Timing
See Also: Time, Timers, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Time Interval Analyzers
-
Product
Conditioners and Transmitters
-
DIN rail mounted micro-controller based analogue load cell transmitters. They have very high accuracy and long term stability with advanced design.Using an up to-date delta-sigma ADC and 16 bit DAC to achieve higher speed and accuracy these instruments give the system designers a lot of advantages towards increasing system reliability and reducing the installation and service times. All instruments' analogue outputs are matched during production to simplify calibration with a PLC and to simplify exchanging the instrument without recalibration in service when initial adjustment has been performed in the PLC.
-
Product
Carton Crease Proofer
CCP
-
The Hanatek Carton Crease Proofer (CCP) allows the user to produce production quality crease samples without committing valuable machine time. The instrument can assist in checking ink and coating flexibility. The CCP comes complete with commercially produced rules and dies which are identical to those used on a full sized cut and crease machine.
-
Product
Digital Oscilloscope
MOSTs5
-
MOSTS5 is designed to convert instantaneous voltage values of an electrical signal into a digital code, measure instantaneous voltage values, measure time intervals between two instantaneous voltage values through two independent galvanic isolation channels.MOSC5, according to the conditions of use, meets the requirements for measuring instruments of group 3 in accordance with GOST 22261-94.
-
Product
8G + 2G SFP Managed TSN Switch
EKI-8510G-2FI
-
CC-Link IE TSN Class B Certified, 8 x Gigabit ports + 2 x Gigabit SFP ports, IEEE 1588v2 PTP Precision Time Protocol. Features IEEE 802.1AS Time Synchronization, IEEE 802.1Qbu Frame Preemption, IEEE 802.1Qbv Time Aware Shaper and IEEE 802.1CB Seamless Redundancy.
-
Product
Halt Hass Chambers
-
HALT and HASS chambers from WEIBER provide extreme temperature & vibration capabilities used during the product design and manufacturing cycles to compress the time normally required to identify design and process weaknesses. HALT techniques are important in uncovering many of the weak links inherent to the design and fabrication process of a new product. HASS techniques are incorporated during the production phase to find manufacturing process defects that could cause product failures in the field.
-
Product
Website Monitoring
-
Keep a close eye on the performance and availability of your web pages with HTTP monitoring & HTTPS monitoring. Check if the web pages on your web application are reachable or not. When they are not reachable, get alerts and notifications & remedy actions follows. The website monitoring feature looks for various critical attributes such as the page response time. Set up a URL for monitoring & then define a threshold – if the webpage load time is more than 10 seconds, you should receive SMS or an e-mail. Active notifications help IT admins in taking quick corrective action before its unavailability affects end users. It also lets you make sure that CGI scripts, web server and back-end databases are performing properly.
-
Product
3-Lambda Power Meter
3λ-PM
-
•Simultaneous wavelength detection and calibration.•B / E / G – PON 3 wavelength power meter and insertion loss tester (1310 / 1490 / 1550 nm)•Simultaneous measurement of 3-wavelength PON signals•Automatic wavelength detection to save time and cost•Rugged, shock and water-proof for field use•Compact, lightweight and cost-effective•Quick and easy to operate
-
Product
Relaying Protection Tester
GDJB-III
-
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1. DC voltage relay test2. DC current relay test3. AC voltage relay test4. AC current relay test5. High current injection6 Time counter in relay test
-
Product
Snubber Capacitor
STP-01R
-
We can customize Snubber Capacitor as Box or Epoxy Dipped type, and support other parameters requirement.Different applications can have very different capacitor electrical and mechanical profile requirements.Please feel free to send your application details; we might have a solution for your need.Production Lead Time will be about 30 - 50 days, depending on order quantity, material and production status.
-
Product
Benchtop Non-Contact Directional Geometry Spectrophotometers
-
Hunter Associates Laboratory, Inc.
Unique measurement methods that don’t require instrument contact with your samples. These benchtop spectrophotometers are perfect for samples that are not smooth, uniform or are messy. These solutions reduce sample preparation time and cleanup time while ensuring absolute measurement accuracy and consistency.
-
Product
Loading Devices
-
Educated Design & Development, Inc.
