Bridge Amplifiers
Increase a transducers signal to measurable levels.
-
Product
Motion Control Terminal Board For Mitsubishi J2S-A Servo Amplifiers
DIN-812M0
Terminal Board
- On-board connector type: 100-pin SCSI-II female- Suitable for Mitsubishi J2 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8132
-
Product
2-22 GHz GaAs MMIC Traveling Wave Amplifier
HMMC-5022
Amplifier
The HMMC-5022 is a broadband GaAs MMIC traveling wave amplifier designed for moderate gain and moderate output power over the full 2-22 GHz frequency range. Typical applications of the HMMC-5022 include wideband gain blocks of communication systems and microwave instrumentation, which require a flat gains response and excellent port matches over the 2-22 GHz frequency range.
-
Product
Analog Summing Amplifier
SIM980
-
Stanford Research Systems, Inc.
The SIM980 Summing Amplifier has four input channels that can be added or subtracted from each other. The output noise is less than 60 nV/√Hz, and crosstalk between channels is less than -80 dB. With a bandwidth of 1 MHz, a slew rate of 40 V/ms, and input offsets that are trimmed to ±100 µV, the SIM980 is extremely useful in many analog applications.
-
Product
Resistance Bridges - AccuBridge® Line
-
Measurements International Ltd.
The Resistance Ratio Bridge from Measurements International is the next generation replacement. Measurements International is pleased to release the next generation room temperature Direct Current Comparator Resistance Ratio Bridge.
-
Product
Four Quadrant Power Amplifier
PAV3000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
Dual Channel High Voltage Linear Amplifier
A800D
-
This unit contains two independent A800 amplifiers that share common ground reference and power supply.
-
Product
Standard Signal Isolating Amplifier
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Isolation and conversion of standard signals. Calibrated switchable inputs and outputs 0/4 ... 20 mA and 0 ... 10 V signal duplicator with two electrically isolated outputs.
-
Product
Motion Control Terminal Board For Panasonic MINAS A4 Servo Amplifiers
DIN-814-A40
Terminal Board
- Panasonic MINAS A4 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134
-
Product
HF Low Noise Amplifier
-
The COMM-connect HF Low Noise Amplifier can be used to amplify signals in the HF frequency range. The amplifier comes with a selection of 4 different connectors, which makes it very easy to adapt to any type of installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
-
Product
Optic Node With Amplifier
OX 755
-
Converts even weak Optic Signals to a high quality RF Signal. LED BAR Optic Level Display has been provided for ease of system maintenance. They are best suitable for Analog as well as Digital transmission to maintain BER, MER Characteristics.- High Quality Nodes cum Amplifier- Frequency 40 ~ 1000 MHz- Good Sensitivity of -11 dBm- RF O/P 110 dBµV at 0 dBm Optic I/P- High Voltage Surge Protection- LED Optic Level Display- Powder Coated Housing
-
Product
High-Voltage Amplifiers - to 1000 Volts peak-to-peak
-
These amplifiers provide high amplitudes and bandwidths, and are well suited for use as booster amplifiers for lower-voltage arbitrary waveform generators.
-
Product
Monolithic Balanced Mixers With Intermediate Frequency Amplifier
-
Insight Product Company offers Monolithic Balanced Mixers with and Intermediate Frequency Amplifier in frequency range of 26 to 178 GHz.
-
Product
Fully Differential SD Video Filter Amplifier With Output Short-To-Battery Protection
ADA4433-1
-
The ADA4433-1 is a differential output, fully integrated video reconstruction filter that combines overvoltage protection (short-to-battery [STB] protection) and short-to-ground (STG) protection on the outputs, with excellent video specifications and low power consumption. The combination of STB protection and robust ESD tolerance allows the ADA4433-1 to provide superior protection in the hostile automotive environment.
-
Product
Switching Amplifiers
-
*One- or two-channel design*Small design requiring only very little space*Programmable output function*Relay or transistor outputs*Easy mounting on DIN rail
-
Product
Communications/Data Link Amplifiers
-
Amplifiers specific to the Communications systems include a wide range of Solid State Power Amplifiers (SSPAs) and Low Noise Amplifiers (LNAs) originally from Paradise Datacom and a range of organically developed products within TMS. Satcom SSPAs are considered a core competence of Paradise Datacom's product line who have invested heavily in converting it's complete amplifier offering from GaAs to GaN from C-Band all the way to Ka-Band.
-
Product
Broadband Power Amplifier
PAS-00260-10
-
* Solid State Power Amplifier* Gain : 49 dB typ.* High IP3, 50.0 dBm typ.* Bench Top Case* Internal Cooling Fans* Type N Connectors
-
Product
Ultra-broadband Power Amplifier Systems
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink provides ultra-broadband power amplifier systems in rack-mounted configuration with output power capacity from 50-Watt to 2000-Watt for applications including EMC testing, communications, and TWT replacement.
-
Product
Low-Noise Parametric Amplifiers
-
Insight Product Company offers Low-Noise Parametric Amplfiers based on Monolithic Integrated Circuits (MIC) in the frequency range of 30 to 100 GHz.
-
Product
Gain Shape Linearizer Amplifiers
-
Gain Shape amplifiers are used in a number of applications where it's necessary to flatten the gain characteristic of the preceding or following component. This would include flattening the attenuation of a long cable run or perhaps changing the input gain response to a MPM (Microwave Power Module) or TWT (Traveling Wave Tube) to compensate for the gain variation within the tube.
