Op Amps
IC used as voltage amplifier. Also known as: Operational Amplifiers
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
Operational Amplifier
Op Amp Series
-
The amplifier is capable of operating at supply voltages from 0.9V to 3V with specified specs at 1V and 1.8V single supply.The input common mode range extends to both power supply rails without the offset glitch and input bias current phase reversal inherent to most rail to rail input amplifiers.
-
Product
High Speed Op Amplifiers (Bandwidth ≥ 50MHz)
-
Analog Devices high speed (> 50 MHz) amplifiers are the number one selling brand of high speed amplifiers in the world today. Whether it's wide bandwidth, high slew rate, or low distortion, no one sets more performance standards for next generation designs, with the widest portfolio of leading edge products, than Analog Devices. Designers who want dependable, reliable parts that enable the highest performance from their design come here for the ultimate source in high speed op amps.
-
Product
Analog LCD Display Drivers
-
Analog Devices analog LCD display drivers provide a diverse range of options for industrial and commercial applications. The larger than standard rail-to-rail output swing offered by select members of this product line help enable applications requiring greater dynamic range than standard video op amps allow. The high slew rates and high capacitive drive capacity found in this portfolio make it ideal for LCD applications, while low supply current options support battery-powered technology.
-
Product
Low Input Bias Current Amplifiers (<100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
Active Differential Probe
DF-600
-
The DF-600 Differential Active Probe is a high input impedance and low input capacitance probe. It also supports extremely high frequency bandwidth, and high voltage input. It is designed using three OP amps, namely two FET buffer OP amps and a low offset OP amp. Therefore, even with long-term operations, the measured voltage will not drift. The voltage offset always approach 0 volts. (USB power supply should be 5V ±2%). The following diagram shows the circuit of DF-600.
-
Product
OPS Digital Signage Player
-
Intel Open Pluggable Specification (OPS) compliant digital signage platforms enable digital signage manufacturers to simplify the installation, maintenance and to deploy systems faster with lower costs.
-
Product
Field Ops Remote Tracker
-
10 meter positional accuracy for every kilometer traveled – without the use of GPS or RF beacons.
-
Product
Precision Op Amplifiers (Vos <1mV & TCVos<2uV/C)
-
Analog Devices' broad range of precision amplifiers provides industry-leading support to designers in need of traditional trimmed and zero-drift amplifier technology. Our precision amplifier family helps preserve the accuracy of dc information in an incoming signal with low offset voltage (VOS < 1 mV) and low temperature drift characteristics (TCVOS < 2 V/C).
-
Product
48V / 200 Amp Load
EL12-48M
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with Telecom 48V Rectifiers and Power Supplies with output Voltages in the range of 38V to 60V and is extremely costeffective.
-
Product
110V / 90 Amp Load
EL12-110M
-
For Telecom Rectifier and Power Supply testing. This particular Load has been designed to operate with Telecom 110V Rectifiers and Power Supplies with output Voltages in the range of 100V to 135V and is extremely cost effective.
-
Product
High Side Current Sense Amp
QA150
-
The QA150 makes ultra-low current measurements of your toughest real-time projects a snap. The QA150 is a high side current to voltage converter. Simply tap into the supply for your various project rails (5V, 3.3V, etc) and the QA150 will convert the currents to voltages that you can then capture on your scope, along with whatever other signals you might need. If you are trying to squeeze every last bit of energy from your batteries, the QA150 is your answer.
-
Product
48V / 200 Amp Load
BD12-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
Dual Channel Servo Amp
Servo Amp
-
This is our Dual Channel Servo Amp board that the instrument shop can use for testing HSI's like the 331A-( ) series and others or RMI's. This board is standard in our model TA-1000 HSI tester.
-
Product
24V / 400 Amp Load
BD12-24P-12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 24V battery systems and is extremely cost effective.
-
Product
Receiver, G3, 500+ Amps, includes Dedicated 500+ Amp Module
310105172
-
Receiver, G3, 500+ Amps, includes Dedicated 500+ Amp Module.Contacts rated to 1500VDC for low duty test applications.Mating ITA 410105174. (NOT compatible with other VPC Solutions)
-
Product
48V / 250 Amp Load
BD15-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
1000 Amp High Accuracy Current Probe
HA1000
-
The HA1000 is our most accurate current probe. The HA1000 clamp-on current probe measures from 1 to 1000 amps AC.
-
Product
30 Amps, 100 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP031
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Switch Amp
-
One of many potential designs, Teledyne RF & Microwave's switched amplifier covers 100 to 2000 MHz, providing 18 dB gain, phase matched to within ±1.0 degree. The primary RF input and a secondary calibration signal input are switched, then amplified, and split to two outputs. Gain balance between any of the two outputs is ± 0.5 dB. Output power at 1 dB compression is +14 dBm and input/output VSWR is 2.0:1 maximum.
-
Product
PXI 2 Amp MUX, Dual 16-Channel 2-Pole
40-635-006
-
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
Portable Current Supply 10 AMP output
CS-10
-
The CS-10, Sure beats carrying around a rectifier and generator...
-
Product
PXI Battery Simulator 2.8 Amps
41-753-001
-
The 41-753 is a battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals that can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Product
PXI 2 Amp Multiplexer, Quad 4-Channel, 2-Pole
40-635A-109
-
The 40-635A-109 is a quad 4-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI 2 Amp MUX, Dual 32-Channel 1-Pole
40-635-005
-
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
48V / 200 Amp Load
BD12-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
PXI/PXIe Power Relay Module, 5xSPST, 30 Amp
40-166-002
-
The 40/42-166-002 is a PXI/PXIe high density power relay module with 5xSPST switches rated at 30A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations. It uses power relays which are suitable for switching loads up to 20A at 240VAC (SPDT & SP4T versions) or 30A at 277VAC (SPST versions).
-
Product
PCI 2 Amp Multiplexer, Single 8-Channel, 4-Pole
50-635A-103
-
The 50-635A-103 is a single 8-channel, 4-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
110V / 100 Amp Load
BD12-110P-48/24
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 110V battery systems and is extremely costeffective.
-
Product
PXI 2 Amp MUX, Dual 4-Channel 4-Pole
40-635-107
-
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI 38 Channel 2 Amp Multiplexer Card
40-656-001
-
A 38-channel multiplexer, 2-pole switching, suitable for switching signals to 2Amp, 220VDC/125VAC. It offers the highest switching density in its class for medium power/ voltage signals. Specifically designed for switching POTS, ISDN or xDSL telephony signals. Bandwidth for most configurations is typically >25MHz. It is paired with a very similar module, 40-655-001, a multi-banked multiplexer.