Sometimes you may need additional loading for abnormal testing (i.e. overload test). Other times, you may need additional loading to simulate worst case normal operation conditions (i.e. input test, temperature test). No matter what your application, we have the loading device to fit your needs! TECH NOTE: Be sure to request our outline titled "Selecting Loads" for assistance in determining the proper rated device for your application.
-
Product
Transforming Analog Circuit Breaker Testers
MAC-21
-
The MAC-21 uses proven microprocessor and A/D converter technology to provide real-time waveform analysis. This ensures accurate true-RMS readings of current pulses, even with DC offset and distortion, which are typical in primary injection testing. Intelligent threshold algorithms provide accurate trip time measurement. Integration of measurement and control functions allow advanced features such as preset on times, auto ranging, and optional printer or computer interface.
-
Product
High Voltage Isolator for Logic Analyzers
LX-08
-
The LX-08 series of high voltage logic analyzer adapters provides a safe isolated method of measuring high voltage control signals with a low voltage logic analyzer. All inbound signals are optically isolated and attenuated to a safe level for the delicate inputs typically found on logic analyzers. The inputs on the LX-08 are capable of withstanding voltages up to +/- 300V AC/DC, higher voltage configurations are available upon request. Rather than probing with multiple neon screwdrivers, the LX-08 can provide simultaneous viewing of up to 8 circuits in the STANDALONE mode via the indicator array. Need to catch a transient event or map out a timing sequence? Just add a logic analyzer to the outputs of the LX-08 and turn it into a high voltage logic analyzer. High voltage signals that were hazardous for a logic analyzer can now be measured safely. Typical outputs of a high speed PLC sequencer can be precisely timed and measured from both sides of the control relay. With the built in user selectable AC filter circuit, an AC signal can be measured as DC events or AC cycles.
-
Product
Rectal Probe For Mice
RET-3
-
• Smooth ball tip. Stainless steel shaft - 3/4'' long, .028'' diameter. Tip diameter .065'', 5 foot lead length. Time constant 0.5 seconds. Not Isolated
-
Product
Imaging
SLA64 (Preliminary)
-
A 1 x 64 element silicon-based thermopile array. Each active area is 0.45mm x 2.0mm with a time constant of 42ms and a low Temperature Coefficient of Responsivity of -0.06%/C. It is packaged in a 68-pin QIP. Includes internal 30k 5% NTC chip thermistor provides ambient package temperature measurement. See Thermistor Options p/n: MT04.
-
Product
C/Ku Band Satellite Monitoring
SCL-3412
-
C/Ku Satellite Monitoring System (SCL-3412) is designed to intercept International/national telecom carriers, GSM A/Abis links and IP Carriers over satellite which are using C, Ku, X or Ka-Band. In order to reduce the manual effort and time consumed in the analysis of the carriers, system is integrated with Satellite Carrier Analysis module, which automatically performs the scanning on the selected spectrum and provide the list of carriers along with their payload type (i.e DCME, GSM or IP) and characteristics parameters. This provides great help to take decision for monitoring of the carriers of interest.
-
Product
Inline Fitting
-
The modular concept of process inline fitting allows adaptation to virtually every process. Replacement of components or expansion is possible at any time.
-
Product
General Purpose Probes
PIT-12
-
PIT-12 General Purpose Probe for Pressurized Systems - 12'' #304 stainless steel shaft. Diameter is 1/16''. Immersible. Maximum temperature 350°C, Time constant 0.5 Seconds. Shaft Terminated in a sub-miniature Type T Thermocouple plug. 10 foot Sub Miniature Type T extension lead supplied. Not isolated.
-
Product
Automotive Ethernet Tx Test Software 10M To 10Gbp
AE6920T
-
Unlike CAN, LIN, Automotive Ethernet demands rigorous compliance verification using test cases that cover transmitters (Tx), receivers (Rx), and harness/connector assemblies. To help you save time and effort, Keysight offers solutions that automate the testing and validation across Transmitter (Tx), Receiver (Rx), and the connections between Automotive Ethernet devices. Our engineers have invested thousands of hours in learning the standards and creating automated, repeatable compliance tests. These proven applications help you ensure proper test configuration and valid measurement results. Ultimately, you’ll have greater confidence that your device is compliant. Now available for data rates up to 10Gbps. The automotive Ethernet test solution AE6900T offers hardware and accessories to make sure you have all of the components you need to get up and running quickly.
