PCB
See Also: Printed Circuit Board, PCBA, Crosstalk
-
Product
Mini SMP Connectors
-
Mini SMP connector series, also known as SMPM connectors, are ultra-miniature, high frequency connections commonly used in applications up to 65 GHz. Mini-SMP connector category will terminate to coax or PCB (printed circuit board) and many mini-SMP connectors are hermetically sealed. Pasternack mini SMP connectors are built to precise microwave and RF industry specifications and many are RoHS and REACH compliant. SMP mini connector products are built in male or female gender with 50 Ohm impedance. Mini-SMP connectors are available in straight or right angle versions, as well as, mountless options. These Mini-SMP connector designs include solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave components from Pasternack are in-stock. Not only in stock, but these SMP mini connectors will ship the same day as they are purchased.
-
Product
500-Pin SEARAY Connector, Male with Backshell, 1 Amp, 500 Port
C500RMR-4SB-0A
SEARAY Male Connector
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This accessory is designed to allow users to directly terminate a cable via solder bucket connections to a PCB linked to a 500-Pin SEARAY connector. Pickering Interfaces recommend the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to NI PXI-2529 with six 36" cables
510150154
PCB Adapter
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to NI PXI-2529 with six 36" cables
-
Product
Positional Current Probe, PCB Track Touch And Measure
I-prober 520
-
Current measurement from insulated probing of conductorSuitable for observation and measurement of current in PCB tracks, component leads and ground planesWide dynamic range of 10mA to 20A peak to peakWide bandwidth of DC to 5MHzLow noise figure equivalent to <6mA rms at full B/WSafety rated to 300V Cat II (600V Cat 1)Suitable for connection to any oscilloscopeHigh accuracy general purpose H-field probeConverts to 'closed magnetic circuit' current probe
-
Product
SparkFun RJ45 Breakout
-
RJ45 connectors are the kind that are used for Ethernet jacks, but they make great general purpose connectors when you need a lot of conductors. This is a small PCB that brings out the pins of the RJ45 connector to an in-line 0.1" footprint. Use with break-away headers for breadboarding or create your own RJ45 cable. Check the related items for Ethernet cable and connectors to go with it!
-
Product
SSMA Connectors
-
Pasternack SSMA connector category includes 52 part numbers, most are RoHS and REACH compliant. SSMA connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Pasternack SSMA connectors are built to precise microwave and RF industry specifications. Connectors in SSMA series are manufactured in male or female gender with 50 Ohm impedance. SSMA connector items are available in straight or right angle versions, as well as, bulkhead, 2 hole panel, 4 hole panel or mountless options. These SSMA connector designs include crimp/solder, solder, solder (without contact) or solder/solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this SSMA connector series is in-stock. Not just in stock, but these connectors will ship the same day as they are purchased.
-
Product
PCB High Sensitivity, 100mV/g, ICP® (IEPE) Accelerometer
784170-01
-
The PCB HSTA15 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB HSTA15 features a sensitivity range of 10 mV/g and requires a 4-socket plug-to-3 BNC plug cable.
-
Product
BME680 Environmental Sensor
28061
-
Raise your project’s environmental awareness with the BME680. The Bosch Sensortec BME680 Integrated Environmental Unit combines a gas sensor with air pressure, humidity, and ambient air temperature sensing functions within a single package for high performance air quality measurement. Parallax Inc. places the BME680 on a compact PCB with a 6-pin male header. This capable sensor does not have to be difficult to use. The BME680 is supported by BlocklyProp visual programming as well as C libraries for the Propeller multicore microcontroller. Code for other controllers is available from the Bosch Github repository.
-
Product
37-Pin D-Type Male Right Angled PCB HV
40-963-037-RM-HV
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
78-Pin D-Type Female Straight PCB Mount
40-963-078-SF
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
In-Line RF Test Station
AP770
RF Test System
ICT, Functional, Hipot, Vision, ISP and RF test with low cost fixtures in a very compact test station footprint Works with PCBs up to 450×550 mm or with palletized devices Space for up to 25 VPC mass interconnect modules or YAV switching units
-
Product
37-Pin D-Type Male Right Angled PCB
40-963-037-RM
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
PCB Adapter, ITA, SIM, VTAC, 32 Pos, 6 Slot, to (1) DisplayPort
510171116
PCB Adapter (ITA)
PCB Adapter, ITA, SIM, VTAC, 32 Pos, 6 Slot, to (1) DisplayPort.
-
Product
PCB Adapters - SIM
-
SIM PCB Adapters provide flexibility and modularity where custom PCBs cannot. Mix and match small modular boards to create a custom solution. Move SIM PCB adapters around to optimize space, mix protocols and match with patchcords. Combine protocols in a VPC SIM module and swap boards as your requirements change.
-
Product
Module Spectrum
nRF52832 Series
-
Raytac nRF52832 module spectrum covers MDBT42Q, MDBT42 and MDBT42V series with both Chip Antenna and PCB Antenna option for selection.
