Parallel Digital Interfaces
-
Product
Ethernet To Parallel Digital Interfaces
-
ICS's 8063 Ethernet Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications.
-
Product
Ethernet To Parallel Digital Interfaces
-
ICS's 8063 Ethernet Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications.
-
Product
1.3 MP Custom Lens NIR Camera Module (Monochrome)
e-CAM10_CU0130_MOD
-
The e-CAM10_CU0130_MOD is a 1.3 MP NIR Camera module (Monochrome) based on the Aptina / ON Semiconductor AR0130CS CMOS image sensor with S-mount lens holder attached to it. The AR0130 is a 1/3” Optical Form factor, Electronic Rolling Shutter CMOS sensor with enhanced sensitivity in the Near Infrared region and superior low light performance. The e-CAM10_CU0130_MOD is designed to connect with any Application Processor that has parallel digital video interface. The standard S-Mount lens holder can accommodate a wide range of lenses based on the customer choice. e-CAM10_CU0130_MOD’s S-Mount holder can also house a fisheye lens or a zoom lens to meet their application requirements.
-
Product
Ethernet To Parallel Digital Interface Boards
-
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
Product
Wide Band Filters (multi-octave)
MINI-ERF® Series
-
The MINI-POLE® Extended Range Series of tunable filters was developed to address applications needing a small, surface mount package with wide tunability. This tunability is accomplished by the use of multiple internal tunable filters along with high performance PIN diode RF band select switches all contained in one housing. The tunable filters are designed to minimize size and power consumption while maintaining high RF power handling and linearity characteristics. Parallel or serial digital interface can be selected by a mode pin for ease of integration into your design.
-
Product
5.0 MP Custom Lens Camera Module (Monochrome)
e-CAM50_CU9P031_MOD
-
e-CAM50_CU9P031_MOD is a 5 MP custom lens monochrome camera module based on Aptina's MT9P031 CMOS image sensor with S-mount lens holder attached to it. The MT9P031 is a 1/2.5" Optical Form factor, Electronic Rolling Shutter CMOS sensor. The e-CAM50_CU9P031_MOD is designed to connect with any Application Processor that has parallel digital video interface. The standard S-Mount lens holder can accommodate a wide range of lenses based on the customer choice. e-CAM50_CU9P031_MOD’s S-Mount holder can also house a fisheye lens or a zoom lens to meet their application requirements.
-
Product
5.0 MP Custom Lens Camera Module (Monochrome)
e-CAM50_CU9P031_MOD
-
e-CAM50_CU9P031_MOD is a 5 MP custom lens monochrome camera module based on Aptina's MT9P031 CMOS image sensor with S-mount lens holder attached to it. The MT9P031 is a 1/2.5" Optical Form factor, Electronic Rolling Shutter CMOS sensor. The e-CAM50_CU9P031_MOD is designed to connect with any Application Processor that has parallel digital video interface. The standard S-Mount lens holder can accommodate a wide range of lenses based on the customer choice. e-CAM50_CU9P031_MOD’s S-Mount holder can also house a fisheye lens or a zoom lens to meet their application requirements.
-
Product
Camera Link Translators
CLT-303
-
The CLT-303R and CLT-303L Camera Link Translators convert RS-422 & LVDS to Camera Link, enabling the use of cameras incorporating traditional RS-422 and LVDS parallel digital interfaces with Camera Link frame grabbers. The “R” and “L” versions support RS-422 and LVDS cameras, respectively. These Camera Link converters are extremely flexible and can convert a wide range of cameras from parallel digital output to Camera Link base configuration with up-to 24-bit data.
-
Product
PXI-6529, 48-Channel, Sink/Source Inputs, Channel-Channel Isolated PXI Digital I/O Module
779949-01
-
48-Channel, Sink/Source Inputs, Channel-Channel Isolated PXI Digital I/O Module—The PXI‑6529 is an industrial, parallel digital input interface. PXI‑6529 devices are ideal for a variety of applications from automotive design, industrial factory automation, and machine control to aerospace, laboratory research, and biomedical applications. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6529 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
PXI-6528, 48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module
778543-01
-
48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module—The PXI‑6528 is an industrial, parallel digital I/O interface. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6528 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
PCI Bus Interface
PCI-6713-4IP
-
PCI Bus Interface 3.3 / 5 Volt via PLX 9056 33/66MHz High Performance Floating-Point DSP Up to 300MHz system clock. Up to 32Mbytes of SDRAM 4.0 Mbit flash memory for bootstrap program.
-
Product
PXI-8360, MXI-Express Interface, PXI Remote Control Module
779501-01
-
MXI-Express Interface, PXI Remote Control Module—The PXI‑8360 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCI‑8360 through a copper, x1 MXI‑Express cable.
-
Product
PCIe High Performance Host Adapter: Dual Port (x16), Gen 3
M9049A
-
The M9049A is a PCIe interface card for computers with PCIe expansion slots. It provides an extremely high performance link from an external computer to an AXIe or PXIe Chassis. The M9049A has a flexible configuration capability. Each card has two Gen 3 x8 PCIe cable links capable of achieving speeds up to 8 GB/s on each port. These two ports can be combined into a single x16 cable link providing a speed of up to 16 GB/s. This means a data-intensive system can be built using high-performance desktop or rack-mounted computers.