-
Product
Simulate millions of real-world end-user environments
PerfectStorm
-
Keysight Network Applications and Security
The next generation of our well-received PerfectStorm 10/40GbE platform is available now. PerfectStorm 100GbE is the world's only native 100GbE testing platform, far ahead of other test solutions, the closest of which offers just 10GbE native interface support. The new platform comes to market at the right time, as equipment sales of 100GbE are ramping in Service Provider and Enteprise Data Center.
-
Product
TamoSoft® Throughput Test
-
TamoSoft Throughput Test is a utility for testing the performance of a wireless or wired network. This utility continuously sends TCP and UDP data streams across your network and computes important metrics, such as upstream and downstream throughput values, packet loss, and round-trip time, and displays the results in both numeric and chart formats. TamoSoft Throughput Test supports both IPv4 and IPv6 connections and allows the user to evaluate network performance depending on the Quality of Service (QoS) settings.
-
Product
Common Rail Injector Tester
ICR-4 Tester
-
ICR-4 tester is used to control electromagnetic and piezoelectric injectors used in the common rail injection systems. It is possible to control up to four injectors of a type at a time. The signal generated by the tester which controls the injectors, corresponds to the signal which appears in the car engine controller.
-
Product
PXI 3A Power MUX BRIC, 16-Channel, 6-Pole
40-571-402
-
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Time-Triggered Ethernet / ARINC 664 Part 7 (AFDX®) / IEEE 802.3 Ethernet Deterministic Communications
TE2
-
Module TE2 is one of NAI's latest generation of advanced function Configurable Open Systems Architecture™ (COSA®) compatible modules. The TE2 is a certifiable, single-port, tri-redundant, deterministic Ethernet communications interface module that supports TTTech’s certifiable TTEthernet® End System product consisting of three traffic classes: SAE AS6802 (Time-Triggered Ethernet), ARINC 664 Part 7 (Avionics Full-Duplex Switched Ethernet (AFDX®), and/or IEEE 802.3 best-effort protocol. By supporting all three traffic classes, NAI's TE2 is the ideal solution for current users of IEEE 802.3 Ethernet, who plan to upgrade to Deterministic Ethernet (ARINC 664 Part 7 (AFDX®) or Time-Triggered Ethernet SAE AS6802) protocols in the future at any time without changing hardware.
-
Product
Midi Time Code Reader
MTC
-
MTC - Midi Time Code hardware Analyzer or Analyser /Reader/Decoder. The MTC Decodes any (FX) System Common or System Real-Time Messages and displays them in a clock format, independent from your MTC generating device. The MTC has the same input and HOLD and SCROLL features as described in the MA1 module.
-
Product
Precision Current Sources
-
DC Precision Current Sources provides precise and very stable output currents from 3 A to 10,000 A. The 6623A-PCS Series provides the best uncertainties of any DC high current sources (i.e. < 5 ppm of precision and stability at 1000A). In addition this Series is modular and initial output currents can be expanded at any time.
-
Product
Multi-points Temperature Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
TP series of multiplex temperature meter is a kind of instrument which suits to real time monitor and trace multi-points temperature simultaneously. With the features of Simplified operation, high precision and reusable thermocouple, it is widely applied in electronic ballast, motor tools, lighting fixtures and household appliances. The application software records and save the temperature rising curve in real time for analyze purpose.
-
Product
Sound Level Datalogger
DSL 331
-
Auto Ranging Measurement 30dB to 130dB. Work with Window Software. 32,000 Records Data Logger. Bar graph Indication with Back Light. RS-232 Real Time Display Software for Window 95/98/2000
-
Product
Time Interval/Frequency Counter
SR620
-
Stanford Research Systems, Inc.
The SR620 measures time interval, frequency, pulse-width, rise and fall time, period, phase and events. Time intervals are measured with 25 ps rms resolution, making the SR620 one of the highest resolution counters available.
-
Product
Documenting Calibrators
-
We offer documenting calibrators, for us the “documenting” calibrator means a calibrator that can store the calibration results into its memory and upload them to calibration software. This benefits you as you don’t need to carry pen and paper and spend time in making notes and typing them into software.