-
Product
OEM 1-Channel Fiber Optic Signal Conditioner PCB Module
FOTEMP1-OEM-MNT
-
The FOTEMP1-OEM-MNT is a small form factor PCB interface module designed for low cost insertion of high precision GaAs-based fiber optic temperature sensor technology into OEM applications where common electrical temperature sensors and thermocouples cannot be used. The OEM interface product is compatible with all TS series fiber optic temperature probes. The sensors are entirely non-metallic and electrically passive, providing immunity to EMI, RFI, MR, microwaves and radiation is required.
-
Product
VTAC, Insert, Receiver/ITA, SIM, Right Angle, 8 Pos, 1 Slot
610151104
SIM Insert
This insert contains 8 right-angle VTAC high speed contacts and is designed to mount directly to a PCB as part of the Infinity Connector system. It is used in the 90 Series SIM Module and occupies 1 of the 34 slots in this module. Available in a set with VTAC pass-thru insert as 610151106. Use the video link on this page for help installing this insert on a PCB.
-
Product
15-Pin D-Type Connector, Male
40-963-015-SM
D-Sub Male Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 15-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
High Force Type Prbobe For PCB, K100 Series 100 Mil Pitch, Receptacle With Wire Wrap Pin
KR100-WP
Spring Probe
K100 Series, Pitch 100mil, Receptacle, with wire wrap pin. Brass with gold finish.
-
Product
48-Ch SPDT 1A-100VAC 24VDC Switching
YAV91074
Relay
The YAV90074 module contents 48 SPDT Relays independent. Each relays PCB contact track is shielded individually in order to handle very low voltage signals and audio signals with extremely low crosstalk. The build-in power supply includes two extra filters to reduce the DC voltage ripple to the relay coils; the control tracks have been drawn in quadrature with signal ones, reducing the inductive coupling produced by the transient current.
-
Product
ITA, G18, 18 Module With Discrete Wiring And PCB Capability
410120101
ITA
ITA, G18, 18 Module with Discrete Wiring and PCB Capability
-
Product
High Force Type Prbobe For PCB, K100 Series 100 Mil Pitch, Receptacle
KR100
Spring Probe
K100 Series, Pitch 100mil, Receptacle, no wire wrap pin. Brass with gold finish.
-
Product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 4 or 10 Positions Blocks, UUT 586 x 248 mm
MG-03-01
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 586 x 248 mm (wxd)• Outer dimensions: 750 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 8 interface blocks of 160 or 170 signals• All interface blocks can be customized
-
Product
Controlled Impedance Analyzers
-
HYPERLABS Controlled Impedance Analyzers can be used with various probes and adapters to quickly and reliably characterize impedance on PCB test coupons. These Test Systems are designed to comply with IPC-2141A standards for PCB coupon testing, and can be customized to meet specific customer needs.
-
Product
Cryogenic Applications
-
Over the last 20 years the Celadon Engineering team has developed an expertise in cryogenic materials which has resulted in a solid reputation in the industry for producing extremely stable cryogenic on-wafer probe card as well as DUT probing solutions. These custom cryogenic probe card solutions are widely used to test Space, Military, Medical and Quantum Computing products. Celadon’s cryogenic solutions vary from standard VersaTile™ footprints which interface to positioners to innovative custom PCB based designs to allow for flexibility when testing at these very cold temperatures. Lakeshore cryogenic wire is used in standard DC solutions for high density cableout designs to support high pin count applications. During the development process, Celadon works closely with the cryogenic prober vendor to ensure the integrated solution is optimized for current and future testing needs.
-
Product
96-Pin SCSI Micro-D Straight PCB
40-963-096-SM
SCSI Male PCB Mount
Ideal for user created termination schemes where the termination is to be on the front of the product or remotely connected to the module by cable. Suitable cables for this product are detailed in the data sheet. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
PCB Connectors
HDLP Series
-
Smiths Interconnect's HDLP series is a low profile, high density interconnect with integral sealing
-
Product
Custom PCB Enclosures
Enclosure
Our customers have shared a long history of using printed circuit boards (PCB) in the interchangeable test adapters (ITAs) of their automated test equipment (ATE) stations. Whether you are designing a self-test fixture and want to save space, improve signal integrity, and/or reduce cable management headaches, VPC has a team of engineers with the expertise needed to help.
-
Product
In-Circuit ESR & DCR capacitor Tester
236
-
This In-circuit ESR & DCR capacitor tester is designed to measure ESR (equivalent Series Resistance) on capacitors range from 0.47uF to 2200uF, in or out of circuit. The ability to trouble shoot in-circuit saves time and makes the 236 a must for anyone that tests or trouble shoots PCB (printed circuit boards).
-
Product
RF Radio - Frequency Probes
-
*3 to 6 Ghz *PCB MCX SMB SMC *SMA U. FL MS / MM Fakra *Exchangeable inner plunger