-
Product
Power Amplifiers
-
The RF power amplifier range from Laplace is specifically designed for EMC Immunity testing according to IEC61000-4-3 and IEC61000-4-6. These are compact units with characteristics matched to the requirements of IEC standards. These RF amplifiers utilize fully isolated linear MOSFET or advanced GaAs FET devices, which provide high gain, wide dynamic range and excellent third order intercepts. High efficiency and reliable operation are achieved by employing unique RF combining circuits, RF microstrip networks, sophisticated thermal design, custom machined housing and heavy duty components. The high power RF amplifiers undergo extensive burn-in prior to final test and inspection.
-
Product
RGB 1×3 Video Distribution Amplifier
VDA403
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.The second application is when the video signal is run over distances greater than 50 feet. The coaxial cable has a fair amount of signal loss over long distances. When multiple monitors are connected after long runs of coax, the degradation can be severe, especially when dealing with modern, high bandwidth signals that have 500+ lines of resolution.The VDA403 is a Video Distribution Amplifier designed for professional applications. It will operate with NTSC & PAL video signals as well as many common Black & White signals. These units use the latest integrated amplifier technology for superior performance and reliability. Custom units or modifications can be manufactured at a reasonable cost.
-
Product
Microwave Power Amplifier 1/4 Watt, 10 MHz to 40 GHz
GT-1040A
-
The Spanawave/Giga-tronics GT-1040A Microwave Power Amplifier incorporates broadband MMIC-based architecture. These state-of-the-art amplifiers are based on solid-state parallel MMIC design with exceptionally wide bandwidth and high power. The unique circuit topology is highly reliable, with performance that excels where extremes of bandwidth and power are demanded.
-
Product
EDFA Optic Amplifiers
-
Wuhan Sunma Technology Co., Ltd.
With the feature of high input power, high output power, and medium optical gain, the booster amplifier operates at the transmission side of the link to amplify aggregated optical input power for reach extension.SunmaFiber booster amplifier is a low-noise, gain-flattened C-band optical erbium doped fiber amplifier (EDFA) designed to cost-effectively extend the optical link power budget for building long distance DWDM solutions.SunmaFiber also offers switches, routers and fiber converters including 10/100M, 10/100/1000M and 10G fiber converters, SFP fiber converters, manageable/unmanageable fiber converters, OEO fiber converters, POE fiber converters, fiber converter cards, and fiber converter chassis; transmitting distance from 2km(MM) to 150km(SM) with SC or LC or FC connectors.
-
Product
Bridge Decking Testing Equipment
-
The testing process can detect blow holes, inclusions or thin areas in 'sprayed-type' membranes. Because the concrete contains a small amount of water, it is electrically conductive and a DC Pinhole Detector can be used to create a high voltage which is passed over the surface by the use of a brush electrode. An alarm will sound to identify any small defects which can be rectified so that the integrity of the coating can be verified.
-
Product
Fiber Optic Sensor & Amplifier
FG-1300 | FS-5500/FS-540
-
The FG-1300 is a non-contact type high-performance amplifier that emits red light from LED to a rotating object, and detects the variation of the reflected red light amount.This amplifier is used in combination with an exclusive detector FS-5500*/FS-540 Fiber Optic Sensors which has adopted environment resistant design. The glass fibers are covered with flexible stainless steel tube for rotation measurement in limited space.
-
Product
Crossed-Field Amplifiers
CFAs
-
Communications & Power Industries
CPI BMD’s crossed-field amplifiers (CFAs) are broadband, phase-stable microwave amplifiers used in coherent radar chains to efficiently generate very high peak output powers from relatively low input voltages which can be either applied to the cathode or an electrode similar to a TWTs cathode or grid pulsing, and in relatively small, lightweight packages. These characteristics make CFAs particularly well-suited for applications in which the transmitter must be either airborne, transportable, mobile or portable.
-
Product
Amplifiers
-
Computer-controlled charge amplifier module features variable gain and output scaling and accepts either differential or single-ended inputs. Adjustable parameters include: accelerometer sensitivity, differential or single-ended mode, scaling, filter setting, external calibration and zero mode.
-
Product
DR Range Broadband Power Amplifiers 10 KHZ - 400 MHZ
DR Series
-
Class A solid stateBroadband (instantaneous single band): 10 kHz 400 MHzTypical output power : 60 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 40 W and H<-20 dBc up to 250 MHz andP1dB > 25 W and H<-20 dBc from 250 MHz to 400 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Low Noise Op Amplifiers (≤ 10nV/√Hz)
-
Analog Devices’ portfolio of low noise (≤ 10nV/√Hz) op amps includes many amps with the lowest noise performance in the industry. These high speed, low distortion (1 nV or less) op amps enable better signal fidelity in the most demanding conditions, allowing system designers to achieve the lowest total system noise performance in applications with high source impedances. We feature a considerable variety of these amps with wide supply ranges and low power.
-
Product
1 kHz Automatic Capacitance Bridge
AH 2500A
-
The AH 2550A offers unparalleled stability, resolution and accuracy in a capacitance/loss bridge (whether manual or automatic). Its numerous state of the art features make it an exceptionally user-friendly instrument, just as was its predecessor, the AH2500A. The precision and ease of use of the AH2550A are creating new applications in science, calibration, and production in a wide range of fields.
