Drives
-
Product
IPM Drive
-
IPM drive photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode and signal processing circuit on the output side in a single chip. This coupler is a high common mode transient immunity (CMR), high CTR type whose pulse width changes according to the operating temperature, making it ideal for driving IPMs (intelligent power modules).
-
Product
High Impedance Active Probes
7
-
Designed as a companion probe to Models 12C and 18C for driving integrated circuit lines so the Model 12C and 18C can be used to measure the response of adjacent nodes. The Model 7 consists of a flexible 6 foot, 50 ohm coaxial cable accurately terminated to 50 ohms in order to avoid undesirable reflections. A special miniature connector receives replacement coaxial probe tips that provide a shielded environment to within 3 mm of the fine tungsten probe point, thus minimizing capacitive coupling to other parts of the circuit. The replaceable coaxial probe tips are offered in various point sizes and can also be bent to any shape in order to accommodate a variety of probing geometries.
-
Product
Semiconductor
-
The semiconductor industry faces continuous pressure to reduce device size and costs while improving performance and reliability. Semiconductor, test and assembly automation manufacturers demand the same improvements from the motion technology which drives it. Haydon Kerk Pittman continues to develop new technologies in motors, lead-screws, gears, encoders, actuators, slides, drives and complete sub-systems that increase operational speeds and accuracy while lowering the cost of ownership.
-
Product
High Frequency Surge Testers
-
The 50KV Digital P J High Frequency Surge Tester is the most powerful tester in a class of its own. No other 50KV Surge Tester can pulse/resonate 60 pulses per second at a risetime of 100 nano seconds.This powerhouse is loaded with the TDS3012B Digital Phosphor colored oscilloscope with a built-in floppy disk drive.
-
Product
Syringe Pump
500x
-
The 500x syringe pump provides precise, predictable flow and pressure control at flow rates from sub-microliter up to 204 mL/min. Exceptional low-flow stability at up to 5,000 psi (345 bar) makes this the ideal pump for high pressure applications from deep well core analysis to a wide range of chemical applications.analysis to a wide range of chemical applications.The SyriXus controller has backlighted keypad and 4-line LCD display, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly. Control the pump remotely using driver for LabVIEW™ software, in addition to pump controller. The 500x pump module has a single-ratio drive train with auto-lubricating gears for long life and low maintenance. Special fittings are used to prevent leaks and ensure safety at maximum pressure. Wetted materials are compatible with most aqueous and organic liquids, corrosive solutions, heated fluids, liquefied gases, viscous fluids, or slurries and pastes. Hastelloy cylinders are available for chemical compatibility of corrosive solutions. Single and continuous valve packages are 100% Hastelloy for full compatibility. Trust in the Teledyne LABS SyriXus pumps for proven reliable design. Known for years of performance, it can delivery fluid or pressurized gas for long term experiments. Or hold pressure constant in the system at a simple click of the button.
-
Product
Non Contact Flange Torque Transducer
FF425
-
Contactless Torque Transducers with flange couplings at either end with measuring ranges from 0-100Nm up to 30kNm as standard (bespoke sensors up to 16MNm) for a variety of in line static and rotary torque measurement applications.The Datum Electronics Series FF425 non contact flange torque sensor and FF410 torque sensors have been designed to fit easily inline with any drive train or test rig using standard DIN size couplings. With Flange couplings at either end of the torque transducer, it has many advantages over other torque measurement systems on the market.
-
-
Product
Autonomous Driving Solutions
-
ADLINK envisions a world where people, places, and things are positively enabled with AI-driven capabilities. Vehicles will be integrated with software, sensors, communications, and reliable computing hardware, making society safer, travel more enjoyable, and enabling leaps in productivity.
-
Product
EtherCAT Chassis with EtherCAT Bus-Coupler
EPS-9905 with EPS-6000
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
4-CH RTD Thermal Input EtherCAT Module
EPS-3504
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
Hard Disc Drive Connectors
-
Teledyne Impulse provides a broad array of disc drive connectors. Our connectors are RoHS compliant and are being used on most major platforms around the world. Teledyne offers its cone point technology to insure maximum connectivity performance, and high temperature plastic materials are common. Teledyne's products are designed to meet the global requirements of the computing industry. Custom design configurations are available upon request.
