Switches
enable on off function or change of direction.
See Also: Membrane Switch, Coaxial Switches, Crossbar, High Voltage Switching, Fiber Optic Switching, Microwave Switching, Optical Switch
-
Product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m, HV
A037DF4-C-HA050
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Wind Speed Sensor/Anemometer
ENVIROMUX-WSS
-
Rugged anemometer. 3-cup rotor pressed on a stainless steel shaft. Reed switch and magnet providing one pulse per rotation. Rotor diameter: 5 inches. Speed range: ~ 3 mph to 125+ mph (~5 kph to over 200 kph). Rugged Delrin body with bronze and Rulon bushings. Flat aluminum mounting bracket with 2 holes. esigned to be mounted on top of a pole or bracket. 100 feet of exterior grade wire. Maximum cable length: 1000 ft (305m).
-
Product
Tap Changer Analyzers & Winding Ohmmeters
-
Winding resistance test of inductive test objects, such as power transformers, is one of the most effective non-intrusive ways of checking its condition. Due to their advanced design, DV Power winding resistance meters provide high test currents (up to 100 A DC) and high accuracy (up to 0.1%) within light and portable test instruments. In addition to winding resistance measurement, it is also possible to perform simple, quick and reliable transformer on-load tap changer condition assessment by recording the test current during tap changer operation, also known as DVtest. Because of that, problems with a tap changer connection, contacts, and switching procedure can be detected.DV Power winding ohmmeters consist of single-phase RMO-T and three-phase TWA series. Models from the TWA series are designed for six-winding resistance measurement of power and distribution transformers, with only one single-step cable setup. As a result of reducing the total test time, it enables significant saving of time and money.Typical application areas of these instruments are high-voltage substations and industrial environments. They are intended to measure the resistance of:Transformer windingsOn-load tap changersGeneratorsElectrical motorsHigh-current bus bar jointsCable splicesWelding joints
-
Product
PXI 16 x DPST Reed Relays
40-115-022
Relay
This is the 16xDPST version of our 40-110/40-115 range of reed relay switching modules which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector.
-
Product
PXI 8 Slot BRIC 20x32 1-Pole (4 sub-cards)
40-562A-121-20X32
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Photoelectric Switch
PE3
-
● Compact size for 13.5(W)*25.5(H)*32.0(L)● A wealth of models ideal for limit control, counting control, and other applications.● Sensing distance of 5~60cm for Diffuse reflective models, 1M~2M for Retro reflective models and 1M~5M for Through beam models.
-
Product
Pressure Switches
-
NOSHOK offers a wide selection of mechanical and electronic pressure switches, including low pressure, compact switches with 1 SPST N.O. or N.C contact, as well as RoHS compliant SPDT pressure switches with adjustable hysteresis. These switches are ideal for use in hydraulic systems including mobile hydraulics, as well as pneumatic systems, power generation, industrial machinery or machine tools, pumps & compressors and more.
-
Product
HD 8 Line Crosshair / Line Generator
CL8800
-
The CL8800 has four X and four Y moveable lines. The lines can be set to black or white and each line can be turned off or on individually. Lines may be changed from solid to serrated with one of many lines styles. A lock switch is provided for each of the four controls to prevent accidental movement.
-
Product
LXI 16:1 Optical MUX FC Loop-Thru
60-850-423
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
PXI 8 Slot BRIC 270x8 2-pole (9 sub-cards)
40-561A-122-270X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
4 Discrete/Switch I/O Channels (±100 V, 3 A/Ch.)
DT3
-
The DT3 module (the enhanced version) feature 4 independent, high current, isolated, programmable channels that can be used for input voltage measurements (±100 V), or as a bi-directional current switch (up to 3 A per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection.
-
Product
MANUAL TEST FIXTURE KITS
SERIES 5590
-
Built with unique design features: Ease of assembly and disassembly All side panels are removable Side panel material is delrin for easy machining for connectors, switches etc.Light weight and durable construction2" Between Probe plate and lid plate allowing more room for tall board components
-
Product
Circuit Breaker Testing
-
HAOMAI Electric Test Equipment Co., Ltd.
Circuit Breaker Testing is utilised to test the operation of each switching systems and the programming of the entire tripping structure.
-
Product
Ultra Slim DIN Rail AC-DC Power Supplies
DPC Series
-
XP Power today announced the DPC series of highly efficient ultra slim DIN rail AC-DC power supplies. Available in 30, 50 and 70 Watt single output models, they all accept the universal input range from 90 to 264 VAC without the need for any input selector switches. Taking up significantly less space on the rail by being up to 44% slimmer than current generation DIN rail power supplies, the 30 Watt DPC30 measures just 90.0 x 100.0 x 22.5 mm (3.6 x 3.94 x 0.89 inches). Also, the 50 Watt DPC50 measures 90.0 x 100.0 x 30.0 mm (3.6 x 3.94 x 1.18 inches) and the 70 Watt DPC70 measures only 90.0 x 100.0 x 40.5 mm (3.6 x 3.95 x 1.59 inches). Offering all the popular nominal output voltages from + 5 to + 48 VDC, the single output can be adjusted up to + 30% of stated nominal, model dependant, in order to accommodate non-standard voltage requirements or to make up for line losses. All models feature a green LED to indicate output on.
