Converters
Change a form or value and shows or transforms it into a different scale or value.
-
Product
DIO-AIO Conversion Set For Conventional Power Amplifier
PAD64
-
PAD64 DIO(digital input/output)-AIO(analog input/output) Converter is the equipment which could be used for DI/DO (Digital input/Digital output) conversion and galvanic isolation between Real-time simulation system and protection equipment, and any other equipment which need AIO (analog binary input/ output, dry contacts).
-
Product
RF Mixers & Frequency Converters Overview
-
Up and down conversion is often used because waveform generation in a transmitter is less expensive at lower frequencies and the dynamic range of analogue-to-digital converters in the receiver is higher at lower frequency.
-
Product
16-Channel VME Current Source & Analog Measurement Module
V460
-
The V460 is a VME-based versatile source/measurement unit. It includes a programmable constant-current source, a precision programmable gain 16-bit analog-to-digital converter, and a 4-wire, 16-channel analog multiplexer. An internal microprocessor supervises channel scanning according to user loaded parameters, reporting sensor voltage drops or, for selected sensor types, engineering-unit data.
-
Product
DALI 0-10v Converter
-
The DALI 0-10V Converter converts DALI signal to the Analog 0-10V protocol.
-
Product
Electrical Probe Systems
-
INSTEC's Probe Systems offer an integrated solution for performing component-level electrical measurements over a wide temperature range.Compact Mini Probe Stages enable an existing inspection microscope or optical test setup to be converted easily into a precision temperature-controlled semiconductor testing and qualification station.Analytical probe stations are fully featured industry-standard platforms for all modern probing applications and testing.Benchtop Probe Stations provide the user with four independent electrical probes with X,Y,Z micropositioning for precise placement without opening the sample chamber.Highly configurable probe systems meet a range of requirements for atmospheric and temperature control, sample areas, and electrical measurements.
-
Product
4-CH 16-Bit 80 MS/s PCI Express Digitizer
PCIe-9834
Digitizer
ADLINK's new PCIe-9834 high-speed PCI Express digitizer, featuring four simultaneously sampled 80 MS/s input channels with 16-bit resolution, 40 MHz bandwidth, and up to 1 GB DDR3 onboard memory. Each of the four input channels supports up to 80MS/s sampling, with 16-bit resolution A/D converter. This allows simultaneous recording of signals on all channels with no interchannel phase delay. The extremely large onboard memory enables long recording times even at the highest sampling rates. Each connection pair (lane) can achieve burst connection speeds of 250MB/s. The PCIe-9834, based on x4 lane slot PCI Express technology, provides a clear advantage in that direct connection of each slot allows full transfer bandwidth for each individual card.
-
Product
Loop-Powered Transmitters and Drivers
4-20mA
-
Loop-Powered Transmitters convert the output from proximity probes, seismic sensors, into a 4-20mA DC current, which is proportional to the input being measured. The transmitter converts the displacement or vibration signal to DC voltage and/or current for a DCS or PLC system. They control a 4-20mA current loop for a specified vibration range (ex. 0-5 mils peak-to-peak). The transmitters have a two-wire hook-up, powered solely by the loop current and have a power supply range of 15 to 36 volts.
-
Product
PMC Carrier with 4 positions
PMC-MC-X4
-
The PMC-MC-X4 adapter / carrier converter card provides the ability to install up to 4 (four) PMC cards into a small enclosure. The PMC-MC-X4 has two PMC card slots mounted front and rear to create a compact arrangement with 4 PMC slots. Suitable for 32/64 with 33/ 66 MHz bus operation.
-
Product
Bluetooth Enabled Signal Conditioners I/O Modules
microBlox
-
Acromag's microBlox uB Series I/O modules offer a compact, high-performance solution for interfacing sensors and field devices with data acquisition systems. uB signal conditioning modules are ideal to isolate, filter, convert and amplify a wide variety of signal types for test, measurement and control systems. Just plug uB modules into 4, 8, or 16-channel backpanels in any mix for a high-density analog I/O interface. Channel-to-channel isolation provides optimal noise and surge protection from ground loops, spikes, and high common mode voltages.
