Test Benches
worktable including instrumentation, fixturing and unit under test.
See Also: Bench, Benchtop Chambers, Bench Multimeters, Test Bench
-
product
High Voltage Safe Measurement Systems
For measurement on high-voltage components with certified safety – in test drives, field tests, and on test benches: CSM’s high-voltage measurement systems are specifically designed for the safe and accurate acquisition of temperatures and analog sensor signals in HV environments, especially in electric and hybrid vehicles.
-
product
Detector Test Bench
RTB 3000
The RTB 3000 Detector Test Bench from Santa Barbara Infrared (SBIR) is a flexible integrated IR detector test station for evaluation of single element detectors, linear arrays, and focal plane arrays. The RTB 3000 provides the radiometric stimulus necessary to perform accurate IR detector testing in both laboratory and production environments.
-
product
Battery Testers
EEST 50-60
Charge/discharge and test benches for aerospace batteriesCharge/discharge benches for the maintenance, the certification, the training and the homologation of all industrial battery types
-
product
Capture & Replay System
PacketStorm Communications, Inc.
The PacketStorm CRS is a packet capture and replay system with hardware time stamping at 10Gbps. The user specifies which packets to capture based on the filter parameters. Packet captures can be continuous or stop capture after a certain number of frames, bytes, or time. The 10G filters include: Source Address, Destination Address, Source Port, Destination Port, and Protocol. The CRS file management includes automatic file compression and decompression. Operation is via the console or the remote GUI. There are two CRS versions: 1U and Lunchbox. The 1U version is intended to be installed in a rack or on a test bench. The lunchbox version includes a keyboard, mouse, and monitor and is intended to be moved about between stations and labs.
-
product
Hand Adapters / Special Adaptations
*Hand adapters*Combi adapters*Service adapters*Rigging harnesses*Hand over adapters for engine test benches*Cockpit test systems*Special test benches ...*For every adaptation job the fitting adapter - application specific, reliable, robust with threaded and spring loaded contact pins.
-
product
AC Power Supply and Frequency Converter
P Series
The P Series AC Power Supply and Frequency Converter for your test bench or test rack delivers clean regulated AC power in a (2U) 3.5" high and (3U) 5.25” high bench top unit that easily converts to rack mount, for far less cost than competitive models.
-
product
RAMP TEST SET
AN/USM
Tel-Instrument Electronics Corp.
The AN/USM-708 Multi-Function Test Set provides unsurpassed reliability and ruggedness designed by an established and well recognized company with 50 years in the design and manufacture of aviation ground support and bench test equipment.
-
product
Solar Simulation Systems
Solar simulation systems with global radiation guarantee the simulation of natural sunlight according to CIE20 and CIE85 Table 4. Our portfolio includes components, systems and systems for solar simulation for test benches in the automotive, military, aerospace, railway, photovoltaic, material research and building materials industries. Our plants and systems stand for high reproducibility and precise test results.
-
product
Single Phase Energy Meter Test Bench Type KP-S1000-A
Bofa Instrument & Equipment Co., Ltd
Single phase test bench, type KP-S1000-A, is a new generation, high precision energy meter calibration equipment. It can test mechanical energy meter and electronic energy meter, in spite of open or closed test link (I-P link). It is an ideal testing equipment for energy meter factory or R&D institute. All the testing procedures can be automatically operated by PC or by Keyboard manually.
-
product
Test bench for Diagnostics of Brake Valipers
MS300
Diagnostic equipment MS300 for repair and diagnostics of brake calipers. MS300 is manufactured fromanti-corrosion materials resistant to chemical effects of the brake fluid. The tabletop and the control panel are made of stainless steel, itensuresa long-lasting service of the equipment. A pressure indicator andhigh-pressure pumpcontrol elements are located on the control panel. There is also aconnection coupling fortested units. There is a gutter along the tabletops perimeter preventing the brake fluid from draining on the floor. For convenient use of tools, there is a section with perforation on the back side.
