Current Amplifiers
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
High Voltage Amplifier
HA-805
-
*800Vp-p(±400V DC) *200mAp-p(±100mA DC) *Bandwidth: ≦300KHz(400Vp-p) *Slew Rate: 300V/us *Gain(AMPL):0~180(10 Turn VR) *DC Offset: ≦0~±400V(10 Turn VR+SW) *Output Resistor: 100Ω *Microprocess Control Protection
-
Product
Hall Effect DC Current Sensor
CYHCT-WS3
-
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-WS3 is a Hall Effect sensor for the measurement of DC current. The sensor has agalvanic isolation between the high power primary conductor and the secondary electronic circuit and withdifferent output signals and different power supplies.
-
Product
Resistors for Calibration of Current Measuring Systems and Sensors/Transducers
-
ChenYang Technologies GmbH & Co. KG
Is designed and made according to the Standard JB/T8225-1999 for DC resistors used in laboratory and electrical engineering.By using full closed structure and automatictemperature control it ensures resistor good long-term stability and small temperaturecoefficient. This DC resistor is very suitablefor DC current measurement and calibration of current measuring systems and current sensors. The maximal measuring current is 100A with measuring accuracy of ±0.02%
-
Product
Leakage Current Tester
2675
-
Shenzhen Chuangxin Instruments Co., Ltd.
RK2675 series Leakage Current Tester is used to measure the electrical insulation quality and products’ safety performance of the main indicators.
-
Product
Panel-mounted HIL Power Amplifier
PAC60Ci
-
PAC60Ci is the six-phase real time simulation amplifier, with maximum RMS phase current of 30A and maximum output power of 450VA. This current amplifier is possessed of high accuracy and fast liner response.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Amplifier Modules Broadband
-
Modules are usually smaller and are usually part of systems. You supply your own DC voltage, make the connections and supply your own DC supply. Modules are available with or without heatsinks and fans. Amplifiers Modules are available in both Broadband and Band-Specific frequencies. Modular design concepts save time and money, and are lightweight, reliable, cost-effective solutions. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
-
Product
High Power Precision Current Sensing Resistors
HPCR4T
-
High Power Precision Current Sensing Resistors of HPCR4T designed with four terminals, are distinguished by excellent long term stability & TCR. The Kelvin connections of this device allow for high precision measurements even with low resistance values. HPCR 4T has a non-inductive copper manganin element inserted into the ceramic case and finally sealed with a cement molding.
-
Product
Zero Phase Current Transformer
MZL-45
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Split-core type for measuring zero phase current
-
Product
Multiparameter Current Meters
MIDAS ECM
-
The MIDAS ECM is one of only a few multiparameter current meters that allow real-time operations over several thousand metres of cable, as well as autonomous deployment.
-
Product
High Voltage Amplifier
HA-405
-
* 400Vp-p(±200V DC)* 400mAp-p(±200mA DC)* Bandwidth: ≦1MHz(200Vp-p) *Slew Rate: 500V/us *Gain(AMPL):0~90(10 Turn VR) *DC Offset: ≦0~±200V(10 Turn VR+SW) *Output Resistor: 50Ω *Microprocess Control Protection
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-18
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Ultra compact size with 18mmφ jaw opening capability.*High sensitivity and least affection from external magnetic field.
-
Product
High End Current Sensors
-
AC and DC currents with an accuracy down to 1ppm. Our standard products offers the following features: Automotive current sensors. Extended temperature current sensor - 85 deg Celcius. AC current sensor - DC current sensor.
-
Product
EMI Amplifiers
-
Overvoltage protection,shuts off above 29VOver-temperature protection,shut off above +100°CExcellent IP3 Class A amplifierVSWR Short and Open circuit protection
-
Product
Current Probe
PA-629
-
*Maximum Current Value: +/- 200ADC, 140A RMS*1mA = 10mA, 100mA (switchable)*Rising Time: 1.2uS*Bandwidth: DC ~ 300kHz*Over Range Indicator*Battery, AC Power Supply Adaptor (free), dual usages
-
Product
Erbium Doped Fiber Amplifier
S-102
-
The EDFA slot module of FOTS system with built-in power booster EDFA module offers a special function that is able to change the optical signal amplification feature variously, which is followed by user’s driving embedded pump LD freely. The output power of eash pump LD can be controlled separately by the program that is set up by user. When an optimum optical signal amplification particularity is needed, it is made up so that it can be materialized by choosing the Default mode provided along with User mode. More stable application of EDFA is possible through the monitoring of the factors such as in/out signal power, gain, alarm status and pump LD enabled by the application of FPGA processor which makes high speed driving possible. It is also set up that user’s present-time monitoring and control through LCD monitor of system main frame or GUI display for remote control can be possible. Through optimization of amplifier gain, noise figure, and saturated output power, this EDFA module will expand test capabilities in systems, components or sub-assembly manufacturing.