-
Product
SpaceWire PXI
318a
-
The SpaceWire PXI card is a versatile SpaceWire Interface, Router or RMAP target device. The card is designed to be an efficient host interface to a SpaceWire system or network, by utilising a cPCI or PXI backplane.
-
Product
Interface
RMAC-VME
-
Designed for laboratory simulation and production test applications, the Modular Avionics Controller (RMAC) is an intelligent, high performance 6U VME product supporting ARINC protocols and other serial communications. As an evolutionary follow-on product to the successful VME-AIC product line, the RMAC-VME provides a single integrated interface to multiple avionics protocols on VMEbus platforms.
-
Product
Interface
3508 MMS ECM
-
The 3508 Electrical Conversion Module (ECM) provides six (6) RS-232 outputs and ten (10) RS-232 inputs. Built around Maxim 1488 & 1489 chips for true RS232 levels and voltage tolerance, all outputs come up in the 1, mark or idle state. Electrically this is a negative output voltage, the start bit is always a 0 or a positive voltage level.
-
Product
High Performance PCI-GPIB Interface Card
82350C
-
Support fast transfer speeds for high data throughput and easily attach to low-profile PCs.
-
Product
PXI LIN Interface Module
-
The PXI LIN Interface Module is a bus interface for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LIN Description File (LDF) databases in integrated LIN databases. PXI LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
PCIe to PXIe Remote Control Interface Cable, 5m
43-921-500
-
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling. The 43-921 PCI Express-to-PXI Express expansion kit provides additional PXI instruments slots to the host computer by implementing a PCI Express-based control of PXI modules.
-
Product
Interface
RCNIC-A2PAU4
-
Abaco Systems' RCNIC-A2PAU4 is a high performance 4-lane PCI Express interface for monitoring, generating or analyzing full-bandwidth AFDX/ARINC 664 protocol traffic. Our exclusive pipeline architecture maximizes packet throughput using parallel controllers and efficient DMA transfers, thereby avoiding the bottlenecks of CPU-based interface solutions.
-
Product
Introduction to Graphical User Interface - Softpanel
61800 Series
-
The increased demand for Distributed Energy Resource (DR) products such as PV Inverter and Wind Energy systems, have increased the demand for regulation test standards to insure proper operation and safety of on-grid products. Manufacturers testing to prove compliance, need test equipment that can simulate and measure and test their products. Chroma’s 61800 family of Regenerative Grid Simulators provide a full 4 quadrant, regenerative, grid simulation for compliance, safety, and product verification testing
-
Product
PXI CANopen Interface Module
-
The PXI CANopen Interface Module is a high-speed CANopen interface for developing applications with the NI-Industrial Communications for CANopen driver. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation applications. The PXI CANopen Interface Module can transmit/receive PDOs and SDOs according to CiA DS301. It also features a batch SDO editor with electronic data sheet (EDS) file integration and layer setting services (LSS) support for slave node configuration.
-
Product
Interface Board, 16:1 USB
40-965-909
-
Converter card for 40-737-001 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 16 USB type A and 1 USB type B connectors. Allows the multiplexing of up to 16 USB1 or USB2 signals.
-
Product
Portable Avionics Interfaces for USB 2.0
-
These versatile interfaces are suitable for a wide range of applications in the lab and in the field. They support maximum data throughput on all channels and have a large 32 MB built-in memory. All power necessary for operation is provided via the single USB port. Plug and Play and Hot Swap features make them easy to install and move between computers.
-
Product
Interface
RCEI-830A
-
Designed for embedded, laboratory and simulator applications, the RCEI-830A supports maximum data throughput on all channels while providing onboard message scheduling, label filtering, multiple buffering options, receive message time-tagging and error detection, and IRIG-B receiver (AM or DC/TTL) and generator (DC/TTL).
-
Product
NI-5731, 40 MS/s, 12-Bit, 2-Channel Digitizer Adapter Module for FlexRIO
781657-02
-
The NI‑5731 is a digitizer adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a high-speed digitizer that simultaneously samples two channels at 40 MS/s. You can use the NI‑5731 to do real-time processing and streaming of analog data with high-performance A/D converters. The NI‑5731 also includes selectable elliptic, Bessel, and bypass hardware filters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 20 MS/s on 32 Channels
DN6.592-32
-
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 1 Channel (Single Ended) or 1 Channel (Differential)
M2P.5960-X4
-
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Avionics Test & Simulation Interfaces
-
Connect your PC laptop, desktop and tablet computers to avionics databuses with pocket-sized Ballard USB interfaces. Ease of use, versatility and comprehensive databus functionality have made these rugged adapters the industry favorite for avionics test, analysis and simulation in the lab and in the field. Avionics labs routinely integrate Ballard interface cards and full-featured network appliances into their test setups for powerful and reliable databus connection.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-Purpose Digitizer - 40 MS/s on 16 Channels, 16 Single-Ended Inputs
DN2.593-16
-
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
