Filter Results By:
Products
Applications
Manufacturers
-
product
EV Power Components End of Line Test Platform
Test and Validate all EV Power Electronics with One Flexible and Scalable Solution
-
-
product
End of Line Noise Test System
End of Line Noise Test Systems from VIacoustics are designed to support end of line product noise testing on factory floors and quality assurance environments. Using the Limit Analysis features of the Nelson Acoustic Trident software, users can set noise emission maximum, minimum or control range criteria based on Awtd and/or 1/N octave band criteria. Criteria can be customized for most any type of product based on the noise emissions of known good and bad units. The large front panel Pass/Fail indicator allows operators to quickly determine if units meet the criteria. Data on units that fail can be exported for further analysis.
-
product
End of Line Test System for Automotive Seats
AS519
AS519 is specifically designed to perform ECU’s EOL tests in the automotive industry. It integrates a programmable power supply up to 20V 20A with high reading resolution. Interaction with the DUT is established through CAN bus by an interphase adapter in a USB port of the test managing computer.
-
product
Lumber Moisture Measurement Systems
Improved moisture control has emerged as an important process improvement element in the forest products industry as mills continue to focus on profitability and yield. SCS Forest Products by Finna Sensors provides the industry’s widest-used end-to-end line of integrated moisture measurement systems and related process optimization tools for the sawmill, kiln and planer.
-
product
Fast LID Measurements for EOL
KMP
TechnoTeam Bildverarbeitung GmbH
The KMP is the solution to cost-effectively bring indirect light measurement technology to places with too little space for a BV room. Its lightweight and compact design allow it to be integrated into production lines, positioned next to production or in a small lighting lab.
-
product
Multifunctional Safety Tests
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
product
Multi-Purpose Probes
*For All your Functional Test Needs *Machine Building *end of line test
-
product
Sound Harmonics and Current Analyzer
H74050100
This analyzer is used as end of line control for electro mechanic components with electric motors, with or without mechanical reduction. While the motor is running at nominal speed, a spectrum and temporal analysis of the sound as well as a current consumption test is performed. Statistical analysis of the data acquired is also performed real-time, expediting the PASS/FAIL decision of the DUT.
-
product
Testing Large Radar Sensors with CATR Technology
CATR Radar Test System UTP 5069
Modern driver assistance systems must recognize increasingly complex traffic scenarios and convert them into appropriate vehicle reactions with the help of artificial intelligence (AI) and specific algorithms. Imaging radar sensors with a higher spatial resolution, so-called imaging radar sensors, are therefore required. These can better distinguish larger from smaller objects and, due to the larger antenna apertures, also require larger dimensions of the test environment or larger far-field distances. Testing these sensors in the direct far field ( UTP 5065 ) would therefore require very large absorber chambers up to ten meters in size and more.Our efficient test system UTP 5069 offers exactly the right solution:By using CATR technology (Compact Antenna Test Range), 4D, imaging and other radar sensors with large far-field distances are calibrated with high precision in a small footprint. With the extremely low-reflection NOFFZ absorber chamber, the system is very well suited not only for validation, but also for EOL tests.
-
product
Install and Development
Whether it is an error proofing application or a complete end-of-line (EOL) test solution, ARC services what we sell by providing quality onsite installation and development as required by the project. Whether it is a senior engineering resource or our expert team of engineering technicians, ARC can provide the best solution to get your application up and running at your site when completed.
-
product
EOL Testing of Speed Sensors
Complete programming and end of measuring stations integrated in the assembly line for rotary electronic sensors with automatic sensor recognition.
-
product
Tooling And Fixturing
Control develops and supplies fixtures and test accessories :*For a vast field of applications - ICT (In-Circuit Test), functional test, Flash programming, EoL (End-of-Line) test systems, etc.*For all handling systems currently used in the market: online or offline, mechanical, pneumatic or vacuum operation*From simple mechanical fixtures, with a few hundred probes and low production volumes, to highly complex accessories with thousands of probes, double-sided probes, double acting, etc.
-
product
Inductor Test & Packaging Machine
1870D
The Chroma 1870D Series (1870D/1870D-12) are specifically Designed automated test equipment for chip inductors. It comprises Various test functions that are required for verifying chip inductors. In addition, an automated tape packaging machine at the end of production line is equipped to fulfill demand for automated manufacturing.
-
product
Protection System Tools
Megger’s comprehensive range of products for relay tests includes high current primary injection, relay phase angle, end to end line protection GPS timers and relay current amplifiers.
-
product
Automotive Battery Production Line Tester
The Production Line Tester (PLT) is typically installed at the end of battery production lines (finishing). An electrical load test after formation charging is essential to assure performance and quality. The energy discharged during this test must be minimized to eliminate the need for recharging after testing.
