OBD II
-
Product
Series II Standard Mass Flow Controller
-
Our Series II mass flow controllers & meters offer outstanding value in a wide range of applications. Exceptional accuracy for flow ranges from 0.014 sccm to 1,670 slpm, all with optional multi-gas and multi-range capability for maximum flexibility
-
Product
GMSL II Output FMC Module with MAX96705
TEF0010-01
-
Sundance Multiprocessor Technology Ltd.
FMC module with Xilinx Artix-7 FPGA and 4 x 16-Bit GMSL serializers.
-
Product
Motion Control Terminal Board for Yaskawa Sigma II Servo Amplifiers
DIN-814PA
-
This well-designed motion control terminal board is for the users who use Panasonic MINAS A super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
Product
CAN + OBD Network Data Converter
NC1
-
Get RPM, Speed, Absolute throttle position and many other vehicle parameters in real-time from your vehicle's standard OBD connector. Works with ANY OBD2 equipped vehicle. Works with ANY data acquisition equipment.
-
Product
Blanking Signal Generator II
MS 1609
-
This System used for generating continuous and pulsed variable power outputs (Voltage).
-
Product
InfiniiMax II Series Probe Amplifier, 12 GHz
1169B
-
Provides a large common mode range and a large offset range for measuring differential and single-ended signals.
-
Product
Relay Test Jumper Kit II
60610
-
Set includes four jumpers to fit many popular relays on Honda, Nissan, Toyota, newer Ford and GM mini micro relays as well as International trucks. Set comes in blow-molded case for storage. Simply remove relay to be tested, insert correct jumper and insert relay into jumper. When using grey four pin jumper be careful to align pins on jumper and relay correctly. No need to pierce wires or connect multiple jumper wires. Jumpers have tabs for clamping and flat pads to place test leads on.
-
Product
VHF & UHF Couplers for the PowerMaster and PowerMaster II
-
VHF-1.5K (2m), VHF-1.5K-2 (1.35m), UHF1.5K (440-450 MHz), UHF-1.5K-2 (420-440 MHz)
-
Product
CEMS II E Continuous Emission Monitoring System
-
CEMS II e takes away the manual configuration and settings adjustments from your day-to-day emissions measurements. A fully automated continuous emission monitoring system CEMS II e is TÜV and MCERTS certified solution (QAL1) to offer environmental compliance. This emission monitoring system is suitable for measuring pollutants continuously from hot, wet and corrosive gas streams in various industrial processes, such as powerplants, waste incineration, cement plants and beyond.
-
Product
CB-37F-HVD, 37-pin ScrewTerminal Blk, UL rec.150V CAT II, Din Rail
779491-01
-
37-Pin Female D-SUB to 37-Pin Female Screw Terminal, High Voltage Horizontal DIN Rail Terminal Block - The CB-37F-HVD features screw terminal connectivity for up to 37 I/O signals, 12 to 30 AWG. It has a female 37-pin D-SUB connector for connectivity to C Series I/O Modules and … data acquisition devices. The CB-37F-VHD is UL recognized. You can use the CB-37F-VHD with low-voltage or high-voltage products up to 150 V.
-
Product
SKYbolt II 6U VME 4-Slot
-
Delivering performance of 16 GFLOPS the SKYbolt II 6U VME solution adds intelligent support for system services and high-performance data transfers as the carrier board for the Merlin daughtercard which contains the compute processors, I/O interfaces, and global memory.
-
Product
NEX CG II Energy Dispersive X-ray Fluorescence Spectrometer
NEX CG II
-
Applied Rigaku Technologies, Inc
NEX CG II, a powerful second-generation energy dispersive X-ray fluorescence (EDXRF) spectrometer, delivers rapid qualitative and quantitative determination of major and minor atomic elements in a wide variety of sample types — from oils and liquids to solids, metals, polymers, powders, pastes, coatings, and thin films.
-
Product
DELTA™ II 2-zone Flow Ratio Controller
-
The DELTA™ II Flow Ratio Controller divides and controls mixed process gas flows to either multiple chambers or zones within a process chamber at ratios specified by the user maximizing process uniformity and repeatability. It is available with EtherCAT® or DeviceNet™ communications.
-
Product
WAN Tester II
-
The Telinc WAN Tester II is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including DDS, T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 NTUs, multiplexers, CSU/DSUs, T-1 CSUs, DTUsand TIUs. It includes a speaker to listen to voice in a DS0. It is supplied with changeable nickel metal hydride batteries and a built-in charger.
-
Product
Minihelic II Differential Pressure Gages
2-5000
-
Combining clean design, small size and low cost with enough accuracy for all but the most demanding applications our Minihelic II gage offers the latest in design features for a dial type differential pressure gage. It is our most compact gage but is easy to read and can safely operate at total pressures up to 30 psig.
-
Product
InfiniiMax II Series Probe Amplifier, 10 GHz
1168B
-
Provides a large common mode range and a large offset range for measuring differential and single-ended signals.
-
Product
OBD Protocol Diagnostics
-
Our innovative OBD Protocol Diagnostics comes with diagnostic break-out boxes and CAN network testers which can expedite maintenance, and streamline the troubleshooting process at the system, subsystem, and component-level by simplifying the access to test ECU signals.
-
Product
MultiPoint II Level Switch
-
The Multipoint II level switch product offers three control points located anywhere along a single vertically inserted level sensing element. One control point can be set up for differential measurement for pump control. This product is best suited to sump level control and batch processing.
