Tables
See Also: Vibration Isolation
-
Product
60 GHz Noise Figure Test Set
-
The Noisecom 60 GHz Noise Figure test set has 4 separate systems designed to perform Y-factor noise figure measurements using a high performance Spectrum Analyzer or a dedicated receiver. Each system contains a highly stable V-band noise source, isolator(s), optional waveguide to coaxial transitions and an optional pre-amplifier for use with a spectrum analyzer. The two standard calibration tables have ENR data points at 1 GHz intervals.* System ENR is measured before the DUT connector and at the final output stage allowing for pre-test calibration of the system.
-
Product
10 Micron Wire Grid Polarizer
-
Fabricated from 10 micron diameter tungsten wire, and with a choice of wire spacing starting from 25 microns, these wire grid polarizers are suitable for use from approximately 100 microns (or 3 THz) to longer wavelengths. Please refer to the table below for the standard availability of wire spacing and frame clear aperture / outer diameter.
-
Product
PCMCIA Card
DAS-429PCMCIA/RT10
-
Both cards contain 68 Kbytes of true dual-port RAM, for data blocks, control registers and Look-up table, mapped within the Common Memory space. The card also contains a FLASH-based Card Information Structure (CIS) within the Attribute Memory space.The cards comply with the Personal Computer Memory Card International Association (PCMCIA Release 2.1) standard, including Plug and Play. The card's small size and suitability for PCMCIA compatible notebook computers with Type II and Type III slots make it a complete solution for developing and testing ARINC-429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The cards are supplied with C drivers, including source code, Mystic Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
DC Blocking L-Band Splitter Combiner
PD5940
-
INSTOCK Wireless Components, Inc
PD5940 is an IP67 outdoor, weather resistant, DC blocking, four way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5940 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 4 way power divider input rating tables for additional power handling info.
-
Product
Present Weather Sensors
-
Bristol Industrial & Research Associates Ltd
Biral forward scatter Present Weather Sensors measure visibility and report precipitation type and intensity. These compact sensors can identify a wide range of precipitation types including drizzle, rain, snow, hail, freezing rain and other forms of frozen precipitation. Precipitation type is reported using a combination of WMO Table 4680 and METAR codes. The range of precipitation types identified varies with sensor model.
-
Product
Rear Cover, G12, Tabletop Configuration
310113421
Protective Cover
The G12 Rear cover is designed to connect to the Receiver in a Table top configuration and act as a mean to hide the cables that are running back to the testing equipment. This works well with applications where the cables are running down to a lower level below the G12.
-
Product
Clover Honey 5 pounds
-
5 LB of pure raw clover honey.Clover honey is what most people think of as being typical honey flavor and color. It is widely used "on the table." Clover is the most common nectar producing plant. Dutch White, Alsike, White Sweet and Yellow Sweet clover plants are the most important for honey production. Depending on location and source, Clover honey varies in color from water white to amber and has a mild, delicate flavor.
-
Product
Motion Simulation
-
Exail's motion simulators are at the forefront of calibrating and testing inertial sensors, navigation systems, and optronic payloads across diverse applications, from traditional land vehicles and aircraft to emerging sectors like autonomous vehicles and wearables. With 60 years of expertise, Exail's rate tables deliver unparalleled performance, accuracy, and reliability, offering a cost-effective solution tailored to meet customer needs at every stage of product development. From concept to maintenance, Exail provides comprehensive support, ensuring the success of each project
-
Product
Preamplifiers
-
A.H. Systems'' Preamplifier line is an excellent choice with a rugged design, no hassles with soldering your own power leads and they improve overall system sensitivity by at least 20 dB. All of A.H. Systems'' Preamplifiers come with a 12-volt (or 15-volt) DC regulated power source. A low voltage indicator confidently allows you to power the amplifier with your own external 12-volt DC battery. This makes it a convenient choice for field measurements. See table below for amplifier specifications.
-
Product
Table Tops Equipment
-
RECIF Technologies 150-200mm product range is composed of various kind of table tops equipment including wafer transfer, aligners and elevators.As a result of a technology license agreement, with its European partner EMU Technologies, RECIF proposes updated designs for its equipment line, without compromising the proven performances installed on the field for years.
