Isolation
-
Product
Isolation Transformers
-
Osborne’s Isolation Transformers are used to step-up, step-down and isolate voltages in single phase circuits. Isolation may be used to provide output circuit immunity from voltage spikes and noise (both common-mode and transverse-mode) present on the input system. The isolation can allow separate grounds on both the input and output sides of the transformer. Osborne also designs with a range of electrostatic shielding to provide several levels of noise immunity.
-
Product
TAP Signal Isolation Module
JT 2139
-
The JT 2139 is a TAP signal isolation module designed for use in combinational test systems that utilise multiple instrument interfaces. To avoid parasitic capacitance effects and/or unwanted ground loops the JT 2139 can be used to completely galvanically isolate any JTAG Technologies boundary-scan controller from the remainder of the instrumentation system. JT 2139 isolators are a standard component of the JTAG Technologies ‘Symphony’ systems that integrate boundary-scan with In-Circuits Testers etc..
-
Product
High Density, High Isolation Multiplexer Module
1260-38T
Multiplexer Module
The Astronics 1260-38T brings a combination of density, versatility, expandability, and high signal integrity, making it ideal for construction of large switching systems. This module is user-configurable using inter-connecting relays as sixteen 1x8 muxes to a 1x128 mux under program control. Special shielding, design, and added front panel "guard" grounds increase the isolation and lower the crosstalk.
-
Product
8 Channel Relay Board for Signal Isolation
FXA-104 Relay 8CH
Relay
The FXA-104 is a relay board to switch signals with 8 SPDT channels. It’s eight channels can be switched individually with a low active input. Each channel is equipped with a status led and capable of switching up to 2A. Due to its wide range input it’s very flexible to use and it is delivered with an installed DIN rail carrier.
-
Product
Isolation Amplifier Digital Output
-
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a digital signal (MDAT, MCLK) output function on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
Product
True Online UPS Systems with Inbuilt Isolation Transformer
-
Our software and connectivity devices incorporate all the features you need to proactively manage your systems, from basic monitoring and shutdown to predictive analysis and power management. Aplab Integration Services offer complete solutions tailored for the specific requirements of Defense Services, Telecom and Commercial markets.
-
Product
JTAG Isolation Protection
-
Our line of JTAG isolators help protect your investment in computers, development boards, debug probes, and lab equipment. Each model connects easily between your target board and debug probe.
-
Product
BenchMate with Horizontal Isolation
2214 Series
-
BenchMate Vibration-Free Platforms enhance the performance of precision tabletop equipment.The 2214 Series is very similar to the 2212, however it has the added benefit of multistage horizontal isolation. It is recommended in applications where horizontal vibrations are a problem.
-
Product
Bus Isolation Board
MS 1705
-
- Bus Interface - ISA96 Bus, 6U form factor- 16-bit Data Bus- 20-bit Address Bus & Control Signals- Isolated Bus Interface- Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Isolation Amplifier
-
Mornsun Guangzhou Science & Technology
An isolation amplifier is an amplifier that provides isolation between the input and output of the circuits, including isolation between their associated power supplies. MORNSUN offers different types of analog isolation amplifiers, such as acquisition type signal conditioning modules, output isolation signal conditioning modules, two-wire loop power supply signal conditioning modules and signal isolators, etc. These analog isolation amplifiers feature excellent temperature drift characteristics of less than 50PPM/℃ across the entire operating temperature range of -40 ℃ to +85 ℃ and achieve isolation transmission, signal conversion (programmable for some models), HART communication, signal amplification, port protection and other functions. SIP, DIP, SMD and DIN Rail packages are optional.
-
Product
Isolation Adapter
-
For harsh environments and motor control applications where debug tools may be exposed to high voltage or ground loop potentials, Blackhawk offers two product models of galvanic isolation.
-
Product
Isolation Amplifier
-
An electronic device used to electrically separate input, output, and power supply circuits while conditioning or amplifying measurement signals.
-
Product
Cell Isolation & Analysis
-
Life's complexity originates in cells, spanning cellular structure, genetic diversity, gene expression, and complex tissue formation. Serving as the fundamental unit, cells form the foundation of all biology. Characterization of cells, their processes and interactions can provide insights into areas like medicine, symbiosis, and biological diversity. Bio-Rad supports these inquiries, offering innovative technologies for your cell biology research.
-
Product
Isolation Amplifiers
-
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
Product
PXI 5A Power Multiplexer, 1-Bank, 48-Channel, Isolated Common, Independent Isolation
40-651A-111
Multiplexer Module
The 40-651A-111 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats.
