-
Product
Inductor Coils
-
SemiGen's Inductor Coils are manufactured using our thin film process on quartz substrates. The precision photolithography and non-chemical etching process provides clean edges to assure uniformity from coil to coil. By using quartz and applying a polyimide coating we produce a device that eliminates the need for conformal coating or staking. Inductors can be epoxied down with nonconductive epoxy and the wire bonded for connection.
-
Product
Inductor Test & Packaging Machine
1870D
-
The Chroma 1870D Series (1870D/1870D-12) are specifically Designed automated test equipment for chip inductors. It comprises Various test functions that are required for verifying chip inductors. In addition, an automated tape packaging machine at the end of production line is equipped to fulfill demand for automated manufacturing.
-
Product
Inductor Products
-
Macom Technology Solutions Holdings Inc.
They provide uniformity, durability and repeatability in circuit fabrication. The coils are polyimide coated to protect from ambient contaminants, and to eliminate the need for conformal coating. Quartz substrates are rugged and reduce dielectric losses. Chips may be bonded using either conductive or non conductive epoxies, and wire bonded with gold wire or ribbon by thermocompression bonding.
-
Product
Power Inductor
-
Is a passive two-terminal electrical component that stores energy in a magnetic field when electric current flows through it.
-
Product
Power Inductor - Impulse Winding Tester
19301A
-
Chroma Systems Solutions, Inc.
The Chroma 19300 Impulse Winding Tester with high/low inductance test technology has 1000V of impulse voltage and a 200MHz high speed sampling rate that satisfies most power inductor test requirements for a wide range of inductance products from 0.1uH to 100uH. The built-in Area Size Comparison, Differential Area Comparison, FLUTTER value, and LAPLACIAN value functions are able to effectively inspect coils for insulation abnormalities.
-
Product
Switching Power Supplies
-
PeakTech Prüf- und Messtechnik GmbH
A type of power supply that works by switching current into a high-frequency transformer or inductor at frequencies much higher than the input or line frequency
-
Product
Surge Tester (Impulse Winding Tester)
SS6815 / SS6815F
-
Surge testers (impulse winding tester) is used for testing and check the insulation grade of turns between turns, insulation grade of layers between layers, insulation grade of windings between turns. It is used widely for transformer, current sensor, voltage sensor, relay, contactor, inductor, motor, generator, valve coil, voice coil, etc.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196C
Test Fixture
The 16196C surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Resistors and Inductors
-
Panasonic Automotive & Industrial Systems Europe GmbH
Our wide line-up of various Resistor and Inductor technologies supports the needs of the major industries such as Automotive, Industry, Telecom, HA and Medical markets. SMD, THT and axial shapes are available to support engineer's requirements.
-
Product
EMC Testing Inductors
-
Electromagnetic Compatibility (EMC) testing is a somewhat unique discipline within the world of electrical product development and analysis. Electromagnetic Compatibility (EMC) testing is primarily concerned with understanding and mitigating the affects of Electromagnetic Interference (EMI).
-
Product
LCR Meter, 1 MHz to 300 M/500 M/1 G/3 GHz
E4982A
LCR Meter
The E4982A LCR Meter provides the best performance for the passive component manufacturing such as SMD inductors and EMI filters, where impedance testing at high frequencies (1 MHz to 300 M/500 M/1 G/3 GHz) is required. Not only for the manufacturing, the E4982A can also be utilized for R&D, quality assurance with the powerful functions such as list measurements.
-
Product
Saturable Reactor Inductors
-
Osborne Saturable Reactors are designed to provide a variable output voltage through the use of variable impedance connected in series with a constant impedance load. Each saturable reactor’s impedance is determined by the application of DC power to a control winding. As the level of power supplied to the control winding is increased, the saturable reactor becomes more saturated. This reduces the impedance of the AC gate winding, and increase the amount of the supply voltage that is transferred to the load. Conversely, as the power is reduced to the control winding, the reactor becomes less saturated, the gate winding has more impedance and less of the input voltage is provided to the output impedance. This approach provides excellent quality, reliability, and control when designed to match the requirements of a specific application.
-
Product
32 Channel Pass Through Card
SET-2090
-
The input signals can be configured by customers. Each input channel can be tested, conditioned or measured in different ways. Various inductors, filters, pull-up or pull-down resistors can be used for this purpose. In standard configuration, the input signals are transmitted directly to the output.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
Test Fixture
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Programmable Inductance Decade Box
PLS Series
-
The PLS Series is a broad line of high precision programmable decade inductors. They provide straight inductance in a wide selection of ranges, tolerances andratings. IET Labs also supplies custom combination substituters for capacitance and resistance as well as sources for voltage and current.
-
Product
Atlas LCR Passive Component Meter
LCR40
-
The Atlas LCR40 automatically identifies and analyses almost any passive component (Inductor, Capacitor or Resistor). It measures its parameters using automatically selected test frequencies (DC, 1kHz, 15kHz and 200kHz).
-
Product
Bias T's
-
Centric RF offers Coaxial Bias T's so that a DC voltage can be applied to the rf signal path. These Bias Tee's (aka bias t) currently are offered with sma and 2.92mm connectors. Bias T's are implemented by attaching a broadband inductor to the circuit trace, with the power rating of the bias tee being determined by the size of the inductor.