-
product
Fuel Display Unit Tester
MS 1125
Fuel Display Unit Test Bench is a compact table-top test bench with front panel controls, indications, built-in signal simulator and necessary power supply for testing the serviceability of Fuel Display Unit of Helicopter. FTB operates on 230 V AC and supplies 28 V DC power to FDU. FTB is housed in a metallic cabinet FTB interfaces with both 61 Pin connector and 6-pin socket mounted on the rear panel of FDU by means of the cable connected to the unit. FTB is fabricated utilizing off-the-shelf standard industrial/commercial components like rotary switches, toggle switches, press switches, test sockets, fuse holders, potentiometer etc. The Frequency generation circuit is integrated into FTB for the simulation of Fuel probe and flow rate signals. The frequency of the signal can be selected by means of a rotary switch Low amplitude sine wave signal is simulated for testing flow rates. Variable voltage DC power supply with a voltage range of 24 to 29 Volts is provided within FTB to power-up FDU. 5 V DC is provided for the operation of signal generating circuit (PIC Frequency Controller Board). An off-the-shelf Hand held battery operated Digital Multimeter (DMM) procured from the prominent manufacturer (FLUKE) is supplied with FTB for setting up and measurement of various parameters like Resistance, Voltage, Frequency etc.
-
product
Single Phase Round Energy Meter Test Bench Type KP-S1000-C
Bofa Instrument & Equipment Co., Ltd
Single phase round energy meter test bench, type KP-S1000-C, is a special calibration equipment for testing Round (ANSI Socket type) energy meter and normal energy meter with bottom terminal block. It is an ideal testing equipment for energy meter factory or R&D institute, especially for testing ANSI Socket type energy meters. All the testing procedures can be automatically operated by PC or by Keyboard manually.
-
product
LSI Functional Verification Services
SpecInsight
The keys to functional verification are “verification strategy” and “highly complete verification item extraction.” Our functional verification services emphasize highly complete verification item extraction while also generating test benches and functional scenarios, random verification, and even functional coverage to meet customer demands by providing these services from a wide variety of angles. By implementing functional verification on the RTL and C models designed by customers from a third-party perspective, we improve quality of customers’ circuits.
-
product
Safety Valve Test Bench
Nagman Instruments & Electronics Pvt. Ltd
Safety Valve Test Bench is a very easy, safe, accurate and maintenance free operating work shop test unit for Testing & Calibration of pressure/safety relief valve.
-
product
GoldenGate RFIC Simulation Software
GoldenGate RFIC Simulation and Analysis Software is an advanced simulation and analysis solution for integrated mixed signal RFIC designs that is fully integrated into the Cadence Analog Design Environment (ADE). GoldenGate is part of Keysight's RFIC simulation, analysis and verification solution that also includes Momentum for 3-D planar electromagnetic simulation, SystemVue & Ptolemy wireless test benches for system-level verification, and the Advanced Design System (ADS) Data Display for advanced data analysis. This suite links the RF system, subsystem, and component-level design and analysis as part of a unique and comprehensive RFIC design flow.
-
product
Electric Burn-in Board Carts
Conforms to SEMI ergonomic standards Holds and transports card cages for semi-automatic loading/unloading. Holds up to 10 burn-in boards. Raises and lowers the burn-in boards for easy loading/unloading of boards into ovens or onto test benches. Cart can be adapted to dock with any Micro Control oven.
-
product
KWH Meter Test Bench
This test bench is widely used in electrical and engineering sector for varied testing applications.
-
product
Gyro Evaluation & Test Equipment
MS 1113
The automatic test bench for gyros (ATP) is used to carry out the final acceptance test for the gyros in the stand-alone mode. It is a PC based test set up incorporating standard and custom built test and measuring instruments interfaced by GPIB bus. The gyros are installed on the platform, which is used to provide information pertaining to the angle at which aircraft is flying.
-
product
Battery Simulator
G5.BAS
The G5.BAS series is bidirectional regenerative. It was developed specifically for the simulation of energy storage devices and batteries and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3.
-
product
Battery Tester
G5.BT
The G5.BT series is bidirectional regenerative. It was developed specifically for testing energy storage devices and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The G5.BT series has an outstanding current accuracy of <0.02% FS, an additional high-resolution current measurement range, and a fast current rise time in the 100 μs range. Ripple modulation, an integrated safety relay for PL c according to EN ISO 13849 and a powerful CAN multi-protocol interface (1 kHz, 16 bit) as well as functions to avoid reverse-polarity problems, current surges, and unwanted deep discharges make the G5.BT series the ideal, versatile battery module and battery pack tester.
-
product
Phase Angle Meter
597C
Red Phase Instruments Australia Pty Ltd.
The Model 470A has similar software and performance as the Model 465C. It is packaged in a 19? style bench-top case with all connections on the front panel for use in meter test benches. It has inputs for comparison with another polyphase standard or 3 separate single phase standards for verifying calibration accuracy.