-
Product
Compact Goniophotometer For Lamp Spread Angle Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
LCG-1600 Goniophotometrc System carries out measuring methods of fixed location and rotating luminaires. The measured luminaire is installed on the two-dimension rotating table, using “+” laser to make the luminaire lighting center superposed with the rotating center of rotating table. The mechanical equipment allows turning the tested luminaires around a vertical axis and a horizontal axis. When tested luminaires turn around horizontal axis, the detector which is at the same level with rotating table will measure the intensity of each direction at this surface. When rotating with vertical axis, the detector will measure the intensity at the vertical surface. The vertical and horizontal axis can be rotated continuously at ±180° or 0~360°. According to the measurement requirements, the system can be operated in C-γ coordinates. When getting intensity distribution data, computer will calculate other photometric parameters automatically.
-
Product
ATSC 3.0 Broadcast Stream Verification
StreamScope XM Verifier
-
The Windows®-based Verifier web app receives, tests, and records ATSC 3.0 broadcast streams from RF, Ethernet, and file inputs. With Verifier, you can monitor real-time graphs and charts of bitrates, signaling tables, RF parameters, packet errors, subframes, PLPs, and other KPIs.
-
Product
Temperature Logger For Human Body Range
HBTS 2.0
-
The HBTS is designed to monitor the temperature of parts, gas or liquids associated with intended/unintended heat to the patient. High accuracy and resolution is achieved in a range of 0-75°C. Typical standards are IEC 60601-1 (Table 24), IEC 60601-2-18 (endoscopes), IEC 60601-2-19 (infant incubators), IEC 60601-2-21 (radiant warmers), ISO 80601-2-74 (humidifiers).
-
Product
Differential Pressure Transmitter Trainer
-
Unitech Scales And Measurements Pvt. Ltd
This table top model comprises of two pressure chambers. One for high pressure and another for low pressure. The two pressure chambers are fitted with pressure gauges. The differential pressure transmitter is connected to the two chambers. The pressure is built by a foot air pump. Digital instrument is provided to indicate the differential pressure with transmitter output.
-
Product
IP67 DC Blocking Splitter Combiner
PD5033
-
INSTOCK Wireless Components, Inc
PD5033 is an IP67 outdoor, weather resistant, DC blocking, three way, RF broadband, 50 ohm, power divider, power combiner furnished with N type coaxial connectors. The passive Wilkinson design passes RF and the 10 MHz reference signal through both ports while blocking DC current. This configuration is typically used in combining applications to prevent passing DC to the sum and adjacent ports. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5033 is a bidirectional device capable of 40 W max microwave input power levels in both power splitter and combiner apps. See 3 way power divider input rating tables for additional power handling info.
-
Product
Flow Computers
-
Cox FC30 flow computers service both liquid and gas applications. The FC30 features batching, 40-point flow meter linearization tables, and temperature viscosity correction using Strouhal/Roshko advanced linearization methods and multiple flow and control inputs. Relay outputs are independently assignable for alarms and general purpose warnings. The FC30 has serial communications, both RS232 and 485, and isolated analog and pulse outputs.
-
Product
Automotive
-
Radiometrics Midwest Corporation
A2LA accredited state of the art 10 meter, environmentally controlled, vehicle level, absorber-lined chamber is available to solve your EMC problems. Testing is performed on a 20-foot diameter turn table with a 25,000 pound capacity.
-
Product
DC Blocking L-Band Splitter Combiner
PD5960
-
INSTOCK Wireless Components, Inc
PD5960 is an IP67 outdoor, weather resistant, DC blocking, six way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5960 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 6 way power divider input rating tables for additional power handling info.
-
Product
Shore Durometer Test Stand
UI-FT31
-
Shore Durometer Test Stand is used to support the durometer presser foot surface parallel to the sample support table to better complete the test.
-
Product
IP67 DC Blocking L-Band Splitter
PD5031
-
INSTOCK Wireless Components, Inc
PD5031 is an IP67 outdoor, weather resistant, DC blocking, three way, RF broadband, 50 ohm, power divider, power combiner furnished with N type coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5031 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 3 way power divider input rating tables for additional power handling info.
