-
product
Modbus Controllers
Datexel has a range of Modbus RTU Masters, Slaves, Controllers, Data Loggers and Modbus remote displays. The DAT9000 is a Modbus RTU Master with RS485, RS232 and Ethernet Interfaces. The DAT9000IO is similar to the DAT9000 but it has digital input and outputs. The DAT9000DL has an additional Data Logging facility and the DAT9000DLIO has both Data Logging and digital IO. The DAT9011 is a Modbus Master with 2 analog inputs which can chose from Thermocouple's, RTD's, Potentiometers, mA and mV's. It also has 2 outputs which can be mA or voltage. The DAT9011 can also accept digital inputs and provide 2 SPDT relay outputs. The DAT9011DL also has a Data Logging facility which can store up to 8gb of readings on a thumb drive.
-
product
PXI 25 x DPST Electromechanical Relays
40-146-002
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
product
ECAT MiniModules
XCP-Gateway
XCP-Gateway is the interface between the data acquisition software (e. g. vMeasure, CANape®, INCA®, Vision® ...) and the EtherCAT® measurement modules from CSM. It includes an EtherCAT® master and an XCP-on-Ethernet slave. CSM developed the XCP-Gateway for the ECAT MiniModule series and for measurement applications with many measurement channels and high measurement data rates.
-
product
PXI 75 x SPST Ruthenium Reed Relay Switching
40-140A-121
This range of high density reed relay switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.).
-
product
3.4 MP Autofocus (Liquid Lens) Low Light Camera Module
e-CAM31_MI0330_MOD
e-CAM31_MI0330_MOD is a high performance, small form factor, 3.4 MP Autofocus Low Light Camera Module with Liquid Lens. It is based on AR0330 CMOS Image sensor from ON Semiconductor®. This Autofocus Liquid Lens Camera Module has slave mode for precise frame-rate control and for synchronizing two sensors. e-CAM31_MI0330_MOD – Liquid lens camera module has superior low light performance. It supports Full HD @ 60fps for maximum video performance. It also has a support for external mechanical shutter and an on-chip phase-locked loop (PLL) oscillator. The dedicated ISP performs the entire Auto functions like auto white balance, auto exposure control in addition to complete image signal processing pipeline.
-
product
Programmable Modbus slave Simulator
ModSlaveSim
ModSlaveSim is a programmable simulator that enables realistic simulation of a Modbus slave in its environment. Connect your Modbus masters to ModSlaveSim, instead of a real Modbus slave device, in order to test and configure the masters.
-
product
EOC Slave
EOS-102/EOS-104
Hangzhou Softel Optic Co., Ltd.
EOS-102/EOS-104 is the EOC slave based on HomePlug AV solution for Ethernet access over coax. It works together with EOC master which is based on HomePlug AV solution as well to construct a two-layer Ethernet data transmission channel on CATV coax cable, provide the Ethernet access service based on the existing coax cable networking. EOS-102 is slave with 2 Ethernet ports while EOS-104 is the one with 4 Ethernet ports .
-
product
GPS Synchronized Clock Systems
Signals & Systems India Private Limited
GPS synchronized clock system offers accurate time to all clocks in the system. The GPS clock synchronization system consists of a master clock and multiple slave clocks. The master clock communicates with all the salve clocks via wired/wireless medium in the system to provide them with an accurate time source. The objective of the GPS synchronized clock system is to make sure that all clocks in the system display the same time. Regardless of which part of the building you are in, the time shown by the clocks will be uniform and accurate.
-
product
4-Channel High Speed Position Comparison and Trigger Module
ECAT-TRG4
The ECAT-TRG4 is EtherCAT slave module with high-speed position comparison trigger and encoder single redriver function, helping machine and equipment builders to use multiple triggers simultaneously for AOI, glue dispensing, display tests, and storage assembly applications.
-
product
PXI 5A Mux 1-Bank 48-Ch Isolated COM
40-651-011
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
PXI 16 x SPST Reed Relay
40-115-021
Available in normally open (DPST & SPST) configurations. Connections are made via a front panel micro-D 96-pin male connector. For applications requiring improved bandwidth and crosstalk performance please look at our 40-120 and 40-125 range of shielded reed relay cards. General purpose reed relays are suitable for the construction of small switching networks, slaving up to larger switches or operating external devices (e.g. lamps, solenoids etc.). To simplify inter-relay wiring, interconnection points are built onto the circuit board easing the construction of complicated wiring.
-
product
PXI General Purpose 2A Relay Module 26xSPDT
40-131-201
These are low cost, general purpose electromechanical relay cards capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
product
PXI 64 x SPDT Electromechanical Relays
40-148-201
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
product
Single 8x2 1-Pole 16 Amp PXI Power Matrix With Loop-Thru
40-552-012
The 40-552 range of 16 Amp PXI power matrix modules is available in four configurations with matrix sizes of 8x2 and 4x4 and the ability to expand the matrix size with the Y-Axis loop-thru connections: e.g. 8x4, 12x4, 16x4, etc. (with 4x4 matrices) or 16x2, 24x2, 32x2, etc. (with 8x2 matrices). This range is capable of switching up to 16 Amps and up to 300VDC/250VAC hot switching and 400VDC/250VAC cold switching. These PXI power matrix modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors, and solenoids.
