-
product
Half, Full Bridge & Three Phase Drivers
Renesas' half-bridge (h-bridge), full-bridge and three-phase drivers handle voltages up to 100V, with industry-leading gate rise and fall times and exceptional input-to-output propagation delay performance.
-
product
AA06A Baratron® Absolute Pressure Sensor
AA06A Baratron® absolute pressure sensors are single-ended dual-electrode/AC bridge devices that are extremely stable and designed to minimize the effect of temperature changes. Full Scale ranges are available from 25,000 Torr down to 0.1 Torr. Each range measures down to 1 part in 106 Full Scale with selected percent Reading accuracy limited by this resolution and with accuracies ranging from 0.25% to 0.05% of Reading. They are constructed of Inconel® and stainless steel, allowing use with many wet, dirty, or corrosive gases.
-
product
PXI Strain Gauge Simulator Module 2-Channel, 350 Ohm
40-265-012
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 350Ω) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
PCIe X8 And X1 Bridge Card
The Guzik PCI Express Host Interface Bridge Card was designed to expand the x8 PCI Express Gen 2 (PCIe) slot in a host PC to an AXIe or a Guzik GSA 6000 chassis via a x8 PCI Express Gen 2 and a x1 PCI Express Gen 1 high speed PCI-SIG specified data cables. This allows the end node to connect to the host bus at speeds up to 3.2GByte/sec user data rate. The Bridge Card installs in a x8 or x16 slot of a PCIe backplane or a PCIe motherboard, provides additional board-based retention and reinforced front panel.
-
product
Power Transformers
Power Transformers are used to convert voltages and isolate signals for functionality and safety. Our broad line of catalog and custom solutions range from mW to 5-10kW and are used in multiple topologies including flyback, forward, push-pull, resonant, LLC and phase shifted full bridges. Typical operating frequencies are between 80-500kHz but solutions can be adapted for greater than 1MHz operation.
-
product
AC Resistance Bridge
SIM921
Stanford Research Systems, Inc.
The SIM921 AC Resistance Bridge is a precision, low-noise instrument designed for cryogenic thermometry applications. With excitation power below 100 aW, thermistors and other resistive samples can be measured at temperatures below 50 mK with negligible self-heating errors
-
product
Bridging And I/O Expansion Versatility. Rapid Hardware Acceleration For Improved Signal Control.
MachXO2
*Up to 256 kbits of user Flash memory and up to 240 kbits sysMEM™ embedded block RAM*Up to 334 hot-socketable IOs that avoid excess leakage*Programmable through JTAG, SPI, I2C or Wishbone*TransFR feature allows in-field design update without interrupting equipment operation*Programmable sysIO™ buffer supports LVCMOS, LVTTL, PCI, LVDS, BLVDS, MLVDS, RSDS, LVPECL, SSTL, HSTL and more
-
product
Arm-based Application Ready and Programmable IIoT Gateway
EMU-200 Series
The EMU-200 series is an Arm-based IIoT gateway that bridges OT and IT, enhancing data flow and cloud integration.The EMU-210 is a high-performance IoT gateway based on the i.MX 8M Plus, featuring an open platform design with a quad-core processor, making it suitable for edge computing and AIoT applications that demand higher performance.
-
product
PMC-to-PCI Express Adapter
4733
The Technobox, Inc. P/N 4733 PMC-to-PCI Express Adapter permits the use of a single-wide PMC module in a 4X PCIe slot. The product features a PEX8114 bridge running in transparent mode. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card. 64-bit support.
-
product
Thermal Conductivity Gas Analyzer
CI2000-RQD
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
Determining gas concentrations by measuring the thermal conductivity of the gas, CI2000-RQD analyzer uses advanced thermal conductivity sensor with single chip technology. It adopts platinum thread as sense organ to make up Imbalance Bridge, which output signal has a relationship with tested gas volume. And the single chip will magnify, sieve wavelength, modify linearly and criteria the signal by electric procedure.