-
Product
DC DC Converter Models
-
These versatile DC-DC Converters are ideally suited for powering a wide variety of analog and digital circuitry, such as op amps, logic and microprocessors. They may be mounted directly on a printed circuit board for OEM applications, or installed in a socket for developmental and small quantity requirements.
-
Product
AC Power Sources, Frequency Converter
MAC-01, -02, -03
-
For reliability, all models of the Titan AC Power Sources/Frequency Converters are fully current limit protected against either continuous or transient short circuit or overload conditions. When an overcurrent condition exists, the internal current control loop overrides the voltage control loop and scales back the sinewave drive until it sees a safe output current level.
-
Product
Qualification and Quality Control Tests
Techsquare
-
New IEC standards, IEC 60034-18-41 and IEC 60034-18-42, have been issued to define the procedures for testing partial discharge inception voltage and the long-term performance (endurance) of Type I and Type II insulation systems used in rotating machines fed from voltage converters. Voltage impulse generators are required at least to test turn insulation, but they would be recommended for any testing under power electronics supply because of their capability to simulate the real electrical stress conditions. More generally, any type of electrical insulation system when subject to impulsive voltage waveform during life should be carefully evaluated in terms of partial discharge and endurance behaviour. This is why voltage impulse generators able to provide impulses with controlled amplitude and frequency are needed to face this new testing challenge.
-
Product
PXIe-7865, Kintex-7 160T FPGA, 24-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
787355-01
Multifunction Reconfigurable I/O
PXIe, Kintex-7 160T FPGA, 24-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module - The PXIe-7865 features flexibility of timing and synchronization with a user-programmable FPGA for onboard processing and direct control over I/O signals. The PXIe-7865 provides 24 analog output, 2 analog input, and 32, 5V input-tolerant digital I/O channels connected to a Kintex-7 160T FPGA to help you design applications for hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. You can use the dedicated A/D converter (ADC) for independent timing, individual channel triggering, and multirate sampling. Additionally, the PXIe-7865 includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
Product
Advanced Powder Resistance Kit
PRK-130
-
The PRK-130 is an advanced kit that includes the PRF-930 Powder Resistance Fixture for measuring the bulk resistance of powder and granulated materials. Test material is placed in the cavity between the measurement plates. Once a measurement has been made in ohms, a fixture calculation, or correction factor, converts the resistance measurement to volume resistivity in ohm-cm.
-
Product
LVDS To DVI-D Converter Board
AX93221
-
*Input supports 18/36/24/48-bit LVDS through 40-pin LVDS connector*Output supports DVI-D connector*Size: 60 x 50 mm*Applied for PICO821 and PICO822
-
Product
Power Quality Software
-
Save Time and Improve Accuracy When Troubleshooting AnswerModules® are proprietary algorithms that convert raw power quality event data into precise answers to determine the source and cause of the disturbance. Read More
-
Product
Power Supply Units
-
converts mains AC to low-voltage regulated DC power for the internal components of a computer. Modern personal computers universally use switched-mode power supplies.
-
Product
Industrial Automation
-
PLANET Industrial Automation solution is designed to help set up IP networking in the areas of Industrial 4.0 and IoT using the serial port connection. Our Industrial Automation product line includes RS232/RS422/RS485 Serial Device Servers, Modbus Gateways, EtherCAT Slave I/O Modules and Serial over Cellular Gateways, each of which enables to convert and transform useful data for further analysis to optimize factory operation and management.
-
Product
Vibration Signal Converter
-
High performance and low costSmall size, attachable with DIN railSwitchover Measurement Mode, switchover Measurement Range●Acceleration / Velocity / H Function / H Function CF *（only for VM-80DA)●Velocity / Displacement (VM-90 DV / DVL)Substantial basic functionsOne step alarm outputDC4 ～ 20mA level outputAC±5V monitor outputLevel indication
-
Product
Open Circuit Locator
A994
-
The A994 is an open circuit locator for electric and telephone cables wind on the reel; it gives the position of the fault from the inside or outside end of the cable, in percentage to the total cable length. The instrument measures the ratio of the capacitances of the two sections of failed conductor using two high precision i/v converters. The advantage of this method is due to the fact that the measurement error depends almost exclusively on the dimensional inhomogeneity of the cable. The A994 has the unique feature to permit the location of fault in cables with all broken wires. This instrument locates breaks in cables with a total capacity between 2 nF and 5 uF. The distance to fault is displayed on a large LCD display.