-
product
PXI 5A Mux 8-Bank 5-Ch Isolated COM
40-651-014
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
Single 8-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-013
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexers. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
product
Dial Up Modem Test
ModemTest 1.3
Test your dial up modem and telephone line for errors and connection speed. A local loopback test is provided as well as a master / slave test. The master / slave test requires 2 modems and 2 telephone lines. ModemTest is compatible with most dial up modems. (9.6 - 56Kbits)
-
product
Dynamic Digital I/O (3U), 32 Channels Up To 200 MHz W/512MB On-Board Memory, W/LVDS
GX5283
The GX5280 Series are high performance, cost-effective 3U PXI dynamic digital I/O boards with 32 TTL input or output channels and 32 LVDS input or output channels. The GX5280 Series offers an industry leading 512 MB of on-board memory and supports test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
product
Single 4x4 1-Pole 16 Amp PXI Power Matrix
40-552-001
The 40-552 range of 16 Amp PXI power matrix modules is available in four configurations with matrix sizes of 8x2 and 4x4 and the ability to expand the matrix size with the Y-Axis loop-thru connections: e.g. 8x4, 12x4, 16x4, etc. (with 4x4 matrices) or 16x2, 24x2, 32x2, etc. (with 8x2 matrices). This range is capable of switching up to 16 Amps and up to 300VDC/250VAC hot switching and 400VDC/250VAC cold switching. These PXI power matrix modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors, and solenoids.
-
product
Master And Slave
Smart I/O
An I/O server is a software which controls and monitors one or more PLCs /RTU's using various communication protocols.Our I/O servers are built on highly optimized Windows 32bit platform. They are capable of handling very large scale SCADA systems with minimal impact on CPU usage, resulting in effective timing and usage of available hardware.Currently, we have Master and Slave solutions for DNP3 and Modbus (ASCII, RTU, TCP). Please select the appropriate tab above for more informaiton.If you are looking for a specific I/O Server, please contact us with your needs.
-
product
General Purpose I/O Modules
HY-TTC 30XH
The HY-TTC 30XH is a CANopen based, user-friendly and smart Input/Output module that can be utilized as flexible control system extension in mobile applications. HY-TTC 30XH is used in combination with, and controlled by a master electronic control unit, communicating with the slave module via the standardized CANopen® protocol. By mounting the master control unit centrally on the machine and the I/O modules close to the sensors or actuators, a distributed electronic architecture can be implemented in order to reduce mounting time and cost for cabling.
-
product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5280 Series
The GX5280 Series are high performance, cost-effective 3U PXI dynamic digital I/O boards with 32 TTL input or output channels and 32 LVDS input or output channels. The GX5280 Series offers an industry leading 512 MB of on-board memory and supports test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
product
C Series CANopen Interface Module
The C Series CANopen Interface Module is a high-speed interface for developing CANopen applications. CANopen is a higher-level communication protocol based on the controller area network (CAN) physical layer. It was designed for motion-oriented machine control networks, but now it is used in a variety of products and applications, including medical equipment, maritime electronics, building automation, and more. The C Series CANopen Interface Module can transmit and receive process data objects (PDOs) and service data objects (SDOs) according to CiA-DS 301. Using the NI-Industrial Communications for CANopen driver, you can batch edit SDOs, configure slave nodes with LSS services support, as well as perform network management (NMT), heartbeat, node guarding, and CANopen synchronization functions.
-
product
PXI 10 Channel Power Mux 1 Pole
40-660-001
Model 40-660 is a 10-Channel Power Multiplexer, suitable for switching inductive/capacitive loads up to 10A at 250VAC. It is available with a choice of 1-pole (10A) or 2-pole (8A versions). Model 40-665 is a higher density 18 Channel Power Multiplexer with the same specification as the 40-660. Power Multiplexer Modules are intended for switching heavy AC or DC loads or for slave switching large external relays, contactors and solenoids.
-
product
Temperature and Process Controllers
The ATR121 Temperature Controller is a 3 digit display PID controller with up to 2 relay outputs, Solid State Output and an option to be a Modbus RS485 Slave device.The ATR141 Temperature Controller is a 4 digit PID controller and Panel Meter which can display up to 3200°F with an S Type Thermocouple. The ATR141 can have up to 2 relays, a Solid State Output and an option to have a Modbus RS485 output.
-
product
Ethernet to Modbus RTU Interface
Model 9099
* Use Modbus TCP/IP, VXI-11, or Raw Sockets (Telnet) or to control Modbus RTU slave devices.* No special driver required which eliminates driver problems.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Interfaces with PLCs or any Modbus TCP/IP Controller.* Fully VXI-11 compliant.* Works with Agilent, NI and Kikisui VISA libraries.* Internal webserver with sample Modbus device control pages for Watlow F4, F4T and EZ-Zone Controllers.* Network connectivity eliminates GPIB Bus Extension problems.* Allows multiple users to access the Modbus network or devices.* 9099 is a 2x to 5x faster than the 8099 and includes a new Modbus device control page.
-
product
PXI Multiplexer, Very High Power DC, 4-Channel, 40A, 14V
40-664A-001
The multiplexer is suitable for switching heavy loads or for slave switching large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of DC voltage at high current.
-
product
PXI 50 x DPST Electromechanical Relays
40-146-202
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
product
PXI 20Amp 28Volt 4xSPST Automotive Relay
40-180-111
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC.The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
product
Exerciser with SMBus Support
Summit Z3-16
The Summit Z3-16 with SMBus Support is a critical test and verification tool intended to assist engineers in developing and improving the reliability of their systems. The Summit Z3-16 with SMBus Support can emulate PCI Express root complexes or device endpoints, allowing new designs to be tested against corner case issues. In addition, it can emulate SMBus traffic as a master or slave.