-
Product
PXI BRIC8 1Resource Distributor, 1Bus Matrix
40-569-111
Matrix Switch Module
The 40-569 PXI Matrix BRIC provides a range of high-density bus matrix inputs and resource distributor bussed configurations capable of switching up to 2A and up to 100VDC/70VAC. These large PXI matrix modules are available in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays.
-
Product
PXI 16x4 RF Matrix 300MHz 50 Multiway Connector With Loop-Thru
40-727-002-L
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode, 9/125 Fiber, FC/PC Connectors
40-852A-118
Multiplexer Module
The 40/42-852A-118 is a PXI/PXIe 8-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
1x8 Multiplexer Plug-In
1260-138A
Multiplexer Module
The Astronics1260-138A is an eight 1x8, two-wire scanner/multiplexer plug-in card for the Adapt-a-Switch® platform. It installs, easily and directly from the front panel, into the Adapt-a-Switch VXI Carrier, 1260-100.
-
Product
PXI 8 Slot BRIC 180x16 2-pole (12 sub-cards)
40-561A-122-180X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Quad 4 to 1 Mux 1.3GHz 50Ohm SMB
40-749-511
Multiplexer Module
The 40-749 is a quad 4 to 1 RF MUX available in 50 Ohm or 75 Ohm versions occupying a single PXI slot. The module is available with SMB or SMA connectors for 50 Ohm versions or, 1.0/2.3 or Mini SMB connectors for 75 Ohm versions. Applications for the 40-749 include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching, video/audio switching and switching high frequency logic signals.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 13-Bank 6GHz SMA
60-802-013
Multiplexer Module
The 60-802-013 is a 4-channel, 13-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
Human Machine Interface
HMI
-
Ducommun has designed and manufactured Human Machine Interface (HMI) illuminated switches, keyboards, and lighted panels for a diverse array of military and commercial applications. Platforms include the most modern military fighter and transport aircraft, commercial airplanes, helicopters, military ground vehicles, control systems, shipboard, and space applications. Ducommun is a trusted name in the industry for best-in-class product reliability with a deep heritage of success on demanding programs.
-
Product
PXI/PXIe High Density 2A Multiplexer, 2-Bank, 8-Channel, 8-Pole
42-614D-013
Multiplexer Module
The 40-614D-013 (PXI) and 42-614D-013 (PXIe) 2-bank, 8-channel, 8-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 5-Bank 18GHz SMA
60-802-205
Multiplexer Module
The 60-802-205 is a 4-channel, 5-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-310-010
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
PXI 2 Amp MUX, Single 16-Channel 2-Pole
40-635-102
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
Micro OHM Meter
-
Cambridge Instruments & Engineering Co.
This Test set is capable to measure low resistance like switch contacts, breaker contacts, busbar slices, joints, fuses, low inductive windings etc.
-
Product
Transformer Winding Resistance Meters
RMO TD Series
-
The RMO-TD Series On-Load Tap & Winding Resistance Analyzer is designed for the measurement of winding resistance of inductive elements, and for tap changer analysis. The RMO-TD series is based on the latest technology, using the most advanced switching technology available today. The RMO-TD series is accurate (0.1%), powerful (up to 60 A) and lightweight. It generates true, ripple-free DC current with automatic metering control and a discharge circuit.
-
Product
Stepper Motor,Precision Linear Stages,Application for Labs
PSAXXX-11-X
-
Model:PSAXXX-11-X Stepper Motor,Precision Linear Stages,Application for Labs Stepper motor and RS232 interface combine with SC300,MC series controller, achieve automatical control. Grinding ball screw ,linear slide and elastic couplings adopt high-quality products ,provide quality assurance . The design of limited switches and zero switch protect products and supply convenience;Standard interface is convenient for singal’s output. The back of motorized stages has handwheel , it is for convenience for adjustment; Standard hole is so easy for combine with other units, ensure convenience for multi-dimensional system; standard stepper motor and DB9 interface, choose to any controller according to requiremment
-
Product
Handheld Ultrafine Particle Size Distribution Measurement.
partector 2 Pro
-
Naneos Particle Solutions gmbh
The naneos partector 2 Pro version is a further development of the well-established Partector 2. The Pro version of the partector 2 can additionally switch through different deposition voltage levels and therefore scan an 8-channel size distribution of an aerosol of interest.