-
Product
EMP- EMI Solutions
-
We have spread our business tentacles and are operating smoothly, through our DELHI NCR branches which are having facilities like Mechanical and Electronic Designs, Manufacturing, Integration and Testing for development and production activities. We have the In-house Environmental and EMI pre-compliance test facilities which guarantee better quality products.It is our pledge to serve the society with more efficient and qualitative output through our open mindedness and creative solutions. We continue with ardent hope that our products will definitely gather more and more momentum with the defence, the private industrial bigwigs and international companies as well. Growing the business tentacles in India, Concept Shapers are embarking upon the drive of expansion of the resources at its disposal. Our resources are our strength, be it human or the space. We firmly believe in the doctrine of ‘Engineering Innovative Concepts to configure a better tomorrow’.
-
Product
POWER ATTENUATORS
TYPE ATF
-
National RF’s Type ATF Power Attenuators were designed to allow interfacing of linear power amplifiers to RF exciters, where a specific amount of drive to the amplifier is prescribed. Often, however, drive from the RF exciter exceeds this minimum prescribed level and some form of power attenuation must be used in order to not damage the input of the power amplifier. National RF’s type ATF-3 offers 3 dB of power attenuation (1/2 of the power) when used between the exciter and the amplifier and will handle an input power of 132 Watts, RMS (continuous power) while providing about 66 Watts RMS output power, when it is terminated into 50 ohms. In practice, the ATF-3 attenuator will handle exciters achieving Peak Envelope Power levels (PEP) in the area of 200 to 250 Watts while providing half of that power to the load. For less attenuation requirements, the ATF-1 and ATF-2 offer 1 and 2 dB of attenuation, respectively.
-
Product
PMC Analog Out Board
MS 1821
-
*Bus Interface:- 32 Bit PCI Bus with PMC Interface*Speed of operation up to 66MHz*Spartan-3AN FPGA based design*32 channel single ended analog Output*Unipolar or bipolar voltage output*Programmable output voltage: 0-5V, 0-10V, 0-10.8V, ±5V, ±10V, ±10.8V and is capable of driving up to +/-20mA*16 bit Resolution*Conversion time 10usec typ*Over current protection*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
Product
Tri-Mode I/O Controller
SAS3808
-
Broadcom Tri-Mode SerDes technology enables seamless operation of PCIe, SAS or SATA storage devices in a single drive bay. The introduction of PCIe devices executing NVMe to the existing SAS/SATA infrastructure makes industry standard, hot-pluggable drive bays even more versatile. Whether you’re building external or cloud-based storage systems for high connectivity, or outfitting servers, the SAS3808, 8-port, 12Gb/s Tri-Mode SAS/SATA/PCIe Gen 4.0 IOC provides choices for storage optimization by enhancing direct-attached storage (DAS) solutions.
-
Product
Accelerated Stress Test Chamber
-
CSZ's accelerated stress test chambers combine mechanical refrigeration; LN2 cooling and high velocity air flow for fast product temperature change rates. Chambers are typically designed with a change rate up to 30C (54F) per minute based upon the part temperature. Common uses are production stress testing circuit boards, electronic drives, assemblies, etc. Design allows the user to quickly control and change the temperature of the product.
-
Product
Environment Monitoring System
ENVIROMUX-2D
-
The ENVIROMUX-2D supports 2 external configurable sensors, 5 digital inputs, and 1 output relay for control of external devices. It features 2 USB ports for USB modem, USB flash drive, or USB LCD screen. Linux inside.
-
Product
6U OpenVPX Quad Drive Storage Module
563x
-
The 5632 & 5633 support multi-terabyte storage in one 6U slot with capacities current solid state drive technologies. Four on-board SATA drives connect via the backplane via SATA controller to create a high capacity multi-slot storage array.
-
Product
MASK MVM-SEM® E3600 Series
E3640
-
Ongoing semiconductor process shrinks are driving new demand for stable, highly precise measurement of pattern dimensions for photomask and wafer production. The E3640 satisfies these requirements with industry-leading precision measurement capabilities and upgraded functionality that enhances mask R&D and production efficiency.