-
Product
Digital Program Insertion Auditor
Torque DPI
-
The DPI Auditor supports the ANSI/SCTE 35 2001 standard that defines a fully digital mechanism to control remote splicing equipment via cueing messages embedded in the transport stream. The core of the standard is centered on an SIT (Splice Information Table) which can contain a schedule message or an insert message.
-
Product
Low Noise Coaxial Cables For Sensors
-
Low noise coaxial cables are used with single axis and triaxial charge mode sensors. This table provides relevant specifications for four cable types. Type 003 is the most commonly used, but three other types are also available.
-
Product
Inspection System for high-power precise 3D X-ray CT
X-eye PCT225
-
Inspection System for 3D X-ray CT able to analyze defected area precisely by precise movement of axis with high polished Anti-vibration table. High-power X-ray Tube of max. 450kV and large area Flat Panel Detector of max.16 inches can be installed depending on the sample. Customized 3D CT equipment is available with selecting main parts by customers depends on their needs for size and material.
-
Product
Full Function EtherCAT PCIE MDevice Card
PCIE-1203
-
667MHz dual-core ARM processor2 x EtherCAT ports for high-performance of motion and I/O applicationsSupports common motion SDK for rapid application developmentSupports PTP, linear and circle interpolation, Path table, Compare, Latch, Compare delay DO trigger functionSupports programmable acceleration/deceleration rateDiagnostics for fast error handling can trace command and error message
-
Product
IEC60335 Inclined Plane Test Table for Stability Test
CX-W600
-
Shenzhen Chuangxin Instruments Co., Ltd.
It's to determine the stability of electric appliances which are used on a table or on the floorin accordance with IEC 60065 / 1998-07 clause 19.1, IEC 60335-1 / 1991-04 clause 20.1, IEC 60601-1 /1988 clause 24.1, IEC 60950 / 1991 + Amendments, modified, clause 4.1.1,EN 60335-1 / 1994 and A11 / 1995 clause 20.1, EN 60950 / 1992 + Amendments up to 1997 clause 4.1.1,VDE 0700 Part 1 / 10.95 clause 20.1 and Part 3 / 3.96 clause 20.1, VDE 0730 Part 1 / 3.72 clause 20a,VDE 0805 / 11.97 clause 4.1.1Inclined Plane Device is used to test the stability of an apparatus that requires a surface in order to work.The device cosist of a surface and an angle adjusting device with 0- 15 °
-
Product
High Precision Angular Positioning Calibration and Geometry Inspection
LabStandard
-
Rotary Precision Instruments UK Ltd
Ultra precise rotary tables intended for fine inspection, metrology and test applications.Designed for horizontal and vertical applications with self-locking worm gearing and a high accuracy angular encoder ensures sensitivity and fine positioning for metrology and precision testing.
-
Product
CO2 Sensors
-
Beautifully designed CO2 meter / indicatorEquipped with 3 color traffic light indicatorEquipped with integrated temperature and humidity sensorVery favorable pricing, including AC adapter and table stand
-
Product
BJT Modeling
-
IC-CAP supports a number of bipolar junction transistor (BJT) models. For more information on the various types of IC-CAP supported BJT models, refer to the table below.
-
Product
Coherent Synthesizers
-
Innovative Technical Systems has developed high-performance agile microwave synthesizers with truly phase-coherent frequency switching at any step size. These synthesizers offer frequency coverage from 250 MHz to 18 GHz (ACS-25018) or 850 MHz to 18 GHz (ACS-85018) and frequency resolution under 0.1 Hz. The agile design offers typical switching speeds of less than 300 nsec and programmable amplitude from 0 to +10 dBm from frequency-to-frequency. Spurious performance is typically <-70 dBc. A versatile waveform table design is implemented that allows frequency, amplitude, and output markers to be defined for each step in the table. Waveform table lengths up to 256K are supported.
-
Product
DUMMY BLOCK
STAG 10
-
Ideal requirements of release agent between billet and dummy block:Optimal adhesion to the substrate, Optimal anti-soldering power, No hazardous fumes/vapors development during use, Non-flammable at the effective temperature, No build-up, no interferences on run out table.
