dB Steps
J7201C
Designed for wireless communication and aerospace and defense applications in both R&D and manufacturing test.
-
product
Motion Control Board, PCI
APCI-8001-1
*Axis control for 1 servo or stepper motor*Onboard processor*Optical isolation*16-bit analog output channels*Direct connection of commercially available incremental encoders *or SSI absolute encoders
-
product
Demand Control
You can start saving money today with maximum demand control systems by Measurlogic. Our sophisticated demand control systems help property owners shed excess energy expenditures with lighting, air conditioners, ice machines, and more. We can help you build a plan for maximum energy savings.
-
product
Integrated Solution for Control and Automation
One
Building new machines for today’s smart factories requires sophisticated control and automation that can only be delivered through multiple solutions and components – including a PLC, HMI, I/Os and motion components such as AC Servo systems and VFDs. As all components must be integrated, selecting the right combination is crucial to the efficiency and success of any project.
-
product
Control Electronics
Data acquisition and control electronics for optical radiation sources and measurement systems including precision current and voltage supplies for LEDs and tungsten halogen lamps.
-
product
Ku Band Gain Control Amplifier
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
product
PCI-GPIB+, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device for Windows, Onboard GPIB Analyzer
778033-01
The PCI‑GPIB+ combines an IEEE 488 controller and an analyzer on one device for computers with PCI slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The PCI‑GPIB+ achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Machine Vision System for Magnetic Luminescent Control of Wheels
The machine vision system of the wheel magnetoluminescent control unit is designed to automate the technological operation of the magnetic luminescent control in the production of railway wheels with full-profile mechanical surface treatment. The system is a hardware and software complex for presenting complete information on the tested wheel to a flaw detector operator, automatic detection of potential defects, maintaining a control protocol and interacting with the installation controller and the line database.
-
product
BenchMate Active Air Vibration Control
2212 Series
BenchMate Vibration-Free Platforms enhance the performance of precision tabletop equipment.The 2212 Series is an Active-Air design that requires a source of compressed air (not included). It is a self-leveling unit and recommended for regular use.
-
product
Noise Control And Acoustical Consulting Services
Our acoustical consultants use the latest and most advanced noise prediction and modeling software, precision sound measurement equipment and detailed acoustical analysis that enable us to help our clients achieve their project's noise requirements and goals. Contact us before your noise challenges become noise pollution problems.