-
Product
IRIG B to NTP/SNTP Converter
-
Signals & Systems India Private Limited
IRIG B TO NTP/SNTP CONVERTER – SPC-INS-1010 is a compact DIN rail mountable protocol converter unit which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using IRIG-B signal obtained from GPS receiver. It provides nanosecond accuracy when external time references are not available. It has the storage facility to store the system log file. It delivers NTP, SNTP, PFC-Pulse, RS232 & RS485 outputs. The system enables configuration and monitoring through Web-based application. It supports a wide range of power supply input either 90V-260V AC/DC or 18-36VDC or 36V-72VDC.
-
Product
1GS/s 75MHz BW USB Modular Scope Pen
USBscope50
-
USBscope50 marks a new era in ultra portable modular instrumentation for the PC or notebook. Using a USB1.1 or USB2.0 port on the host computer, USBscope50 offers the best of all worlds for converting your PC into a powerful diagnostic tool: tiny size, low power, low cost, modularity and high performance.
-
Product
Audio A/D Converters
-
Analog Devices offers audio analog-to-digital converters (ADCs) for applications such as automotive, home theater, consumer audio, and PCs. These ADCs offer cost effective solutions and easy interfacing to ADI's SHARC® processor, Blackfin® processor, and SigmaDSP™ products.
-
Product
4-Channel 200 MHz, 16-bit A/D with Virtex-6 FPGA - PCIe
Model 78660
-
Model 78660 is a member of the Cobalt® family of high performance PCIe boards based on the Xilinx Virtex-6 FPGA. A multichannel, high-speed data converter, it issuitable for connection to HF or IF ports of a communications or radar system. Its built-in data capture features offer an ideal turnkey solution.
-
Product
Compressed Air Temperature and Humidity Regulator
H3021P-2
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Windows Client/Server Software For BACnet Systems
BACDOC
-
BACDOC is implemented as a Win32 DLL. The DLL works with BACnet/IP over Ethernet, and you can even use MS/TP through USB or any standard serial COM port, with an external EIA-485 converter. For legacy applications, you can use Ethernet 8802-3 with NDIS-compliant drivers, or PTP through any standard serial COM port.
-
Product
Serial Converter
USB-COMi
-
The USB-COMi is a USB to RS485 serial converter. It allows easy serial port expansion without requiring IRQ, DMA, or I/O port resources. The converter allows the user to easily and economically connect RS485 devices to a host using USB. The RS485 communications standard is used by DGH sensor based data acquisition modules and many industrial control devices.
-
Product
PCIe 16 Bit High Speed Digitizer - 180 MS/s on 2 Channels
M4I.4470-X8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Crowbar Resistors
-
Crowbar resistors are three phase resistance banks which are connected to the rotor windings of the DFIG (Doubly-Feed Induction Generator) such as wind power generator. They are used to prevent damage to the inverter circuits attached to rotor side when a fault occurs in the grid. DFIG power converter, which has a restricted over-current limit, needs special attention during faults in the grid. If the rotor current or DC link voltage reaches the threshold value, crowbar resistors disconnect the converter in order to prevent the generator turning into a squirrel cage induction machine. By crowbar resistors, the DFIG could stay connected to the grid and continue its operation.
-
Product
mAEStro Audio Digital to Analog Converter
-
The mAEStro ADAC-100 receives AES/EBU (AES3) or S/PDIF digital audio and converts it to two channels of analog audio. It automatically detects sample rates up to 96kHz with low-jitter clock recovery. Two balanced line-level audio outputs are provided on XLR connectors on the rear panel. For convenient monitoring, a stereo headphone mini-jack and volume control are provided on the front panel.