-
product
Compact Design Measurement System
Benchmark 450
The Benchmark's fixed bridge design separates the X and Y axis motions, allowing each to operate without any influence on the other. This arrangement provides the maximum mechanical integrity and accuracy in the stage motion. The bridge type design also makes loading and unloading of large parts more efficient, and helps to minimize the overall footprint of the system.
-
product
IO-Link Transceivers
IO-Link is a Factory Automation fieldbus-independent communication standard dedicated to connecting sensors and actuators as described in the IEC 61131-9 standard. Easily integrated with any of the most commonly used communication protocols found in factory automation systems through dedicated interfaces or bridges, it is a simple solution for extending existing networks to connect remote sensors and actuators. Developers will take full advantage of the Industry 4.0 or Industrial Internet of Things (IIoT) concept where every sensor and associated data point is used to control and optimize even the most complex industrial processes in real time.
-
product
COMPUTERIZED AUTOMATIC RELAY TEST SYSTEM
CVRT-S16
CVRT-S8 & S16 are ideal for automatic testing of ELECTRO MECHANICAL AND READ RELAYS (only DC relays) both for static and dynamic characteristics. This system scans at one stroke, all the parameters of the relay as per definition of test procedure. The test sequence can be pre-programmed and stored in the disk. You can select the tests as per your requirement. Can include or exclude the test and you can have several options to match your test definitions. Semi skilled person can be engaged for actual testing, as he need not make any settings and need not interpret the readings. The system conducts the tests and gives PASS / FAIL indication on overall test results. If a printer is connected, each test result will be printed.Test Parameters : -> Coil Resistance.-> PickUp/Pull In /Operating Voltage or Current Linear Ramp Method or Step Method.-> Measure Pickup Contact Gap FBB-LBB V or mA-> DropAway/Drop Out/Release Voltage or Current Linear Ramp Method or Step Method.-> DropAway Contact Gap FFB-LFB V or mA-> % Release Dropaway/Pickup-> Contact Resistance of all contacts both Front and Back contacts.-> Operating Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while Operating @ above-> Release Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while release @ above-> Difference of Operate Time - Release Time.-> Bridging Test or Non Overlap Test.-> Transfer or Traverse Times while Operate and release.-> Operate Time @2nd Set Voltage or Current.-> Release Time @2nd Set Voltage or Current.-> Power Consumption @ Rated Voltage.-> Coil Current @ Rated Voltage at Room Temperature.-> Coil Resistance Corrected to 20deg C.-> Timing Waveform Graph for all active Contacts.
-
product
Double Regulation Power Supply
Double regulation power supplies include: DO series, AxN series, ATR series.The Power Supplies of the AxN series are built with the double regulation technique. The first regulation is obtained by the partialization of the grid circulation angle as automatic variac. The second regulation functions as a linear stabilizer with constant dissipated power. As a result, this solution allows to obtain both low power dissipation and, thanks to the linear regulation, excellent output characteristics.DO series Power Supplies are made with the double regulation technique. A linear stabilization circuit is added to a thyristor-controlled bridge, which allows to reduce the power absorbed by the network. This type of control allows a volume reduction compared to linear power supplies but it preserves the characteristics of low noise and speed of response.ATR linear Power Supplies series are built with the double regulation technique. the first regulation is obtained by the personalization of the grid circulation angle as automatic variac. The second regulation functions as a linear stabilizer with constant dissipated power. As a result, this solutions allows to obtain both low power dissipation and, thanks to the linear regulation, excellent output characteristics.
-
product
Interfaces And Control Boards
Acts as a bridge between a machine, motor controller, or PLC and related drive amplifier, feedback device and/or software.
-
product
PXI Strain Gauge Simulator Module 4-Channel, 3k
40-265-104
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 3kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
VME to USB 2.0/Optical Link Bridge
V3718
The V3718 is the new VME to USB 2.0/Optical Link Bridge that fully replaces the V1718 (VME-USB) and V2718 (VME- CONET) models. The Bridge Implements a VME master controlled by a PC via USB 2.0 and Optical Link (CAEN CONET protocol) including all the functions of its two predecessors in a unique device. The mechanics is 1-unit wide VME 6U.