-
Product
Double Voltage Double Frequency Generator Setup
DVDF
-
This test setup is generally used to perform induced voltage test on the transformers. This set up consists of the USED motor and generator combination to develop the required voltage and frequency. Both generating unit and the drive motor are mounted on a common metallic frame.
-
Product
34945A Distribution Board, With Generic Screw Terminals For Driving 16 Switch Coils
Y1155A
Distribution Board
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
Product
LV Iron Core Harmonic Filters
-
Nonlinear loads such as power electronics based equipment and electric furnaces are sources of harmonic currents leading to harmonic distortion, which is one of the most important parameters for defining the power quality. Most of the commercial loads such as personal computers, photocopy machines, power supplies, and compact fluorescent lamps; and industrial loads such as AC and DC motor drives inject harmonic currents into the network that they are connected to.
-
Product
Single Beam Interferometer
10705A
-
The Keysight 10705A Single Beam Interferometer, the smallest linear interferometer, is designed for making low mass or limited space single axis measurements. It is ideal for use in disk drive and other confined space applications. The single beam interferometer is called that because the outgoing and returning beams are superimposed on each other, giving the appearance of only one beam traveling between the interferometer and the retroreflector.
-
Product
Disk Drive
PMC-0247RC
-
The PMC-0247RC is a RoHS Serial ATA hard disk drive in the PMC form factor, designed for use with our single board computers (SBCs) or PMC expansion cards with an available PMC site. Because it supports universal signaling it can be installed in any available 3.3V or 5.0V PMC site. The PMC-0247RC uses a 2.5-inch hard disk drive and has a maximum capacity of up to 250 Gbytes. Also, 16GB, 32GB and 64GB solid state drives are available.
-
Product
2U Rackmount Chassis For ATX/Micro ATX/Mini-ITX Motherboard
AX61223TM
-
*Supports ATX/Micro ATX/Mini-ITX motherboard*Supports ATX power supply*Internal one 3.5" HDD drive bays*Front-accessible one 3.5", one 5.25" HDD drive bays and one slim CD-ROM bay
-
Product
Internet of Things
-
The Internet of Things (IoT) is connecting billions of intelligent “things” to our fingertips. The ability to sense countless amounts of information that communicates to the cloud is driving innovation into IoT applications such as smart home, industrial IoT, the connected vehicle, smart cities, wearable infotainment and wearable fitness/heath.
-
Product
Wall Mount Power Supplies
AC-DC Triple Isolated Outputs
-
Triple isolated output power supplies provide the features and characteristics of three supplies in one compact, easy-to-use package. They are available in the voltage combinations most frequently required for driving microprocessors and associated circuitry.
-
Product
Memory Test System
T5851/T5851ES
-
The T5851 system is designed to provide a cost-effective test solution for evaluating high-speed protocol NAND flash memories including UFS3.0 universal flash storage and PCIe Gen 4 NVMe solid-state drives (SSD), both of which are expected to be in high demand for the LTE 5G communications market.
-
Product
Torsion Testing Machine
-
Unique ‘TALCON-CLAW’ Grips for Round and Flat SpecimensTorsional Speed of 0.1/0.2 RPMTorque Compensated MotorsMaintenance Free Gear Box Auto Range Selection with Range Selector Wheel (Optional)3 or 4 Torque Ranges for Higher Accuracy (Optional)Load-unload Capability Variable Speed Drive (Optional)
-
Product
1U Rackmount Network Appliance Platform With Intel® Xeon® Processor D-1527/ Pentium® Processor D1508 And 10 LANs
NA720
-
The NA720 is built on the server-class Intel® Xeon® D-1527 processor (codename: Broadwell-DE) and Pentium® processor D1508. The NA720 comes with two 10GbE SFP+ ports, eight Gigabit Ethernet ports and two expandable LAN modules supporting 1GbE/10GbE/Fiber/Copper/Bypass with a maximum of 26 LAN ports. Four DDR4-2400 MHz R-DIMM/U-DIMM sockets can provide system memory of up to 128GB and support both ECC and non-ECC memory types. For storage, it supports one mSATA and two 2.5” SATA hard disk drives. This high performance Intel® Broadwell-DE network appliance is an ideal solution for enterprise firewall, network bandwidth controller and UTM applications.