-
product
Powerful, Fully Integrated Workstation for Emission Microscopy
PEM-1000
The PEM-1000 emission microscope incorporates the latest technology in real time, high quantum efficiency, mega-pixel CCD detectors in a back-thinned cooled camera. A portable system, the PEM 1000 can interface with all analytical probe stations, ATE (automated test equipment) and bench top configurations for high speed functional testing.
-
product
MCB Magnetic (Instantaneous) Trip Test Bench
The test bench is specially built for low voltage- B, C & D curve MCBs. Specially designed custom built jigs are able to accommodate single, double, three and four pole MCBs. Decades of experience has helped us to design current source (transformer) in a special way such that good current regulation and high accuracy is ensured with a variable range without the use of any variable transformer in the system. The product is better than the competition with conventional technology at a lesser price!
-
product
DMX Tester
DMXter 2U
Here's the DMXter 2U, a Lil'DMXter2 for bolted down applications. All the hardware and software features of the standard Lil'DMXter2 in a 2U 19" rack box, plus many new features.The user controls, the XLR connectors, and the LED illuminated LCD display are on the front panel. The 2U is equally at home as the back up controller in a theatre or TV studio, running a trade show booth, the background lighting for themed entertainment or as the built in test controller in a touring show DMX distribution rack. Its increased I/O capabilities will make it a useful addition to your test bench.
-
product
Test bench for Infrared Focal Plane Array detectors
BIRD
The BIRD bench enables characterization of any types of Infrared Focal Plane Array (IRFPA) detectors.
-
product
Space Flight Components
A tec, Inc. specializes in the design, manufacture, and integration of complex test systems and quality critical components. Our production engineering expertise separates us from other manufacturing companies when both reliability and cost are important. Atec has the best in 5 to 9 Axis CNC machining, coordinate measuring machines (CMMs), 3D additive metal and plastic printers, 9-Axis capable waterjet, cryogenic liquid flow test benches and environmental test chambers. We can deliver to the tightest tolerances and most exacting requirements. We can advise our customers on electron beam welding, friction joining, electronic test, environmental test, acoustics, vibration and many other technologies that can reduce manufacturing and operating costs. We are currently manufacturing liquid rocket engine fuel and oxidizer valves for multiple launch vehicles and have participated in 158 consecutive launch successes. Atec manufactured and tested advanced lithium-ion battery adapter plates that manage power for the International Space Station. Atec is designing, manufacturing, and testing power flow modules that work to prevent system failure on the human crew capsule (CCTS) that will transport astronauts to/from the ISS. Atec was awarded NASA Agency-Level Small Business Subcontractor of the Year , SBA Region VI Subcontractor of the Year for our support to NASA and Boeing and we were named a DCMA Top 500 Supplier.
-
product
Environmental Simulation Chambers
GTEMCELL , currently provide environmental test chambers made by LIB.Our standard range of test chambers includes bench top and floor standing models, across temperatures ranging between -65℃ and +150℃ (from -80℃ to +200℃ for specific applications), and humidities between 10% and 98% RH.
-
product
Portable Test Bench For Single Phase Energy Meter
SY 2100
Hong Kong Songyang Industrial Ltd.
Anthropomorphize design, Large size LCD display, easy operation. High stability, good reliability. Reasonable internal structure. Compliance with IEC736.ISO9001 certificate. Automatic switchover of voltage or current output to protect equipment when voltage circuit short or current circuit open and alarm display on LCD
-
product
MCB Tripping Current Characteristic Test Bench
The SCR Elektroniks 12 station MCB Tripping Characteristics Test Bench is optimally designed to verify the Tripping Characteristic of MCBs as per clause 9.10.1 of IEC 60898 (Also mentioned in Indian Standards IS 8828). The bench essentially comprises of Servo Controlled mechanism to set and maintain desired current (against incoming mains fluctuation) and a Micro controller based master controller unit plus timer, which governs the entire sequence of operation making it a stand-alone system once the user connects the MCB and configures the test parameters.
-
product
Test Bench Software
HORIBA TestWork
The versatile, customizable HORIBA TestWork operating software serves as a central tool for test bench management and control. Thanks to its high level of flexibility, it can be precisely tailored to a wide range of applications. At the same time, the intuitive interface enables fully automated execution of even complex test runs without losing sight of the essentials.