-
product
Rugged Aircraft Interface Devices
AB2-AID
The AB2-AID is ready to go with high-performance avionics I/O combined with valuable built-in features such as a 9-port Ethernet switch, Ethernet to serial bridge, and 8GB flash memory. All in a compact, rugged package for easier integration and longer life.
-
product
Infotainment Platform & Boards
ADLINK offer ADi-SA1X/SA2X series, a true application-ready gaming platform, that is designed to meet the GLI-11 (Gaming Laboratories International) certification and major global gaming market compliance requirements. The comprehensive middleware as well as the security and extensive I/O solutions enable developers to easily bridge applications with peripheral devices, sensors, and surrounding solutions up to central monitoring and control systems that shorten customers TTM .
-
product
Prefabricated Torque & Thrust Sensor
Teledyne LeCroy Test Services patented Quick Sensor is a pre-fabricated Torque & Thrust Strain Bridge that is applied to a shaft much the same way as a strain gage. This time-saving device was developed for the Nuclear Power Industry to reduce the time and effort required to install strain gages in a radioactive environment. Since it's introduction in Nuclear Plants, the Quick Sensor has become popular in many other industries and applications where gaging time and cost is a concern.
-
product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-02
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
product
Local Bus Master & Target Bridges
PCI 9052
The PCI 9052 PCI I/O Accelerator provides low cost connectivity for PCI slave designs. It is specifically targeted at easing the transition of existing ISA designs to the more feature rich and performance oriented PCI bus.
-
product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781028-01
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
product
MirrorLink Test System
Catena 2210
The Catena 2210 is a test tool with two USB Network Control Model ("NCM") devices. These devices create a bridge between two USB hosts. Validation testing is made possible by connecting a test control computer to the USB host being tested. Ethernet traffic from the test host is transferred through the Catena 2210 device to the control host, and vice versa.
-
product
VME64 to USB 2.0/Optical Link Bridge
VX3718
The VX3718 is the new VME to USB 2.0/Optical Link Bridge that fully replaces the VX1718 (VME-USB) and V2718 (VME- CONET) models. The Bridge Implements a VME master controlled by a PC via USB 2.0 and Optical Link (CAEN CONET protocol) including all the functions of its two predecessors in a unique device.
-
product
65 lane, 17 port, PCI Express
PEX 9765
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe. Yet ExpressFabric works seamlessly with other standards used within the rack and in rack-to-rack connectivity.
-
product
2 Port T1/E1/PRI + 4 Port FXS PSTN
CH-4FXS-MOD-2PRI
One of the most feature rich PSTN simulator on the market. Unit has 4 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, V.90 modems, RAS servers, audio conference bridges or anything that requires analog phone lines. 2 port T1/E1/PRI module provides non-blocking switching among FXS ports and any of T1/E1/PRI B-channels or Time slots.
-
product
Capacitance/Loss Bridge
AH 2550A
The AH 2550A offers unparalleled stability, resolution and accuracy in a capacitance/loss bridge (whether manual or automatic). Its numerous state of the art features make it an exceptionally user-friendly instrument, just as was its predecessor, the AH2500A. The precision and ease of use of the AH2550A are creating new applications in science, calibration, and production in a wide range of fields.
-
product
Smart Aircraft Interface Devices
webCS
The Ballard webCS® is the first highly integrated smart AID/server/router that securely bridges avionics data with wired and wireless networks in a single compact box. This wireless aircraft communications server platform is simple to install and configure, safe to interface with aircraft domains, and provides highly secure data transfer. The compact, versatile webCS enables aircraft operators to easily gather and process aircraft data, and then route it to where it is needed—whether on or off the aircraft.
-
product
Maritime
Nieaf-Smitt maritime instruments are designed, engineered and manufactured for bridge, bridge-wing and control/rudder room applications on board of ships. Prime applications such as propulsion, steering and navigation are covered with a wide range of dedicated products.