-
Product
ISL911xx Family Of Buck-Boost/Boost Regulators
-
The ISL911xx buck-boost regulator family is capable of working with the ultra-small inductors and capacitors to fit within less than 14mm2 board footprint, making them the ideal 2A switching converter solution for space-constrained mobile devices. The advanced wafer-level CSP package requires only a single inductor and very few external components, which minimizes overall space requirements. The ISL911xx regulators’ 2.5MHz switching frequency further reduces the power supply solution size.
-
Product
Bobbin Winding Coil Turns Tester
SS108A series
-
Bobbin winding coil testers are used to test various coil of turns. Such as: generator winding turns, transformer winding turns, motor winding turns, inductor winding turns, contactor winding turns, relay winding turns, sparking winding turns, ignition winding turns, speaker voice coil, etc.
-
Product
LCZ LCR Meter
SS1062
-
This (SS1061 / SS1062 / SS1063) LCZ Meters are a test system for passive components designed for the use in electronic inspection or production process for quality control. They meet any demanding requirement on production speed and precision, discrimination of qualified products from unqualified ones, as well as internal setup, storing and calling function for up to 10 instrument groups, so they are actually optimum test instruments for component incoming and production inspection. Like as: transformer, inductor, resistor, capacitor, relay, motor, generator, eletric valve, contactor, cable, wire, etc..
-
Product
Drum Core Inductors
-
Drum core inductors are so named as the conductor (round magnet wire) is wound directly onto the ferrite core which is shaped like a drum or spool. The wire is then connected to the core, a plastic base or metal lead frame to form the surface mount termination. Drum core inductors come in unshielded (high saturation current but potentially more EMI) and shielded constructions (lower saturation current but closed magnetic path for lower EMI). The shielded constructions use either a second ferrite core or a magnetic resin epoxy to create the magnetic shield.
-
Product
Supply Chain Management
-
200 Customers100 Active SuppliersPurchasing for 60 material classifications including such materials as:a) IC, Resisters, Capacitors, Wire, Cable, Power Suppliesb) Connectors, Converters, Diodes, Fuses, Fabricated partsc) Inductors, Relays, Switches, Hardware
-
Product
Network Probe for TC-NT2
TC-TP1
-
TRENDnet´s TC-TP1 is an easy-to-use amplified inductor and tone probe that is used for tone tracing and line testing. The TC-TP1 features a simple push button that provides easy operation and conserves battery power. This ergonomically designed device comes with adjustable volume control and signal LED for enhanced accuracy in noisy environments.
-
Product
LCZ LCR Meter
SS1063
-
This (SS1061 / SS1062 / SS1063) LCZ Meters are a test system for passive components designed for the use in electronic inspection or production process for quality control. They meet any demanding requirement on production speed and precision, discrimination of qualified products from unqualified ones, as well as internal setup, storing and calling function for up to 10 instrument groups, so they Like as: transformer, inductor, resistor, capacitor, relay, motor, generator, eletric valve, contactor,cable,wire,etc.
-
Product
Alternate Constructions
-
In addition to Power Beads, Molded & Composite, Drum Cores and Round Wire Coil Inductors Pulse also designs and manufacturers multiple other constructions for catalog and custom solutions.
-
Product
LCR Meters
-
PeakTech Prüf- und Messtechnik GmbH
A type of electronic test equipment used to measure the inductance (L), capacitance (C), and resistance (R) of an electronic component.[1] In the simpler versions of this instrument the impedance was measured internally and converted for display to the corresponding capacitance or inductance value. Readings should be reasonably accurate if the capacitor or inductor device under test does not have a significant resistive component of impedance. More advanced designs measure true inductance or capacitance, as well as the equivalent series resistance of capacitors and the Q factor of inductive components.
-
Product
Decade Boxes
-
Transcat stocks the decade boxes for your precision measurement applications. Using a series of resistors, capacitors or inductors, a decade box simulates electrical values. Switches are arranged in decades (sections of 10) where values from 0-9 are selected. Configured boxes can be substituted into a circuit as a component to determine the appropriate value for circuit operation. They can also be connected to input devices for testing. After connection to the decade box, a device should display a reading corresponding to the previously set box value. Our wide selection of decade resistance boxes include models that can serve as standards in verifying the accuracy of resistance-measuring devices. We offer a wide variety of boxes built by IET Labs, Prime Technology and AEMC.
-
Product
Filter Design Software
QuickFil
-
QuickFil is a software for designing passive electronic filters. The result is an optimized circuit of inductors (L)and capacitors
-
Product
Bias Tee's
-
A bias "T" consists of a feed inductor to deliver DC to a connector on the device side and a blocking capacitor to keep DC from passing through to the receiver.
-
Product
µModule Isolated Transceivers
-
Analog Devices µModule (micromodule) isolated transceivers provide robust galvanic isolation for digital serial communication interfaces, including SPI, I2C, RS-485/RS-422, RS-232, and USB. Isolation barriers are implemented using Ethernet transformers, coupling capacitors, or embedded inductors. All devices are simple to configure, have very low EMI susceptibility and emissions, and feature high noise immunity to preserve signal integrity.
