Gas Flow
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
Check It! Gas Analyzer
F-920
-
The F-920 Check It! Gas Analyzer is a device that rapidly measures CO2 and O2 from 0-100%. Designed for QA personnel to take precise and speedy measurements of CO2 and O2, the Check It! displays results in less than 6 seconds and has a sampling volume of 6.5 mL.
-
Product
SF6 Gas Purity Tester
-
Weshine Electric Manufacturing Co., Ltd
In operation and during electrical failures, pollutants are generated which, depending on its concentration, reactivity and toxicity, modify the characteristics of gas for insulation and arc extinguishing. This may affect the safety of the installation and people. Gas handling operations can also cause the incorporation of pollutants.
-
Product
Portable Single Gas Monitor
Protégé ZM
-
Teledyne Gas & Flame Detection
The Protégé ZM single gas monitor is an easy-to-use, zero maintenance gas detection solution that delivers high performance in a small, ergonomically designed package. It is available in oxygen, carbon monoxide and hydrogen sulphide single gas models. This single gas monitor is incredibly reliable, giving industrial workers and first responders the confidence to focus on the task at hand, not on their equipment.
-
Product
Gas Generators
-
HPLC is an analytical method used to separate the components in a mixture, to identify each component, and to quantify each component. It relies on pumps to pass a pressurized liquid solvent containing the sample mixture through a column filled with a solid adsorbent material. Each component in the sample interacts slightly differently with the adsorbent material, causing different flow rates for the different components and leading to the separation of the components as they flow out the column.
-
Product
OEM Gas (NO) Analyzer
BE-220FSD
-
The BE-220FDS is an OEM NDIR detector for measuring NO in automotive emission gases. The BE-220FSD can output NO concentration by digital data and analog voltage. In addition, it can be connected with the HORIBA BE-150 bench by serial line and relay the commands for BE-150. The BE-220FSD meets OIML Class 0 and complies BAR-97 & GB18285-2018 specifications.
-
Product
Dual Display Digital Pressure Sensor [For Gas]
DP-100L
-
Panasonic Industrial Devices Sales Company of America
Panasonic’s compact DP-100L Pressure Sensor with IO-Link features an improved digital display that offers increased clarity and a wider viewing angle. Thanks to a redesign of its circuitry, the low-power-consumption DP-100L Series requires 14% less power during normal operation and when operating in ECO / FULL mode the display is completely shut off for an increased power savings of up to 50% compared to normal operation. The current value and the threshold value can be checked at the same time, so the threshold value can be set and checked smoothly without switching to another screen mode.
-
Product
Combustible and Toxic Gas Detection
IMR IX616
-
IMR Environmental Equipment, Inc.
It has a high-quality sensor, and uses natural diffusion as the method for detection. It has high sensitivity and reproducibility. It also uses an embedded MCU controller and is easy to operate. The shell has special high strength anti-slip rubber it is water-proof, explosion-proof and dust-proof. It has alarms that are visual, audible, and with vibration.
-
Product
Continuous Gas Analyzer
CT5400
-
Multi-component continuous gas analyzer combines QCL and TDL technologies in a single rack mount enclosure to measure process gas and monitor emissions from sub ppm to % levels. The CT5400 is ideal for measuring NOx, SO2, CO, CO2, CH 4, NH3, O2, HCl and other combustion gases identified as pollutants, ozone depleting, or responsible for global warming.
-
Product
Industrial Gas Springs – Push Type
-
Anyone who wants to lift or lower loads with control and without excessive strength relies on the industrial gas springs from ACE. These maintenance-free, ready-to-install machine elements, which are available from stock, support sheer muscle power, reliably open and hold.
-
-
Product
Gas Chromatograph Mass Spectrometer
GCMS-QP2010 SE
-
The Shimadzu single quadrupole GCMS-QP2010 SE gas chromatograph-mass spectrometer offers reliable, cost-effective productivity for the most challenging laboratory analyses, such as environmental and energy.
-
Product
Liquid Flow Meters
-
Alicat Scientific, Incorporated
Use liquid flow meters to measure liquid flow rates up to 100 kg/hr, with accuracy up to ±0.2% of reading or ±0.05% of full scale.
-
Product
Turbine Flow Sensor
2100
-
Engineered specifically for small diameter applications, the Signet 2100 Turbine Flow Sensor provides accurate readings in two flow ranges; 0.3 to 3.8 lpm and 3 to 38 lpm (0.1 to 1 gpm and 0.8 to 10 gpm).
-
Product
Greenhouse Gas Analyzer
GASERA ONE GHG
-
Many chemical compounds are present in Earth’s atmosphere and are capable of acting as greenhouse gases capable of absorbing and emitting infrared radiation emitted by Earth. Many of the gases such as carbon dioxide, methane, nitrous oxide and water vapor among others, occur naturally in the atmosphere and also have anthropogenic (man-made) sources. Methane (CH4) is the second most important greenhouse gas in terms of concentration and impact on the climate.
-
Product
Flue Gas Analyzer (Instrument Only)
C160
-
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C160 Residential Combustion Analyzer is instrument only, easy to use with a rugged design, multiple sensor protections and altitude compensation. Essential information for installing and maintaining furnaces and boilers all in one device.
-
Product
Gas Detection Controller
MX 43
-
Teledyne Gas & Flame Detection
Fully scalable, and designed to functional safety performance level 1 standards, the MX 43 is an analog and digital controller that continuously measures and controls gases in the atmosphere. The MX 43 gas detector manages both digital lines and analog channels, and covers all needs for a wide variety of gas monitoring applications. The MX 43 digital technology allows up to 32 detectors to be distributed on 8 lines for increased cost savings.
-
Product
Residual Gas Analyser For Process & Research
(QMS)
-
Quadrupole Mass Spectrometer Analyser System for low volume, quick responding gas measuring with large dynamic range Quadrupole Mass Spectrometer (QMS) for low volume, quick responding process gas measurement with large dynamic range.
-
Product
Flow Sensors
-
SICK provides innovative sensor solutions for flow measurement technology which combine flexible measuring methods and rugged equipment design with cost-efficient connection concepts to integrate higher-level systems. Whether you need to detect the current flow rate value using analog values or find the quantity using pulse detection – SICKs flow sensors are always reliable and safe and can work with a wide range of media under difficult process and ambient conditions.