-
product
Transformer Tester
MOTOMEA Distribution Transformer Test Systems: Routine Testing for Production (EOL) and Quality Assurance (QA). Type Testing at Laboratory (R&D)
-
product
Sealed Beam Bulb Testing System
H710019SSL
EOL test for manufacturing of bulbs with LED for applications requiring to ensure watertightness: vehicles, marine, swimming pools, operating rooms, classified areas (Ex Zone), etc. The test system checks in a short time all the light and electrical characteristics of the bulb. A high precision Micro Leakage Meter also checks that there are no leaks between the environment and the inside of the bulb. The test results are recorded on the PC and can be printed on a quality control label attached to each unit.
-
product
Series and EOL Testing of Electric Motors
Highly automated EOL test system for blind motors*Test station with fully automatic mechanical and electrical contacting *Scanning the product coding with barcode scanner*Integrated label printing, additional error printer*Contact protection by light curtain
-
product
CATx Surge Protector
SP-CAT5-6V
Protects sensors running on CATx unshielded twisted pair (UTP) cable against the effects of electrostatic discharge, faulty wiring and lightning. The use of two protectors on each end of the line will provide increased protection for each end against surges. Protected pins: (1,2) (3,6) (4,7) and (7,8) pass through. Impedance: 85 to 115 Ohms. Surge suppression: 22Vpeak @ 100A 10/1000µs. Maximum continuous voltage: 6Vpeak. Dimensions WxDxH: 1x3.6x0.9 in (25x91x23 mm). Regulatory approvals: GR 1089, NEC 800.100 and 830.100, ITU 703, UL94 V0 Flame Rated.
-
product
Automated Test Handler
In-Line Duomax
100 % Automated Fixture Change1.5 N x 8000 Test PointsICT FCT EOL IntegrationHigh ProductivityHigh QualityGreat ROINo PLC
-
product
Multi-Spectral Test Set
MSTS
The Multi-Spectral Test Set (MSTS™) is a two-color infrared (IR), ultra-violet (UV), and multi-band laser hand-held test set with an integrated detector. The MSTS provides an end-to-end flight line confidence test for directional infrared countermeasure (DIRCM), UV missile warning systems, IR missile warning systems, and multi-band laser warning systems. The MSTS is ruggedized, battery-operated, and can be hand-held or mounted on a tripod.
-
product
Systems Analysis Interface
Saint2
The Systems Analysis INterface Tool 2, a Delphi Preferred Tool, for Low-cost EOL Testing & Reflashing Without the Need of Additional Hardware.
-
product
EOL Tester
Sterner Automation would like to introduce its new end of line (EOL) tester platform. Sterner Automation has been a supplier of calibration and test equipment to the automotive industry for over a decade and is now offering a standard hardware EOL platform that is configurable with a variety of software modules for seating plant applications.
-
product
EOL Testing of Starter-Generator Units (ISG)
Series test rig for starter-generator units (ISG)*High voltage test*Insulation resistance measurement*Temperature sensor control*Short circuit test*EMF test*Performance measurement*Manual loading and contacting
-
product
Radome Tester
QAR50
The R&S®QAR50 is the ideal tool for accurately testing the quality of automotive radomes and bumpers in the automotive radar frequency range at the end-of-line (EOL). It features sufficient space to easily accommodate bulky bumpers combined with spatially resolved measurements to evaluate the homogeneity of design emblems.
-
product
Function Tester with Low Number of Channels
UTP 6010 RF
The UTP 6010 is one of our smallest test systems and therefore a cost-effective entry into our UTP tester series.The fast system is used to implement scalable functional test applications for a test item (single device under test) with multiple RF channels and mixed-signal test options. Depending on the adapter, the DUT can be tested at circuit board level (FKT) or when installed at the end of the line (EOL).Depending on the test item requirements, we configure the appropriate number of channels and integrate the necessary interfaces directly in the adapter or tester. The test speed, production volume and overall complexity of the UTP 6010 interfaces can be varied according to your requirements.
-
product
Fiber Cleaver
Shenzhen Sharingtek Communication Co., LTD
Is used to cut your fiber so you have two ends that will line up and can be welded together using a fusion splicer or they can be brought together in a mechanical splice.
-
product
Acoustic Test Chambers
Small Device Test Chambers are used for >Basic sound level measurement of small products and equipment >Pre-compliance testing of small products and equipment >End of line manufacturing test on small products and equipment Small Device Test Chambers provide acoustic isolation from outside sounds and/or reduce the sounds from the device under test radiating into the host
-
product
End-to-End Flight Line Confidence Test Set
MEON™
MEON™ is an end-to-end flight line confidence test set for directional infrared (IR) countermeasures (DIRCM) and ultraviolet (UV) missile warning systems. It also incorporates an IR beacon and an IR detector to provide complete, end-to-end testing, alignment checks and calibrated radiometric measurement of DIRCM.