-
Product
Mini AC Leakage Current Clamp Tester
M-104+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・33mmφCT window and ultra compact size.・Data-hold function. Especially useful when working in dark or hard to get areas.・Low cost type, Core shielding is not equipped.
-
Product
High Current Test System
-
HIGHVOLT Prüftechnik Dresden GmbH
High current test systems are used to test the thermal stability of equipment and components. The test system induces a current in the test object causing it to heat up. Therefore, the test object is designed as a shorted circuit. The high current test system measures the temperature of the test object at various points, in addition to the current. As a special feature, the temperature that the test object should reach can be specified and the amount of the current can be automatically calculated by the HIGHVOLT test system.
-
Product
Composite 2×12 Video Distribution Amplifier
VDA212RM
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Wideband Distributed Amplifiers
-
Analog Devices GaAs MMIC-based wideband distributed amplifiers cover the dc to 65 GHz frequency range in various ultrawide bandwidths. Our design catalog includes low noise amplifiers, power amplifiers, and driver amplifier designs to meet your needs in applications such as electronic warfare, radar, electronic countermeasures, optical applications, and instrumentation. To meet diverse design requirements, some of our LNAs also offer internal-self biasing that requires only a signal drain voltage to operate.
-
Product
Inrush Current Generators for Zno Production Line
-
Shanghai Guantu Technology Co., Ltd.
Inrush Current Generator Standard: IEC61008, IEC61009, I61051/61643, ANSI C62.31, C62.33, C62.35, TU K20, K21, K44, K45, UL943Inrush Current Generator Features1. LCD screen display, built-in computer control, man-machine dialogue, easy to operate.2. Program-controlled high-voltage power supply, high voltage stability and precision3. Imported non-inductive high-power resistors are used to ensure the consistency of surge waveforms4. The main switch adopts electronic switch discharge mode, and the output polarity is automatically switched
-
Product
Current Transformers
-
A range of ring type current transformers suitable for primary currents from 1A-5000A with 1A or 5A secondaries. This standard range of measuring and protective current transformers is available as resin coated or tape wrapped.
-
Product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800B (2RU)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800B (2RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
Product
Handset Power Amplifiers
-
Broadcom Handset Power Amplifiers support different operating modes (CDMA, UMTS, LTE, and GSM/EDGE) and multiple frequency bands offering premium performance in a very small form factor.
-
Product
Split type AC Current Sensor
CTF-13NF
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Ultra compact size and high accuracy. * Easy installation in the distributing box. * Compliant with RoHS drective.
-
Product
C-Band Separate Dispersion Compensation Raman Fiber Amplifier
DRA5228/F
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Raman Fiber Amplifier (RFA) utilizes the optic gain in the Stimulated Raman Scattering (SRS) in the optical fiber and realizes the amplification of the signal optic. FRA, with very low equivalent noise and a wide gain scope, can further widen the gain bandwidth by adopting multi-wavelength optical bump, which represents the development direction of the new optical fiber amplifier.
-
Product
Split type Pulse Current Sensor
PCT-06
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Through hole type pulse current sensor.*Pulse current sensor for power demand meter.
-
Product
Fluxgate 150A Current Sensor
LF03
-
Our LF03 current sensor works with the dynamic Fluxgate measurement technology. It is characterized by its simple, practical design and prevents high temperature drifts. Fluxgate technology uses the phenomenon of magnetic saturation to modulate the measured magnetic field and convert it into an electric field.
-
Product
Amplifiers
-
We have designed and manufactured amplifiers using all major semiconductor materials, LDMOS, GaN, GaAs, and InP, to produce narrow, wideband, and pulse, receive and transmit amplifiers from 1 MHz to 220 GHz and power levels from mW to over 10 kW.