-
Product
High Isolation USB Switches
-
RF gain block amplifier from Pasternack is featured in our extensive in-stock RF amplifier selection. Our connectorized gain block RF amplifier uses SMA connectors. This SMA gain block amplifier has a minimum frequency of 500 MHz, a maximum frequency of 2 GHz and a typical gain of 17 dB.
-
Product
Isolation Amplifiers
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Unipolar and bipolar DC input signals 20 mV to 200 V and 0.1 mA to 100 mA calibrated range selection. Working voltage up to 1000 V AC / DC.
-
Product
PXI 5A MUX, 1-Bank, 48-Chan, Ind. Isolation
40-651-101
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
-
Product
Advanced Reconfigurable Modular OTA RF Test Enclosures, ≥100 DB Isolation, 300 MHz - 90 GHz
dbSAFE ARMOR
-
The dbSAFE ARMOR series of shielded boxes are cost-effective solutions for OTA testing in the mmWave spectrum. Providing a shielded, fully anechoic test environment, these RF test enclosures ensure stable and repeatable measurements over a wide frequency range (from 300 MHz to 90 GHz).
-
Product
High Isolation 1310/1550nm WDM
HWD1315
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HWD1315 high isolation WDM is based on mature thin film filtering tech, metal sealing technology package. HWD1315 is used in combination and separation of 1310nm and 1550nm band optical signal. Its wide bandwidth, flatness, low insertion loss and isolation are higher than the average MWDM devices and so on.
-
Product
RS422 Mode SI-module With Optical Isolation
MX422-G
-
RS422 mode SI-module with optical isolation
-
Product
Ultra-Low Frequency Spring Activated Vibration Isolation Workstation
MK26 Series
-
The New MK26 Series Vibration Control Workstation with more ergonomic comfort is designed specifically for ultra-low natural frequency applications. Kinetic Systems manufactures the system utilizing the Minus K patented negative stiffness vibration isolators in order to provide a compact, passive Vibration Isolation Workstation with ultra-low natural frequencies, higher internal structural frequencies, and excellent vertical and horizontal isolation efficiencies. The MK26 has also been upgraded to provide much better user comfort and additional leg space.
-
Product
PXI RS232 Interface Galvanic Isolation
PXI‑8432/4 - OTP2-Modul-Nr196
-
The PXI‑8432/4 module is a high-performance, dielectric-proof interface for high-speed communication with RS-232 devices. The module offers data transfers via the high-speed DMA interface, multithreading and multiprocessor support. NI serial ports appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Interface and Isolation
-
Analog Devices offers a wide range of digital interface and digital isolators with iCoupler® technology covering the industry’s field bus and peripheral communications standards. Digital isolators, isolated transceivers, isolated A/D converters and isolated gate drivers utilize the award winning iCoupler® and isoPower® technologies for isolation solutions without many of the constraints found in optocouplers. Find design solutions for interface devices including keypad controllers, level translators, and high voltage protection products (channel protection, fault protection, overvoltage protection), and latch-up proof switches and multiplexers.
-
Product
2-Port CAN-Bus MIOe Module With Isolation Protection
MIOe-3680
-
Operates two separate CAN networks at the same timeHigh speed transmission up to 1 Mbps16 MHz CAN controller frequencyOptical isolation protection of 2,500 VDC ensures system reliabilityI/O address automatically assigned by PCI PnPLED indicates Transmit/Receive status on each portWindows DLL library and examples includedSupports Windows CE5/CE6/XP/7 driver and utilitySupports Linux 2.4.xx / 2.6.xx; QNX 6.3x/6.4.x/6.5.x Intel x86 hardware platform2-Port CAN-Bus MIOe Module with Isolation ProtectionGet Quote
-
Product
Nucleic Acid Isolation - Research
-
Based on PerkinElmer patented magnetic bead technology the chemagic instruments represent ideal solutions for nucleic acid isolation in a huge variety of research market segments including but not limited to Human Genetics, Biobanking, HLA Typing, Virus and Bacteria Detection.
-
Product
Large Size RF Test Enclosure, ≥100 DB Isolation, 300 MHz - 18 GHz
dbSAFE MAX
-
Some applications require larger test environments. The dbSAFE MAX blends all the superior isolation characteristics of the standard dbSAFE DUO shielded box into a larger volume to guarantee you get better results.
-
Product
Safe Isolation & Lockout Tagout
-
Our range of Safe Isolation Kits and and our NEW lockout devices for isolating circuit breakers, RCD's and MCCB's, enable you to work safely on installations, following the safe isolation procedure, without the risk of electric shock. All our devices and equipment are easy to use and all equipment is supplied with Lockout Tags to identify the device is locked and who to contact in the event of an emergency.
-
Product
Analog Signal Conditioning &Isolation Products
DSCIA
-
DSCIA module is a signal channel isolated analog input or output.
